APBoot 1.2.6.7 (build 30025) Built: 2011-08-30 at 17:41:16 Model: AP-13x CPU: 88F6560 A0 (DDR3) Clock: CPU 1600MHz, L2 533MHz, SysClock 533MHz, TClock 200MHz DRAM: 256MB POST1: mem 0 [08][08][08][08][08][08]mem 1 [08][08][08][08][08][08]mem 2 [08][08][08][08][08][08]mem 3 [08][08][08][08][08][08]passed Flash: 16 MB Power: 802.3af POE LAN: done PHY: ....[08][08][08][08]done PEX 0: RC, link up, x1 bus.dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00.00 00 11ab 6560 00005 02 f1000000 00000000 00000000 00000000 00.01 00 168c 0030 00002 01 90000000 00000000 00000000 00000000 PEX 1: RC, link up, x1 bus.dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 01.00 00 11ab 6500 00005 02 f1000000 00000000 00000000 00000000 01.01 00 168c 0030 00002 01 94000000 00000000 00000000 00000000 Net: eth0, eth1 Radio: ar9390#0, ar9390#1 Hit to stop autoboot: 2 [08][08][08] 0 apboot> purgeenv purgeenv Erasing flash...Writing to flash...done apboot> save save Saving Environment to Flash... Erasing flash...Writing to flash...done apboot> boot boot Checking image @ 0xf8100000 Copying image from 0xf8100000 Image is signed; verifying checksum... passed Signer Cert OK Policy Cert OK RSA signature verified. ## Booting image at 02000200 ... Uncompressing... done Aruba Networks ArubaOS Version 6.1.2.3-2.0.0.3 (build 31389 / label #31389) Built by p4build@bermuda on 2011-12-02 at 16:04:24 PST (gcc version 4.3.3) Memory: 256MB = 256MB total Memory: 243712KB available (2564K code, 8852K data, 4416K init, 0K highmem) Delay calibration in progress: Calibrating delay loop... 1597.44 BogoMIPS (lpj=1597440) PEX0 interface detected Link X1 PEX1 interface detected Link X1 wdt: registered with refresh Enabling Watchdog i2c /dev entries driver i2c-arran: using default base 0xf1018100 Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT Starting Kernel DES KAT ...Completed Kernel DES KAT Starting Kernel AES KAT ...Completed Kernel AES KAT Domain Name: arubanetworks.com No panic info available Ethernet port 1 mode: tunnel Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008) eth0: link up, full duplex, speed 100 Mbps ADDRCONF(NETDEV_UP): bond0: link is not ready eth0: link up, full duplex, speed 100 Mbps bonding: bond0: making interface eth0 the new active one. bonding: bond0: first active interface up! bonding: bond0: enslaving eth0 as an active interface with an up link. ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready eth1: link down ADDRCONF(NETDEV_UP): eth1: link is not ready Ethernet uplink active. Becoming Mesh Portal AP xml model 51, num_radios 2 (jiffies 4422) init_asap_mod: installation:0 radio 0: band 1 ant 0 max_ssid 16 radio 1: band 0 ant 0 max_ssid 16 election init: rand=1c HZ=500 ethernet_device_event: dev eth0 is register ethernet_device_event: dev eth0 is up ethernet_device_event: dev eth1 is register ethernet_device_event: dev eth1 is up setting bond0 as bridge child setting gre0 as split child Starting watchdog process... Getting an IP address... eth0: link up, full duplex, speed 100 Mbps 192.168.15.139 255.255.255.0 192.168.15.1 Starting Webserver bind: Transport endpoint is not connected bind: Transport endpoint is not connected bind: Transport endpoint is not connected bind: Transport endpoint is not connected NTP Server not saved in flash... using default ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, PRIVATE_DIAG, WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_rate_atheros: Aruba Networks Rate Control Algorithm ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_spectrum: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_pci: 0.9.4.5 (Atheros/multi-bss) Shutting down eth1 due to insufficient POE voltage [power profile 2] wifi0: Base BSSID d8:c7:c8:3c:db:10, 16 available BSSID(s) eth0 address=d8:c7:c8:cb:cd:b0 br0 address=d8:c7:c8:cb:cd:b0 wifi0: AP type AP-135, radio 0, max_bssids 16 wifi0: Atheros 9380: mem=0xf3000000, irq=25 hw_base=0xd31c0000 wifi1: Base BSSID d8:c7:c8:3c:db:00, 16 available BSSID(s) eth0 address=d8:c7:c8:cb:cd:b0 br0 address=d8:c7:c8:cb:cd:b0 wifi1: AP type AP-135, radio 1, max_bssids 16 wifi1: Atheros 9380: mem=0xf4000000, irq=24 hw_base=0xd3340000 Starting FIPS KAT ... Completed FIPS KAT shutting down watchdog process (nanny will restart it)... <<<<< Welcome to the Access Point >>>>> ip_time_handler: Got ip and packets on bond0 Started master election 47-0 process `snmpd' is using obsolete setsockopt SO_BSDCOMPAT asap_send_elected_master: sent successfully wait for stm to initialize over asap_send_elected_master: sent successfully User: asap_send_elected_master: sent successfully vap aruba000 vlan is 0. fwd-mode:0 mesh