Security

Reply
Contributor I
Posts: 21
Registered: ‎12-08-2013

ClearPass Guest system deployment

[ Edited ]

I have already deployed over 802.1 x , I now to deploy the guest system,But I have what time it is not clear;

1.Controller configure authentication type is L3 authentication,

2.I  want to Guest SSID to connect visitors will redirect to a page,What kind of authentication type CCPM need to use?

How to configure authorization page?

 

Thanks!

[Mod note: adjusted subject text]

Guru Elite
Posts: 21,001
Registered: ‎03-29-2007

Re: Clear Pass Guest system deployment,I have some questions

You should use a "service template" to configure the guest network on CPPM.  That will simplify creating the services.

 



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

MVP
Posts: 4,269
Registered: ‎07-20-2011

Re: Clear Pass Guest system deployment,I have some questions

 

Please read the attached doc, it will guide through the setup.

Thank you

Victor Fabian
Lead Mobility Engineer @ Integration Partners
AMFX | ACMX | ACDX | ACCX | CWAP | CWDP | CWNA
Contributor I
Posts: 21
Registered: ‎12-08-2013

Re: Clear Pass Guest system deployment,I have some questions

Thanks:

I should use a "service template-----Guest Access" ?

2.But I will lead to the page before configuration is redirected to the following page;How to deal with it, or how to temporarily turn off this feature?

Guru Elite
Posts: 21,001
Registered: ‎03-29-2007

Re: Clear Pass Guest system deployment,I have some questions


Allen@Security wrote:

Thanks:

I should use a "service template-----Guest Access" ?

2.But I will lead to the page before configuration is redirected to the following page;How to deal with it, or how to temporarily turn off this feature?


1.  Yes

2.  The page should be:  https://<ip address of cppm>/guest/guest.php



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Contributor I
Posts: 21
Registered: ‎12-08-2013

Re: Clear Pass Guest system deployment,I have some questions

Thank you very much;

But I see the document set the redirect url inside there is no https:// (CCPM - IP)/guest

The configure of the guide is like this: For example,https://x.x.x.x/web_auth.php

At the bottom of the screenshots;

Guru Elite
Posts: 21,001
Registered: ‎03-29-2007

Re: Clear Pass Guest system deployment,I have some questions

Yes, if you change the default, that is what it should be, what is in the screenshot.  You should be able to click on Test on the Weblogin, to see what URL it should be.



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Contributor I
Posts: 21
Registered: ‎12-08-2013

Re: Clear Pass Guest system deployment,I have some questions

 

The picture as you say,But after the last connection Guest SSID, will be redirected to the OnGuard Portal, as shown in figure;

 


I'll be greatly appreciatived for your answer;

 

 

 

Guru Elite
Posts: 21,001
Registered: ‎03-29-2007

Re: Clear Pass Guest system deployment,I have some questions

Is that what happens when you go to https://<ip address>/guest/cisco_web_auth.php?

 

 



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Contributor I
Posts: 21
Registered: ‎12-08-2013

Re: Clear Pass Guest system deployment,I have some questions

After I connect Guest SSID,Expectations are redirected to a page (https://x.x.x.x/guest/cisco_web_auth.php)

But,But it is redirected to another page(https://x.x.x.x/guest/cisco_web_auth/........php),Has increased a lot uri ;

 

Search Airheads
Showing results for 
Search instead for 
Did you mean: