Campus Switching and Routing

Reply
Aruba Employee
Posts: 5
Registered: ‎02-03-2016

HPE 5930 40G QSFP+ TO 4 10G DAC CONNECTIONS TO AURBA 72XX CONTROLLER - CONNECTIVITY VERIFIED

VERIFICATION LAB CONNECTIVITY

PARTS

JG726A – FF 5930-32QSFP+

JG330A – X240 QSFP+ TO 10G SFP+ DAC 3M SPLITTER CABLE

7210-US – ARUBA 7210-US MOBILITY CONTROLLER

 QSFP.png

  

HPE 5930 40 GIGABIT TO 10 GIGABIT SETUP

  1. ENSURE THAT THE 5930 FOURTY GIGABIT INTERFACES CAN BE BROKE OUT INTO MULTIPLE 10 GIGABIT INTERFACES **
  2. THIS COMMAND SEQUENCE CHANGES THE 40 GIGABIT INTERFACE TO SUPPORT 4 10 GIGABIT INTERFACES
    1. interface FortyGigE 1/0/28
    2. using tengige
  3. TO ACCESS THE NEW 10 GIGABIT INTERFACE
    1. interface Ten-GigabitEthernet 1/0/28:1-4 (CABLE LABEL A-D)

 

ARUBA 7210 SETUP

  1. PLUG AND PLAY

 

VERIFICATION OF CONNECTIVITY (HPE 5930)

[DC1-5930-2]display interface Ten-GigabitEthernet 1/0/28:1 brief

Brief information on interfaces in bridge mode:

Link: ADM - administratively down; Stby - standby

Speed: (a) - auto

Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface            Link Speed   Duplex Type PVID Description

XGE1/0/28:1          UP   10G(a)  F(a)   A    1

 

[DC1-5930-2]display interface Ten-GigabitEthernet 1/0/28:2 brief

Brief information on interfaces in bridge mode:

Link: ADM - administratively down; Stby - standby

Speed: (a) - auto

Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface            Link Speed   Duplex Type PVID Description

XGE1/0/28:2          UP   10G(a)  F(a)   A    1

 

[DC1-5930-2]display interface Ten-GigabitEthernet 1/0/28:3 brief

Brief information on interfaces in bridge mode:

Link: ADM - administratively down; Stby - standby

Speed: (a) - auto

Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface            Link Speed   Duplex Type PVID Description

XGE1/0/28:3          DOWN auto    A      A    1

 

DC1-5930-2]display interface Ten-GigabitEthernet 1/0/28:4 brief

Brief information on interfaces in bridge mode:

Link: ADM - administratively down; Stby - standby

Speed: (a) - auto

Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface            Link Speed   Duplex Type PVID Description

XGE1/0/28:4          DOWN auto    A      A    1

 

VERIFICATION OF CONNECTIVITY (ARUBA 7210)

(Aruba7210-Master-01) #show interface gigabitethernet 0/0/2

 

GE 0/0/2 is up, line protocol is up

Hardware is 10 Gigabit Ethernet, address is 00:1A:1E:02:3B:CB (bia 00:1A:1E:02:3B:CB)

Description: GE0/0/2 (Fiber Connector)

Encapsulation ARPA, loopback not set

speed (10 Gbps)

MTU 1500 bytes, BW is 10000 Mbit

Last clearing of "show interface" counters 182 day 22 hr 48 min 23 sec

link status last changed 0 day 0 hr 24 min 41 sec

    61 packets input, 20442 bytes

    Received 61 broadcasts, 0 runts, 0 giants, 0 throttles

    0 input error bytes, 0 CRC, 0 frame

    61 multicast, 0 unicast

    5473 packets output, 483967 bytes

    0 output errors bytes, 0 deferred

    0 collisions, 0 late collisions, 0 throttles

This port is TRUSTED

 

(Aruba7210-Master-02) #show interface gigabitethernet 0/0/2

 

GE 0/0/2 is up, line protocol is up

Hardware is 10 Gigabit Ethernet, address is 00:1A:1E:02:3A:3B (bia 00:1A:1E:02:3A:3B)

Description: GE0/0/2 (Fiber Connector)

Encapsulation ARPA, loopback not set

speed (10 Gbps)

MTU 1500 bytes, BW is 10000 Mbit

Last clearing of "show interface" counters 182 day 22 hr 49 min 57 sec

link status last changed 0 day 0 hr 26 min 11 sec

    67 packets input, 21861 bytes

    Received 67 broadcasts, 0 runts, 0 giants, 0 throttles

    0 input error bytes, 0 CRC, 0 frame

    67 multicast, 0 unicast

    2863 packets output, 183232 bytes

    0 output errors bytes, 0 deferred

    0 collisions, 0 late collisions, 0 throttles

This port is TRUSTED

 

** The HPE 5930-32QSFP+ supports 40GbE to 4x10GbE fan out cables in 24 of the 32 QSFP+ ports (ports 5-28).

 

The 5930-2Slot switch supports splitting all of the fixed 40GbE ports and the modular 40GbE ports into 4x10GbE ports using fan-out cables.

 

The 5930-4Slot switch supports splitting 40GbE ports into 4x10GbE ports using fan out cables noting the following restrictions:

  • The 2x40GbE ports on the 24 port SFP+/2 port QSFP+ modules (JH180A, JH181A, JH184A, JH182A) cannot be split into 4x10GbE ports
  • The last two 40GbE ports (ports 7&8) on the 8 port QSFP+ module (JH183A) cannot be split into 4x10GbE ports

 

Occasional Contributor I
Posts: 5
Registered: ‎05-04-2016

Re: HPE 5930 40G QSFP+ TO 4 10G DAC CONNECTIONS TO AURBA 72XX CONTROLLER - CONNECTIVITY VERIFIED

Have a similar case: 72xx (DAC SFP+) ==(LAG)==> 5900AF (SFP+)

 

Thanks for the INFO.

Search Airheads
Showing results for 
Search instead for 
Did you mean: