Controllerless Networks

Reply
New Contributor
Posts: 3
Registered: ‎10-26-2014

RAP-108 Question about instant software

Hello Fello Airheads!

 

I have a RAP-108 that doesnt seem to want to be an IAP. I believe that this has the ability to be an IAP but it wont load. Ive tried many different versions of iap software and all have the following output.

 

apboot>
apboot> upgrade os 192.168.10.79:ArubaInstant_Pegasus_6.4.2.0-4.1.1.0_46028
eth0 up: 100 Mb/s full duplex
DHCP broadcast 1
DHCP IP address: 192.168.10.100
DHCP subnet mask: 255.255.255.0
DHCP def gateway: 192.168.10.1
DHCP DNS server: 192.168.10.1
DHCP DNS domain:
Using eth0 device
TFTP from server 192.168.10.79; our IP address is 192.168.10.100
Filename 'ArubaInstant_Pegasus_6.4.2.0-4.1.1.0_46028'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#
done
Bytes transferred = 8562652 (82a7dc hex)
Invalid machine type in image: 0x1a
**** ERROR: upgrade failed ****.
apboot>

 

the device is definitely a RAP-108 also:

APBoot 1.2.7.14 (build 34663)
Built: 2012-07-28 at 11:47:31

Model: RAP-108/RAP-109
CPU: AR9344 revision: 1.2
Clock: 560 MHz, DDR rate: 450 MHz, Bus clock: 225 MHz
DRAM: 128 MB
POST1: passed
Copy: done
Flash: 32 MB
Power: 802.3at POE
PCI: scanning bus 0 ...
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 168c 0033 00002 01 00000004 00000000 00000000 00000000
Net: eth0
Radio: ar9590#0, ar9344#1

 

I can however get the device to boot as a CAP/RAP with the mips32.ari image.

 

Ive tried factory resetting it and all of that but it just never turns into an instant.  Any input would be greatly appreciated. 

 

Thanks!

MVP
Posts: 130
Registered: ‎06-11-2013

Re: RAP-108 Question about instant software

Try the "os_info" command in AP-boot to see if there is an IAP-image available.

 

You can switch to another partition by altering the "os_partition"-variable:

 

setenv os_partition 1 (or 0)

saveenv

boot

 

Are you sure the firmware image is valid? Maybe try re-downloading the firmware image from the support-website.


ACMX#255 | ACMP | ACCP | AWMP
www.securelink.nl
Aruba Employee
Posts: 201
Registered: ‎07-14-2013

Re: RAP-108 Question about instant software

Can you provide the output of mfginfo from APBOOT?

Sent from my iPhone
New Contributor
Posts: 3
Registered: ‎10-26-2014

Re: RAP-108 Question about instant software

From the mfginfo command.

 

mfginfo
Inventory:
Card 0: System
Wired MAC : 6c:f3:7f:c5:13:86
Wired MAC Count : 2
Serial : BV0000215
Date Code : 090812
Wireless MAC : 6c:f3:7f:c5:13:87
Wireless MAC Count : 1
Country : CCODE-US-bc9c5785bebb6115a3331a6c308a4dbb79536633
Card 1: CPU
Assembly : AP-109
Serial : BV0000215
Date Code : 090812
Major Rev : 01
Minor Rev/Variant : 01
apboot>

 

New Contributor
Posts: 3
Registered: ‎10-26-2014

Re: RAP-108 Question about instant software

I think i figured it out!

 

For some reason this device seems to be working just fine with the ORION software for a  IAP-92, IAP-93, IAP-105, IAP-175, RAP-3WN and RAP-3WN. This device is definitely a rap 100 series but when i loaded the orion code it booted perfectly and seems to be working just fine. I upgraded it through the web GUI also. Everything seems to be working as expected!!!

 

Thanks everyone!

Search Airheads
Showing results for 
Search instead for 
Did you mean: