Aruba Instant & Cloud Wi-Fi

Reply
Frequent Contributor II
Posts: 110
Registered: ‎01-25-2013

Instant CLI

Hey all,

 

I've been tasked with composing a doc for my team that'll detail commands used to create VAPs and such from CLI, but after going through the entire manual, other than finding a lot of really useful commands that I didn't know about, I didn't find anything on the creation of VAPs and such via CLI. Truly, the only way to mass configure Aruba Instant APs is to setup the config file and then push it via AirWave, but I just wanted to double-check before I told them that it couldn't be done.

 

Any info that anyone could offer would be appreciated.

 

Thanks!

 

Ryan

Aruba
Posts: 1,635
Registered: ‎04-13-2009

Re: Instant CLI

Instant does not have the concept of Virtual APs the way the controller-based architecture does.  Please see the attached CLI user guide, specifically the section on wlan ssid-profile.

 

As you mention, you can use AirWave (or Aruba Central) to configure the Instant APs as well.  AirWave offers both template based configuration and GUI configuration.

 

wlan ssid-profile <ssid_profile>
a-max-tx-rate <rate>
a-min-tx-rate <rate>
air-time-limit <limit>
auth-server <name>
auth-survivability
bandwidth-limit <limit>
blacklist
broadcast-filter <type>
captive-portal {<type>[exclude-uplink <types>]|external[exclude-uplink <types>| profile
<name>[exclude-uplink <types>]]}
content-filtering
deny-inter-user-bridging
deny-local-routing
disable
dmo-channel-utilization-threshold <threshold>
dot11k
dot11r
dot11v
dtim-period <value>
dynamic-multicast-optimization
enable
enforce-dhcp
essid <essid>
external-server
g-min-tx-rate <rate>
g-max-tx-rate <rate>
hide-ssid
hotspot-profile <name>
inactivity-timeout <interval>
index <idx>
key-duration <duration>
l2-auth-failthrough
leap-use-session-key
local-probe-req-thresh <threshold>
mac-authentication
mac-authentication-delimiter <delim>
mac-authentication-upper-case
max-authentication-failures <limit>
max-clients-threshold <Max_clients>
multicast-rate-optimization
okc-disable
opmode <opmode>
per-user-bandwidth-limit <limit>
radius-accounting
radius-accounting-mode {user-association|user-authentication}
radius-interim-accounting-interval <minutes>
radius-reauth-interval <minutes>
rf-band <band>
server-load-balancing
set-role <attribute> {{contains|ends-with|equals|matches-regular-expression|not-equals|starts-with} <operand> <role>|value-of}
set-role-by-ssid
set-role-mac-auth <mac_only>
set-role-machine-auth {<machine-only>|<user-only>}
set-role-pre-auth <role>
set-role-unrestricted
set-vlan <attribute> {{contains|ends-with|equals|matches-regular-expression|not-equals|starts-with} <operand> <vlan>|value-of}
termination
type {employee|voice|guest}
vlan <vlan>
wep-key <wep-key>
wispr
wmm-background-dscp <dscp>
wmm-background-share <share>
wmm-best-effort-dscp <dscp>
wmm-best-effort-share <share>
wmm-video-dscp <dscp>
wmm-video-share <share>
wmm-voice-dscp <dscp>
wmm-voice-share <share>
work-without-uplink
wpa-passphrase <wpa-passphrase>
zone <zone>
no…

------------------------------------------------
Systems Engineer, Northeast USA
ACCX | ACDX | ACMX

Frequent Contributor II
Posts: 110
Registered: ‎01-25-2013

Re: Instant CLI

Thanks, clembo. As previously stated, I was aware of the CLI guide, but just wanted to double check. I'll be reviewing the config section on the Airwave Deployment pdf.

 

Thanks again,

 

Ryan

Search Airheads
Showing results for 
Search instead for 
Did you mean: