Campus Switching and Routing

Reply
New Contributor

Airwave 8.2 and HP 2920 Zerotouch

I am trying to get zero touch working with our 2920's. I currently am on version 16.02.0012 of the switch OS and on Airwave 8.2.5. I have my switch setup in Aruba activate and the switch get's my Airwave address with no issues, but from there the switch will not talk with Airwave. In the logs for the switch I only get the following:

 

I 11/14/17 17:06:11 05102 amp-server: AMP server registration started through Primary VLAN.

I 11/14/17 17:06:11 05103 amp-server: Device registration to AMP server failed.

 

The switch can ping the Airwave server so not sure what the issue could be.

 

Thank you.

Guru Elite

Re: Airwave 8.2 and HP 2920 Zerotouch

When you have access to the switch's commandline, you should type:

 

debug ztp

debug destination session

 

That might give you more info.  You have the right time, which is important.

 

If you decide to make changes on the Airwave/Activate side and don't reboot the switch, you might be able to force activation by typing "activate provision force"



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

New Contributor

Re: Airwave 8.2 and HP 2920 Zerotouch

enabled the commands and now get this error:

 

0000:00:03:18.36 ZTP mairwaveCtrl:Default, Primary or Management VLAN is

   configured with IP or DHCP

0000:00:03:18.47 ZTP mairwaveCtrl:AMP server registration started through

   Primary VLAN.

0000:00:03:18.57 ZTP mairwaveCtrl:IPSEC ZTP: Controller is not discovered

0000:00:03:18.65 ZTP mairwaveCtrl:IPSEC ZTP: Check-in to Airwave without IPSec

0000:00:03:18.73 ZTP mairwaveCtrl:sending request to

   https://x.x.x.x/switch_https

0000:00:03:18.83 ZTP mairwaveCtrl:Added X-Type: Device-Reg

0000:00:03:18.89 ZTP mairwaveCtrl:Added X-OEM: HP

0000:00:03:18.94 ZTP mairwaveCtrl:Added X-Mode: SWITCH

0000:00:03:19.00 ZTP mairwaveCtrl:Added X-Current-Version: WB.16.02.0012_485

0000:00:03:19.08 ZTP mairwaveCtrl:Added X-Device-Info: SG73FLX6XN,

   9C:DC:71:FD:C9:40, 2920-24G-PoE+ Switch

0000:00:03:19.20 ZTP mairwaveCtrl:Added X-Group: HP 2920 Switches

0000:00:03:19.27 ZTP mairwaveCtrl:Added X-Folder: Top

0000:00:03:19.32 ZTP mairwaveCtrl:Added X-Shared-Secret: XXXXXXX

0000:00:03:19.39 ZTP mairwaveCtrl:Added X-Device-State: Factory

0000:00:03:19.46 ZTP mairwaveCtrl:Switch registration failed 35 -

0000:00:03:19.53 ZTP mairwaveCtrl:Error string: SSL connect error

0000:00:03:19.60 ZTP mairwaveCtrl:Registration with AMP server failed.

   Scheduling retry in 60 seconds

Guru Elite

Re: Airwave 8.2 and HP 2920 Zerotouch

Does your switch have access to the internet?  It needs to have the time correct to be able to connect to Airwave Via SSL correctly, or you would need to set the time manually.  From what I understand 16.04.xxxx have this fixed.  Can you set the time manually and try to do an activate force?

 

 



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

New Contributor

Re: Airwave 8.2 and HP 2920 Zerotouch

yes the switch can access the internet and it's getting the updated time, just not within the same timezone as the airwave server so there is a 5 hour different from what I can tell

Highlighted
New Contributor

Re: Airwave 8.2 and HP 2920 Zerotouch

Just upgraded the switch to 16.4.0009 and it registered fine with Airwave and was added to the correct group.

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: