Wireless Access

Reply
Contributor II

Aruba VMC8.3 run at standalone and RAP109 ipsec error,are the any body can tell us the reason ?

Aruba VMC8.3 run at standalone and RAP109 ipsec error,are the any body can tell us the reason ? If you need any information, please tell us, we will paste here,Thanks微信图片_20180623070049.png

Guru Elite

Re: Aruba VMC8.3 run at standalone and RAP109 ipsec error,are the any body can tell us the reason ?

I will just say that a VMC does not have a built in TPM, so there is a procedure, but it will be difficult.  I have not personally done this successfully.

******************
Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.
******************
Contributor II

Re: Aruba VMC8.3 run at standalone and RAP109 ipsec error,are the any body can tell us the reason ?


(AOS83) [mynode] #show inventory

Mgmt Port HW MAC Addr : 00:16:3E:06:B6:FE
HW MAC Addr : 00:16:3E:05:A5:40
Product key# : MCE39A72C
Activate license : Not Applicable
Active device type : MC-VA-1K
(AOS83) [mynode] #show tpm cert-info

This platform type does not support TPM.
(AOS83) [mynode] #

 

Thanks for your  reply,Please take a look the aboved information from VMC

Regular Contributor I

Re: Aruba VMC8.3 run at standalone and RAP109 ipsec error,are the any body can tell us the reason ?

Hi

As a virtual platform has no TPM you should setup the vpn with a PSK/username&password.

Some info about this from older version. Should still work the same. Go to the : Configuring PSK RAP section

https://www.arubanetworks.com/techdocs/ArubaOS_63_Web_Help/Content/ArubaFrameStyles/Remote_AP/Configuring_the_Secure_R.htm

Hope it helps
Cheers, Frank
Aruba Partner Ambassador| AMFX#22| ACCX#613| ACMX#733| ACDX#744

If you like my posts, kudo's are welcome. If it solves your problem, please click 'Accept as Solution'
Contributor II

Re: Aruba VMC8.3 run at standalone and RAP109 ipsec error,are the any body can tell us the reason ?

Dear Mr

 

Thanks for your help, we have read your docs carefully, and we found that we should provision the rap as cap first, we can not do this, because our VMC is not local one, we can only access them from Internet, Its ip address is 47.104.193.111, we can only connect our VMC from Internet, we can not access it directly. How could we do now ?

License Limits
--------------
Limit Value
----- -----
1000 Access Points
0 RF Protect
0 120abg Upgrade
0 121abg Upgrade
0 124abg Upgrade
0 125abg Upgrade
1000 Next Generation Policy Enforcement Firewall Module
0 Advanced Cryptography
0 Service provider AP
0 WebCC
0 Beta AP
0 MM-VA
1000 MC-VA-RW
0 MC-VA-EG
0 MC-VA-IL
0 MC-VA-JP
0 MC-VA-US
0 VIA
(AOS83) [mynode] (config) #

Regular Contributor I

Re: Aruba VMC8.3 run at standalone and RAP109 ipsec error,are the any body can tell us the reason ?

Hi

I image that you could setup the RAP via CLI by stopping the boot process and entering the vmc IP address and username and password into the settings. On the vmc you then need to setup the user account for RAP.

At this moment I am not able to test this, family needs attention.

Hope it helps.

Cheers, Frank
Aruba Partner Ambassador| AMFX#22| ACCX#613| ACMX#733| ACDX#744

If you like my posts, kudo's are welcome. If it solves your problem, please click 'Accept as Solution'
Contributor II

Re: Aruba VMC8.3 run at standalone and RAP109 ipsec error,are the any body can tell us the reason ?

Yes, we have upgrade our RAP OS in apboot , and make sure the same version to our VMC, and we also set our RAP Master ip as the ipaddr of our VMC

Contributor II

Re: Aruba VMC8.3 run at standalone and RAP109 ipsec error,are the any body can tell us the reason ?

We set only the VMC IP and Remote AP in apboot, how to set the username and password ?

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: