Wireless Access

Hi Everyone

I have an API207,it is connected to DC Supply.

The power light continually flash green on API207.

Reply from 192.168.1.210: bytes=32 time<1ms TTL=64
Reply from 192.168.1.210: bytes=32 time<1ms TTL=64
Reply from 192.168.1.210: bytes=32 time<1ms TTL=64

I do not have a console cable. 

When I installed it i simply plugged it into my switch then I accessed it via the browser at https://instant.arubanetworks.com:4343/#home

Now I cannot access the device.

What causes. ?

Any help would be greatly appreciated

Thanks

---

@geraldst wrote:

Hi Everyone

 

I have an API207,it is connected to DC Supply.

The power light continually flash green on API207.

 

 

Reply from 192.168.1.210: bytes=32 time<1ms TTL=64
Reply from 192.168.1.210: bytes=32 time<1ms TTL=64
Reply from 192.168.1.210: bytes=32 time<1ms TTL=64

 

I do not have a console cable. 

When I installed it i simply plugged it into my switch then I accessed it via the browser at https://instant.arubanetworks.com:4343/#home

Now I cannot access the device.

 

 

What causes. ?

Any help would be greatly appreciated

Thanks

---

How did you determine that the AP is using the IP address 192.168.1.210? Can you ssh to the IP address, or use https://192.168.1.210:4343?

Without console access, troubleshooting will be limited. Do you have local access to the 192.168.1.0 wired subnet?

Hi Charlie,

Thanks for you answer.

From DHCP server, I saw the mac address, then I checked the cable in/out.

I bought the first time in July 2xAP207 (Model:APIN0207 JX952A AP-207) and when I wanted to configure them, I received the same problem "green led flashing on both AP". Back then I opened the RMA and the two devices were replaced. With the new devices I have the same "error".

To solve the problem, I tried:

- DC Supply no result

- PoE Switch no success.

- replace cable

- another place (switch locations)

In the past, I have already worked with identical AP devices, we have in the HQ 3xAP-207 and in the secondary office 7xAP-207  without controller. With these previous devices I didn't have any Problem.

Only with these two new ones I have encountered this error.

Could it be that the new devices themselves have a problem, all four of them?...hard to believe....

Something goes wrong but I can't tell what.

Thank you

Reply from 192.168.178.41: bytes=32 time=1ms TTL=64
Reply from 192.168.178.41: bytes=32 time=1ms TTL=64
Request timed out.
Request timed out.
Reply from 192.168.178.20: Destination host unreachable.
Reply from 192.168.178.20: Destination host unreachable.
Reply from 192.168.178.41: bytes=32 time=3ms TTL=64
Reply from 192.168.178.41: bytes=32 time=1ms TTL=64

- no wifi signal

- no web access

- no SSID (instant-aruba)

- no ssh/telnet

C:\Users\user>arp -a 192.168.178.41

Interface: 192.168.178.20 --- 0x1b
Internet Address Physical Address Type
192.168.178.41 80-8d-b7-c2-11-b4 dynamic

Does the sticker on that access point say IAP-207 or AP-207?  AP-207 would work the way you are describing.  The IAP-207 would broadcast the instant SSID and you would be able to SSH into it.

Thanks for your answer

AP-207

---

@geraldst wrote:

Thanks for your answer

 

 

AP-207

---

The AP-207 does not work without a controller. The models you used previously without a controller would have been IAP-207s. The correct SKU would depend on the country code that needs to be supported.

I bought the wrong item on HP reseller.

This is correct IAP-207-RW.

Thank you Charlie