Network Management

Hello, I was wondering if there is a way to setup Airwave to check to see if Radius is authenticating wireless users and if it is not to send an email or some type of alert telling me so?

---

@marchmadness wrote:

Hello, I was wondering if there is a way to setup Airwave to check to see if Radius is authenticating wireless users and if it is not to send an email or some type of alert telling me so?

 

 

---

You bet.

1. Make sure you have enabled SNMP traps on your controller to be sent to Airwave.

2. Create an AMP trigger using the Radius Authentication issues Type

Choose either Client or Device, you can select a count (how many times you want it to occur before being triggered).

As a side, you can also have a report created and emailed to you daily.

Hi Guys

Can Alerts  be triggered to Airwave management once a user gets close to reaching their limit.

Maybe a Radius attribute sent to Airwave? 

How can we do this please?

Thanks

Harry

---

mahathma wrote:

Hi Guys

 

Can Alerts  be triggered to Airwave management once a user gets close to reaching their limit.

Maybe a Radius attribute sent to Airwave? 

How can we do this please?

 

Thanks

Harry

---

Close to reaching what specific limit mahathma?

Hi Colin

When a user reached their allocated quota of say 1GB, I know radius can send COA attribute and Instant AP can change role.

Can an alert be sent to Airwave by radius once this limit is reached?

A separate system must be in place besides airwave to monitor the bandwidth, send a COA and send Airwave a trap or syslog message.  Airwave can then look for that syslog or trap.

Thanks Colin

Dear Friends,

I also have similar question but little different is that 

I want to get alerted when any device down from airwave .

I configured as follows 

system>triggers>add .  then filled all the required fields.  there was alert setting lowest time was 5 minutes. 

For testing purpose, I removed Access Point from the network for 25-30 Minutes but I did not receive an email alert.

Please suggest me to get alerted.

Thank you so much in advance.

Regards 

Ambaraya

Does the access point show as "Down" in Airwave?

Hello CJ,r 

thank you for your reply. Yes it was showing down in airwave.

Can we see screenshots of your rule in Airwave?

Sure, CJ.

Please find attached screenshots.

Please try to get it working with the attached settings, first.

Also make sure that the controller is sending snmp traps to Airwave.

Okay I will Check.

Hey Hi,

As you told me to check only basic configuration, But it is not taking. 

Please find the screenshot for your reference.

Please suggest me.

Thank you

Hi

I have one more doubt, What is sender address ?

what i have to put there?

PFA. 

---

@ambaraya wrote:

Hey Hi,

 

As you told me to check only basic configuration, But it is not taking. 

 

Please find the screenshot for your reference.

 

Please suggest me.

 

Thank you

---

Please check "Send Alerts when upstream device is down" to yes.

Also, you should be able to see the "Alerts" counter in Airwave go up and see the device as down when the controller sends a trap or Airwave has seen the device as down for 5 minutes.

You need to see this before moving onto email alerts.

The sender address should not matter.  The built-in email server should work as long as your DNS server has correct MX records for your domain.  If that does not work, you will have to setup a relay http://community.arubanetworks.com/t5/Wireless-Access/Email-Configuration/td-p/80260

Hi CJ,

"Send Alerts when upstream device is down" to yes is there.

and please find some more screenshots that may give some more info to you to help me.

PFA.

Hi all,

I want to know that CLI commands for IAPs and Virtual controller.

Is IAP CLI commands work for Virtual controller?

Please share here.

Thanks in advance