Wireless Access

Reply
Occasional Contributor II
Posts: 51
Registered: ‎03-15-2014

Change LACP Int group ports to access port

Hi,

We currently have our Aruba Switches setup for our wireless Access Points using interface groups with LACP Profiles.

 

I am having trouble changing one of these ports back over to an Access port.

 

Here is the port config:

interface-group gigabitethernet "AP-LACP-GROUP-16"
apply-to 0/0/16,1/0/16
lldp-profile "LLDP-PROFILE"
poe-profile "POE-PROFILE"
enet-link-profile "pc_default"
lacp-profile "AP-LACP-PROFILE-16"
qos trust auto

 

My thought was I could apply

no lacp-profile

switching-profile <vlan# profile>

 

However, I am getting hit with an error on this.

Guru Elite
Posts: 8,792
Registered: ‎09-08-2010

Re: Change LACP Int group ports to access port

What is the error?


Tim Cappalli | Aruba Security TME
@timcappalli | timcappalli.me | ACMX #367 / ACCX #480
Occasional Contributor II
Posts: 51
Registered: ‎03-15-2014

Re: Change LACP Int group ports to access port

See Below

 

(SW-JRSR-IDF5) #configure t 

Enter Configuration commands, one per line. End with CNTL/Z

(SW-JRSR-IDF5) (config) #interface-group gigabitethernet AP-LACP-GROUP-16
(SW-JRSR-IDF5) (gigabitethernet "AP-LACP-GROUP-16") #switching-profile vlan61access
Error: Interface is part of LACP profile: AP-LACP-PROFILE-16, switching profile change not allowed : for interface GE0/0/16

Guru Elite
Posts: 8,792
Registered: ‎09-08-2010

Re: Change LACP Int group ports to access port

Are you trying to leave it as a port-channel and just change it from trunk to access or make it a single link access port?


Tim Cappalli | Aruba Security TME
@timcappalli | timcappalli.me | ACMX #367 / ACCX #480
Occasional Contributor II
Posts: 51
Registered: ‎03-15-2014

Re: Change LACP Int group ports to access port

Make it a single acces port.

 

Here is the config for the port referenced in the error message:

 

(SW-JRSR-IDF5) #show interface-config gigabitethernet 0/0/16

gigabitethernet "0/0/16"
------------------------
Parameter Value Config Derivation
--------- ----- -----------------
Interface MSTP Profile default AP-LACP-GROUP-16
Interface Rapid PVST Profile default AP-LACP-GROUP-16
Interface GVRP Profile N/A gigabitethernet0/0/16
Interface Tunneled Node Profile N/A gigabitethernet0/0/16
Interface VOIP Profile N/A gigabitethernet0/0/16
Interface LLDP Profile LLDP-PROFILE AP-LACP-GROUP-16
Interface PoE Profile POE-PROFILE AP-LACP-GROUP-16
Interface Ethernet Link Profile pc_default AP-LACP-GROUP-16
Interface OAM Profile N/A gigabitethernet0/0/16
Interface LACP Profile AP-LACP-PROFILE-16 gigabitethernet0/0/16
Interface QoS Profile N/A gigabitethernet0/0/16
Interface Policer Profile N/A gigabitethernet0/0/16
Interface AAA Profile N/A gigabitethernet0/0/16
Interface Shutdown Disabled AP-LACP-GROUP-16
Interface MTU 1514 AP-LACP-GROUP-16
Interface Ingress ACL N/A gigabitethernet0/0/16
Interface Egress ACL N/A gigabitethernet0/0/16
Interface QoS Trust Mode Auto AP-LACP-GROUP-16
Interface Description N/A AP-LACP-GROUP-16
Interface Switching Profile default AP-LACP-GROUP-16
Interface Security Profile N/A gigabitethernet0/0/16
Ingress Port Mirroring Profile N/A gigabitethernet0/0/16
Egress Port Mirroring Profile N/A gigabitethernet0/0/16
Static IGMP Multicast Router port for the VLANs 0 AP-LACP-GROUP-16
Static MLD Multicast Router port for the VLANs 0 AP-LACP-GROUP-16
Interface Trusted Mode Enabled AP-LACP-GROUP-16
HSL backup interface N/A gigabitethernet0/0/16
HSL preemption mode Off AP-LACP-GROUP-16
HSL preemption delay 100 AP-LACP-GROUP-16

(SW-JRSR-IDF5) #

Guru Elite
Posts: 8,792
Registered: ‎09-08-2010

Re: Change LACP Int group ports to access port

Remove the LACP profile first (since the port-channel tied to the LACP profile contains a switching-profile), then try to change the switching-profile.


Tim Cappalli | Aruba Security TME
@timcappalli | timcappalli.me | ACMX #367 / ACCX #480
Occasional Contributor II
Posts: 51
Registered: ‎03-15-2014

Re: Change LACP Int group ports to access port

interface-group gigabitethernet "AP-LACP-GROUP-16"
apply-to 0/0/16,1/0/16
lldp-profile "LLDP-PROFILE"
poe-profile "POE-PROFILE"
enet-link-profile "pc_default"
lacp-profile "AP-LACP-PROFILE-16"
qos trust auto

 

applied no lacp-profile command to my int group before attempting to add the switch profile on the int group.

This still provides the error message.

 

interface group now shows:

 

interface-group gigabitethernet "AP-LACP-GROUP-16"
apply-to 0/0/16,1/0/16
lldp-profile "LLDP-PROFILE"
poe-profile "POE-PROFILE"
enet-link-profile "pc_default"
qos trust auto

 

 

 

 

 

 

Guru Elite
Posts: 8,792
Registered: ‎09-08-2010

Re: Change LACP Int group ports to access port

Do you have anything applied directly to those ports?

 

You can run

no interface gigabitethernet 0/0/16

no interface gigabitethernet 1/0/16

to get rid of that config.


Tim Cappalli | Aruba Security TME
@timcappalli | timcappalli.me | ACMX #367 / ACCX #480
Occasional Contributor II
Posts: 51
Registered: ‎03-15-2014

Re: Change LACP Int group ports to access port

That should be it.

Awesome.

Thanks,

 

interface-group gigabitethernet "AP-LACP-GROUP-16"

apply-to 0/0/16,1/0/16
lldp-profile "LLDP-PROFILE"
poe-profile "POE-PROFILE"
enet-link-profile "pc_default"
qos trust auto
switching-profile "vlan61access"

Search Airheads
Showing results for 
Search instead for 
Did you mean: