- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Instant Login
Instant Login
02-03-2014 02:21 AM
I Have just rebooted all my access points, I now can't login in to the instant web UI is says login failure.
I am using the same username and password that I used to login to reboot the AP's.
I have tried the default username and password!
All my SSID still exist so the config hasn't been wiped?!?
Any help would be appreciated.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Alert a Moderator
Re: Instant Login
Re: Instant Login
02-03-2014 04:14 AM
If you've exhausted all opportunities at remembering the password, you can reset it using a similar process to the controllers.
Console to the Master AP.
username = admin
password = forgetme!
To see the password:
encrypt disable
show mgmt-user
To reset the password:
configuration terminal
mgmt-user admin <password>
exit
write memory
Systems Engineer, Northeast USA
AMFX | ACCX | ACDX | ACMX
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Alert a Moderator
Re: Instant Login
Re: Instant Login
02-03-2014 10:46 PM
I have tried the same command but still it showing the passwords in encrypted form
(IMH-MC3600) #show mgmt-user
Management User Table
---------------------
USER PASSWD ROLE STATUS
---- ------ ---- ------
test df48654a011cd8d92e5a8fe1b48a79c3ae50c74076f9853dec read-only ACTIVE
admin b63274d601ab5c352b2f1792805c0183a048a94524e0745aa3 root ACTIVE
Syed Murad Ali
ACMP ACMA CCNA
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Alert a Moderator
Re: Instant Login
Re: Instant Login
02-03-2014 11:37 PM
By the wat I tested it on controller not IAP. Please advice if its different from controller.
Syed Murad Ali
ACMP ACMA CCNA
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Alert a Moderator
Re: Instant Login
Re: Instant Login
02-04-2014 01:10 AM
For the controller, it is the same method as mentioned.
Useranme password
Password: forgetme!
go to configure terminal and use mgmt-user admin root. Then follow by the passwords twice.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Alert a Moderator
Re: Instant Login
Re: Instant Login
02-04-2014 01:17 AM
Hi
Thanks for the reply, I didn't need to do anything in the end as about 3 hours after the reboot, the 11A/N and 11B/G/N lights on the APs went red and then 30 mins later went back to green. I could then login to the web UI again using the correct password.
Cheers
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Alert a Moderator
Re: Instant Login
Re: Instant Login
02-04-2014 01:22 AM
Syed Murad Ali
ACMP ACMA CCNA
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Alert a Moderator
Re: Instant Login
Re: Instant Login
02-04-2014 01:40 AM
You are not able to observe administrator passwords.
Colin Joseph
Aruba Customer Engineering
Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Alert a Moderator
Re: Instant Login
Re: Instant Login
02-04-2014 02:02 AM
Syed Murad Ali
ACMP ACMA CCNA
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Alert a Moderator
Re: Instant Login
Re: Instant Login
02-04-2014 02:08 AM
Yes. That is a big security no-no
Colin Joseph
Aruba Customer Engineering
Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Alert a Moderator