Wireless Access

Reply
Frequent Contributor I
Posts: 76
Registered: ‎01-03-2014

7010 version 8.1 console connection no permissions

I am trying to set up a lab environement with 8.1 . I upgraded a 7010 to 8.1.0.1 but not sure I set up the config correctly as it will not connect to the MM.    I logon to the console and I am not able to do much as it says I do not have permission to do most things.   I do not see an enable command,  can not look at the config  and since it is not connected to the MM have no way to change anything.   what are my options to reset the 7010 so that I can get it connected to the MM.....  or see why it is not connected.   thanks for any suggestions.

Guru Elite
Posts: 21,489
Registered: ‎03-29-2007

Re: 7010 version 8.1 console connection no permissions

type "whoami" to see your user and role.



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Frequent Contributor I
Posts: 76
Registered: ‎01-03-2014

Re: 7010 version 8.1 console connection no permissions

User: password
Password:
(Aruba7010) *#whoami
You do not have permission to execute this command
(Aruba7010) *#

Guru Elite
Posts: 21,489
Registered: ‎03-29-2007

Re: 7010 version 8.1 console connection no permissions

What user is it?



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Frequent Contributor I
Posts: 76
Registered: ‎01-03-2014

Re: 7010 version 8.1 console connection no permissions

I am not sure what the userid and password is on the device (all of the ones that were there prior to the update do not work), so I was using the password recovery id (password).

Regards,
Dave

MGTS, CCIE #3272
Enterprise Network Technical Support
Texas Instruments Inc.
Off. 214-567-1212
Cell. 214-478-6258
Guru Elite
Posts: 21,489
Registered: ‎03-29-2007

Re: 7010 version 8.1 console connection no permissions

I would start from scratch..



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

MVP
Posts: 1,404
Registered: ‎11-07-2008

Re: 7010 version 8.1 console connection no permissions

Make sure to run through the startup wizard in full-setup mode for the first time through. Also make sure you set up the appropriate settings on the MM in adding the new device. 

Jerrod Howard
Sr. Techical Marketing Engineer
Frequent Contributor I
Posts: 76
Registered: ‎01-03-2014

Re: 7010 version 8.1 console connection no permissions

Is there a doc that describes the first setup as the prompts are not that descriptive.



Sent via the Samsung Galaxy S® 6, an AT&T 4G LTE smartphone
Frequent Contributor I
Posts: 76
Registered: ‎01-03-2014

Re: 7010 version 8.1 console connection no permissions

how do I start from scratch agian,  can not clear the config.  I have gone and booted back to the old 6.5.1 code and then cleared the config but that did not help when I loaded the 8.1.01 code back again.

MVP
Posts: 4,307
Registered: ‎07-20-2011

Re: 7010 version 8.1 console connection no permissions

* Reboot the controller and stop the second boot process (CTRL + X)
* Then type format 0:2
* Then use the bootf 0:0 or 0:1 depending on where the AOS 8 code is located
* Reboot the controller
* Once it comes up go through the wizard by typing full-setup
* If the controller will be tied to a Mobility Master then select MD if not select standalone , then just follow the process
Thank you

Victor Fabian
Lead Mobility Engineer @ Integration Partners
AMFX | ACMX | ACDX | ACCX | CWAP | CWDP | CWNA
Search Airheads
Showing results for 
Search instead for 
Did you mean: