Access Points

Reply
Occasional Contributor II
Posts: 67
Registered: ‎06-04-2009

show ap bss-table cmmand shows one more bssid

Hi all,

when i executed the command show ap bss-table it shows one bss that i didn't configure in the AP 70 and most of its parameters are N/a

here is the outpot of the command :


(Aruba200) #show ap bss-table

Aruba AP BSS Table
------------------
bss ess s/p ip phy type ch/EIRP/max-EIRP cur-cl ap name in-t(s) tot-t mtu acl-state acl
--- --- --- -- --- ---- ---------------- ------ ------- ------- ----- --- --------- ---
00:1a:1e:ef:59:82 CS-WIFI 1/0 1.1.1.3 g ap 1/20/20 0 AP65 2 0 2h:19m:20s 1200 - 1
00:0b:86:04:69:21 CS-WIFI 1/0 10.3.3.140 g ap 11/16.5/20 0 AP 70 0 1d:23h:45m:33s 1500 - 1
00:1a:1e:ef:59:83 for_wep 1/0 1.1.1.3 g ap 1/20/20 2 AP65 2 0 2h:19m:20s 1200 - 58
00:0b:86:04:69:22 for_wep 1/0 10.3.3.140 g ap 11/16.5/20 2 AP 70 0 1d:23h:45m:33s 1500 - 58
00:1a:1e:ef:d1:40 EkahauRTLS 1/0 10.3.3.142 g ap 1/20/20 2 AP 65 1 0 1d:23h:12m:33s 1500 - 58
00:1a:1e:ef:d1:41 CS-WIFI 1/0 10.3.3.142 g ap 1/20/20 0 AP 65 1 0 1d:23h:12m:33s 1500 - 1
00:1a:1e:ef:d1:42 for_wep 1/0 10.3.3.142 g ap 1/20/20 1 AP 65 1 0 1d:23h:12m:33s 1500 - 58
00:1a:1e:ef:59:81 EkahauRTLS 1/0 1.1.1.3 g ap 1/20/20 2 AP65 2 0 2h:19m:20s 1200 - 58
00:0b:86:04:69:20 EkahauRTLS 1/0 10.3.3.140 g ap 11/16.5/20 2 AP 70 0 1d:23h:45m:34s 1500 - 58
00:0b:86:c8:46:93 N/A 1/0 10.3.3.140 e N/A N/A N/A AP 70 0 1d:23h:45m:34s 1500 N/A N/A

Channel followed by "*" indicates channel selected due to unsupported configured channel.

Num APs:10
Num Associations:11
Guru Elite
Posts: 20,762
Registered: ‎03-29-2007

E

That "e" in the phy table is for Ethernet. If users come in on the second port of that AP70, their BSS is the ethernet port.


Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Search Airheads
Showing results for 
Search instead for 
Did you mean: