Wireless Access

Reply
Occasional Contributor II

IAP 315 cant convert to controller 7005

Dear All,

 

I have 1 controller aruba 7005 with AOS 6.5.0 and 8 iap 315 with arubaInstant OS 6.5.0,

 

but these IAP's after I convert to controller, these IAP's detected as airmonitor ap, even if i provisioning to group ap as AP mode,

 

after I upgrade firmware controller to 6.5.4, these IAP's detect as down access point, and always loop restart,

 

even after I upgrade firmware arubaInstant OS of these IAP's to 6.5.4, the problem still happen, detect as down AP on monitoring controller

 

kindly need your advice to troubleshoot it

Occasional Contributor II

Re: IAP 315 cant convert to controller 7005

here's the log from iap when convert process occure :

 

apboot> setenv ipaddr 10.10.10.18
apboot> setenv netmask 255.255.255.0
apboot> setenv gatewayip 10.10.10.1
apboot> saveenv
Saving Environment to Flash...
Erasing flash...
Writing to flash... ...............done
apboot> boot
Booting OS partition 0
Checking image @ 0x0
Invalid image format version: 0x0
Checking image @ 0x2000000
Copying image from 0x44000000

Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
[    0.000000]
[    0.000000] Aruba Networks
[    0.000000] ArubaOS Version 6.5.0.0-4.3.0.0 (build 56428 / label #56428)
[    0.000000] Built by p4build@rhodes on 2016-09-12 at 03:03:01 PDT (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) )
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine: IPQ806X wave-2 board
[    0.000000] Flash variant: default
[    0.000000] msm_reserve_memory: 0x44600000, 0x200000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 123178
[    0.075601] CPU1: Booted secondary processor
[    0.102592] clk_tbl_nss - loaded
[    0.224461] PCI: enabling device 0000:02:00.0 (0140 -> 0143)
[    0.224648] PCI: enabling device 0000:00:00.0 (0140 -> 0143)
[    5.987753] get_bootconfig_partition: no dual boot info in shared memory
[    7.593377] m25p80 spi5.0: found mx25u3235f, expected s25fl512s
[    9.529459] Found AT97SC3203 on i2c-gpio0
[    9.584504] no pmic restart interrupt specified
[   10.224992]
[   10.224992] Starting Kernel SHA1 KAT ...
[   10.277132] Completed Kernel SHA1 KAT
[   10.321899] Starting Kernel HMAC-SHA1 KAT ...Starting Kernel DES KAT ...Completed Kernel DES KAT
[   10.428241] Starting Kernel AES KAT ...Completed Kernel AES KAT
[   10.471946]
[   10.517775] Completed Kernel HMAC-SHA1 KAT
[   10.567760] Starting Kernel AE??pleted Kernel AESGCM KAT
Thu Jan  1 00:00:00 PST 1970
AP-type has_ble_support: ONBOARD.
Domain Name: instant.arubanetworks.com
Disabling ipv6 for devices by default
No panic info available
Writing /dev/ttyHSL2 into /tmp/ble_port
Enabling ble_daemon and ble_relay via nanny
apfcutil: sector CACHE: Cache uninitialized
apfcutil: sector RAP: Cache uninitialized
apfcutil: sector FAT: Cache uninitialized
apfcutil: sector SCRATCH: Cache uninitialized
Backup ENV.
apfcutil: sector MESH Prov: Cache uninitialized
[   15.045673] nss_driver - Turbo Support 1
[   15.085160] nss_driver - fw of size 186944  bytes copied to load addr: 40800000, nss_id : 1
[   16.245610] Found isl28022 on i2c-gpio0
Starting watchdog process...
[   16.320805] Kernel watchdog refresh ended on core 1.
[   16.613027] Kernel watchdog refresh ended on core 0.
Cfg len is 0
Configuration file is empty, turning on default services...
extended ssid activate due to no AP config ...
touching file /tmp/ip_mode_0
eth1 admin down
SIOCGIFFLAGS: No such device
init usb modem ...
insmod: cannot insert `/lib/slhc.ko': File e[   17.252171] usbcore: registered new interface driver usbserial
[   17.358856] usbcore: registered new interface driver usbserial_generic
[   17.436925] USB Serial support registered for generic
[   17.497219] usbserial: USB Serial Driver core
xists (-1): File exists
insmod: cannot insert `/lib/ppp_generic[   17.568978] SCSI subsystem initialized
.ko': File exists (-1): File exists
[   17.732895] Initializing USB Mass Storage driver...
[   17.779006] usbcore: registered new interface driver usb-storage
[   17.850640] USB Mass Storage support registered.
No USB Plugged in
[   37.972164] usbcore: deregistering interface driver usb-storage
[   38.048266] cdrom: Uniform CD-ROM driver unloaded
[   38.103655] USB Serial deregistering driver generic
[   38.157138] usbcore: deregistering interface driver usbserial_generic
[   38.234083] usbcore: deregistering interface driver usbserial
[   40.619618] ADDRCONF(NETDEV_UP): bond0: link is not ready
Ethernet uplink not active yet
Ethernet uplink not active yet
Ethernet uplink not active yet
Ethernet uplink not active yet
Ethernet uplink not active yet
[   46.124523] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
[   46.181880] bond0: 1000Mbps FullDuplexMesh is DISABLED on this device.
copying bootuplog ...

[   47.206529] drvlog_mod: module license 'Proprietary' taints kernel.
[   47.308434] Disabling lock debugging due to kernel taint
[   47.372008] Settng Jumbo MRU 2000
[   47.395845] AP xml model 95, num_radios 2 (jiffies 23695)
[   47.395845] init_asap_mod: installation:0
[   47.395845] radio 0: band 1 ant 0 max_ssid 16
[   47.395845] radio 1: band 0 ant 0 max_ssid 16
[   47.395876] election init: rand=1c HZ=500
[   47.395876] IAP client match init
Disabling wpa_supplicant for this paltform
allow PAPI
notify asap_mod 3g no present...
Starting update SBL2 ...
Prepare update SBL2 ...
The expected MD5: e337c2ee110ce85a0e5d69059fc774b6
The SBL file size: 105484
The /aruba/bin/nor_sbl2.mbn MD5: e337c2ee110ce85a0e5d69059fc774b6
The MD5 of /aruba/bin/nor_sbl2.mbn is correct
[   48.686566] Disabling USB power
[   51.687035] Enabling USB power
105484+0 records in
105484+0 records out
The original SBL2 MD5: e337c2ee110ce85a0e5d69059fc774b6
CMDLINE_WRITE_ENVIRONMENT arg {NEW_SBL2=1}
The SBL2 in flash is same to /aruba/bin/nor_sbl2.mbn
Done.
apdot1x authentication is not enabled
Got all network params from APboot env. Skipping DHCP
Static IP detected. Checking if LACP needs to be configured
LACP setting not required. AP can ping default gateway
[   59.418806] ip_time_handler: Got ip and packets on bond0 Started master election 2-0, rand 23
10.10.10.18 255.255.255.0 10.10.10.1
Compressing all files in the /etc/httpd directory...
Done.
Starting Webserver
bind: Transport endpoint is not connected
bind: Transport endpoint is not connected
bind: Transport endpoint is not connected
bind: Transport endpoint is not connected
Launching NTP Client on pool.ntp.org
[   73.180099] ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D)
[   73.257013] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[   73.368322] ath_dfs: Version 2.0.0
[   73.368322] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
[   73.506123] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[   73.619119] ath_pci:  (Atheros/multi-bss)
[   73.654607] PCI: enabling device 0000:01:00.0 (0140 -> 0142)
[   73.722524] ath_pci 0000:01:00.0: ath DEBUG: sc=0xd9e00800
[   79.473227] Startup Mode-0 set
[   79.498844] htt_peer_map_timer_init Enter pdev dcd88000 hrtimer dcd8a790
[   79.577444]
[   79.577444]  htt_alloc_peer_map_mem : Alloc Success : host q vaddr dc420000 paddr 5d920000
[   79.694095]
[   79.694126]  htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts
[   79.795313] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from dc0c0000
[   79.890971]
[   79.891002] SERIAL NUMBER:  : wifi0
[   79.891002]
[   79.967041] wmi_service_ready_event_rx:  WMI UNIFIED SERVICE READY event
[   80.119650] wmi_ready_event_rx:  WMI UNIFIED READY event
[   80.171852] target uses HTT version 2.2; host uses 2.2
[   80.272945] ol_ath_smart_ant_attach: Firmware doest not support Smart Antenna.
[   80.346954] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna.
[   80.433458] dfs_attach: event log disabled by default
[   80.497032] -1077438292: dev:<wifi0> ic:d9680540 osdev:d9e00810 phy:2wifi0: Base BSSID 34:fc:b9:0d:d0:f0, 16 available BSSID(s) processor ID: 0
[   80.647985] bond0 address=34:fc:b9:c8:dd:0e
[   80.698000] br0 address=34:fc:b9:c8:dd:0e
[   80.745923] wifi0: AP type AP-315, radio 0, max_bssids 16
[   80.810559] Resetting spectral chainmask to Rx chainmask
[   80.977538] Resetting spectral chainmask to Rx chainmask
[   81.028897] Init the PCAP for radio0 offload 1.
[   81.083161] PCI: enabling device 0000:03:00.0 (0140 -> 0142)
[   81.150827] ath_pci 0000:03:00.0: ath DEBUG: sc=0xd9e03c00
[   82.453920] Startup Mode-0 set
[   82.479818] htt_peer_map_timer_init Enter pdev d9ad8000 hrtimer d9ada790
[   82.558169]
[   82.558169]  htt_alloc_peer_map_mem : Alloc Success : host q vaddr dc427000 paddr 5d927000
[   82.674789]
[   82.674789]  htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts
[   82.776007] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from dc300000
[   82.871665]
[   82.871665] SERIAL NUMBER:  : wifi1
[   82.871665]
[   82.947735] wmi_service_ready_event_rx:  WMI UNIFIED SERVICE READY event
[   83.102093] wmi_ready_event_rx:  WMI UNIFIED READY event
[   83.154295] target uses HTT version 2.2; host uses 2.2
[   83.160887] ol_ath_smart_ant_attach: Firmware doest not support Smart Antenna.
[   83.160887] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna.
[   83.160918] dfs_attach: event log disabled by default
[   83.450140] -1077438292: dev:<wifi1> ic:dbf80540 osdev:d9e03c10 phy:2
[   83.526148] wifi1: Base BSSID 34:fc:b9:0d:d0:e0, 16 available BSSID(s) processor ID: 0
[   83.620868] bond0 address=34:fc:b9:c8:dd:0e
[   83.670884] br0 address=34:fc:b9:c8:dd:0e
[   83.718775] wifi1: AP type AP-315, radio 1, max_bssids 16
[   83.783411] Resetting spectral chainmask to Rx chainmask
[   83.846922] Resetting spectral chainmask to Rx chainmask
[   83.910715] Init the PCAP for radio1 offload 1.
[   84.019056]  pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16
[   84.094064]  pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16
AP rebooted caused by cold HW reset(power loss)
shutting down watchdog process (nanny will restart it)...
 
    <<<<<       Welcome to the Access Point     >>>>>
 
Completed SW FIPS KAT test
[   85.657763] busybox (3328): /proc/3326/oom_adj is deprecated, please use /proc/3326/oom_score_adj instead.
User: [   87.582786] Kernel watchdog refresh ended on core 1.
[   87.584786] Kernel watchdog refresh ended on core 0.
[   96.736113] Disabling USB power
[   96.761199] Resetting spectral chainmask to Rx chainmask
[   96.824898] Resetting spectral chainmask to Rx chainmask
[   99.736676] Enabling USB power
[   99.760699] Resetting spectral chainmask to Rx chainmask
[   99.824398] Resetting spectral chainmask to Rx chainmask
[  103.566791] i am master now
[  103.587660] (08:01:32) !!! Init ---> Master
[  103.637644] asap_send_elected_master: sent successfully
Sending SIGKILL to all processes.
Please stand by while rebooting the system.
[  586.267697] Restarting system.
[  586.291690] Going down for restart now


APBoot 1.5.5.7 (build 56398)
Built: 2016-09-08 at 14:21:29

Model: AP-31x
DRAM:  491 MB
SF:    Detected MX25U3235F with page size 64 kB, total 4 MB
Flash: 4 MB
NAND:  132 MiB
PCIE0: link up
PCIE1: link up
       dev fn venID devID class  rev    MBAR0    MBAR1    MBAR2    MBAR3
       00  00  168c  0046 00002   00 00000004 00000000 00000000 00000000
       dev fn venID devID class  rev    MBAR0    MBAR1    MBAR2    MBAR3
       00  00  168c  0040 00002   00 00000004 00000000 00000000 00000000
Power: 802.3af POE
In:    serial
Out:   serial
Err:   serial
Net:   eth0
Radio: qca9983#0, qca9990#1
Reset: warm
FIPS:  passed

Hit <Enter> to stop autoboot:  0
Booting OS partition 0
Checking image @ 0x0
Copying image from 0x44000000

Image is signed; verifying checksum... passed
SHA2 Signature available
Signer Cert OK
Policy Cert OK
RSA signature verified using SHA2.
[    0.000000]
[    0.000000] Aruba Networks
[    0.000000] ArubaOS Version 6.5.4.0 (build 60834 / label #60834)
[    0.000000] Built by p4build@pr-hpn-build05 on 2017-08-04 at 15:40:51 UTC (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) )
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine: IPQ806X wave-2 board
[    0.000000] Flash variant: default
[    0.000000] msm_reserve_memory: 0x44600000, 0x200000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 123178
[    0.075663] CPU1: Booted secondary processor
[    0.102655] clk_tbl_nss - loaded
[    0.224179] PCI: enabling device 0000:02:00.0 (0140 -> 0143)
[    0.224398] PCI: enabling device 0000:00:00.0 (0140 -> 0143)
[    4.969540] m25p80 spi5.0: found mx25u3235f, expected s25fl512s
[    7.468634] Found AT97SC3203 on i2c-gpio0
[    7.527803] no pmic restart interrupt specified
[    8.166916]
[    8.166916] Starting Kernel SHA1 KAT ...
[    8.219025] Completed Kernel SHA1 KAT
[    8.263823] Starting Kernel HMAC-SHA1 KAT ...Starting Kernel DES KAT ...Completed Kernel DES KAT
[    8.370103] Starting Kernel AES KAT ...Completed Kernel AES KAT
[    8.413839]
[    8.459700] Starting Kernel AESGCM KAT ...Completed Kernel HMAC-SHA1 ÿ[    8.586472] Completed Kernel AESGCM KAT
AP-type has_ble_support: ONBOARD.
Domain Name: arubanetworks.com
No panic info available
Writing /dev/ttyHSL2 into /tmp/ble_port
Enabling ble_daemon via nanny
[   12.279256] nss_driver - fw of size 391744  bytes copied to load addr: 40000000, nss_id : 0
[   12.388503] nss_driver - Turbo Support 1
[   12.423024] Supported Frequencies - 110Mhz 550Mhz 733Mhz
[   12.493064] nss_driver - fw of size 190016  bytes copied to load addr: 40800000, nss_id : 1
[   33.241549] drvlog_mod: module license 'Proprietary' taints kernel.
[   33.304123] Disabling lock debugging due to kernel taint
[   33.396688] init_asap_mod: installation:0
[   33.441299] firewall cpu: core-1
Starting watchdog process...
Starting update SBL2 ...
SBL2 was updated already
Done.
Got all network params from APboot env. Skipping DHCP
Static IP detected. Checking if LACP needs to be configured
[   44.312964] Settng Jumbo MRU 2000
cat: /sys/class/net/bond0/bonding/mode: No such file or directory
Bonding mode set to
10.10.10.18 255.255.255.0 10.10.10.1
Running ADP...cat: /tmp/master: No such file or directory
Done. Master is
killall: nanny: no process killed
killall: sapd: no process killed
Sending SIGKILL to all processes.
Unmounting UBIFS completed.
Please stand by while rebooting the system.
[  118.103967] Restarting system.


APBoot 1.5.5.7 (build 56398)
Built: 2016-09-08 at 14:21:29

Model: AP-31x
DRAM:  491 MB
SF:    Detected MX25U3235F with page size 64 kB, total 4 MB
Flash: 4 MB
NAND:  132 MiB
PCIE0: link up
PCIE1: link up
       dev fn venID devID class  rev    MBAR0    MBAR1    MBAR2    MBAR3
       00  00  168c  0046 00002   00 00000004 00000000 00000000 00000000
       dev fn venID devID class  rev    MBAR0    MBAR1    MBAR2    MBAR3
       00  00  168c  0040 00002   00 00000004 00000000 00000000 00000000
Power: 802.3af POE
In:    serial
Out:   serial
Err:   serial
Net:   eth0
Radio: qca9983#0, qca9990#1
Reset: warm
FIPS:  passed

Hit <Enter> to stop autoboot:  0
Booting OS partition 0
Checking image @ 0x0
Copying image from 0x44000000

Image is signed; verifying checksum... passed
SHA2 Signature available
Signer Cert OK
Policy Cert OK
RSA signature verified using SHA2.
[    0.000000]
[    0.000000] Aruba Networks
[    0.000000] ArubaOS Version 6.5.4.0 (build 60834 / label #60834)
[    0.000000] Built by p4build@pr-hpn-build05 on 2017-08-04 at 15:40:51 UTC (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) )
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine: IPQ806X wave-2 board
[    0.000000] Flash variant: default
[    0.000000] msm_reserve_memory: 0x44600000, 0x200000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 123178
[    0.075663] CPU1: Booted secondary processor
[    0.102655] clk_tbl_nss - loaded
[    0.224523] PCI: enabling device 0000:02:00.0 (0140 -> 0143)
[    0.224742] PCI: enabling device 0000:00:00.0 (0140 -> 0143)
[    4.992502] m25p80 spi5.0: found mx25u3235f, expected s25fl512s
[    7.490690] Found AT97SC3203 on i2c-gpio0
[    7.550078] no pmic restart interrupt specified
[    8.189597]
[    8.189597] Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
[    8.268853] Starting Kernel HMAC-SHA1 KAT ...Starting Kernel DES KAT ...Completed Kernel DES KAT
[    8.375164] Starting Kernel AES KAT ...Completed Kernel AES KAT
[    8.418869]
[    8.464667] Completed Kernel HMAC-SHA1 KAT
[    8.514651] Starting Kernel AESGCM KAT ...Completed Kernel AESGCM KAT
AP-type has_ble_support: ONBOARD.
Domain Name: arubanetworks.com
No panic info available
Writing /dev/ttyHSL2 into /tmp/ble_port
Enabling ble_daemon via nanny
[   12.210028] nss_driver - fw of size 391744  bytes copied to load addr: 40000000, nss_id : 0
[   12.319150] nss_driver - Turbo Support 1
[   12.353670] Supported Frequencies - 110Mhz 550Mhz 733Mhz
[   12.423680] nss_driver - fw of size 190016  bytes copied to load addr: 40800000, nss_id : 1
[   33.148890] drvlog_mod: module license 'Proprietary' taints kernel.
[   33.211433] Disabling lock debugging due to kernel taint
[   33.401062] init_asap_mod: installation:0
[   33.446641] firewall cpu: core-1
Starting watchdog process...
Starting update SBL2 ...
SBL2 was updated already
Done.
Got all network params from APboot env. Skipping DHCP
Static IP detected. Checking if LACP needs to be configured
[   44.265010] Settng Jumbo MRU 2000
cat: /sys/class/net/bond0/bonding/mode: No such file or directory
Bonding mode set to
10.10.10.18 255.255.255.0 10.10.10.1
Running ADP...cat: /tmp/master: No such file or directory
Done. Master is
killall: nanny: no process killed
killall: sapd: no process killed
Sending SIGKILL to all processes.
Unmounting UBIFS completed.
Please stand by while rebooting the system.
[  118.109996] Restarting system.


APBoot 1.5.5.7 (build 56398)
Built: 2016-09-08 at 14:21:29

Model: AP-31x
DRAM:  491 MB
SF:    Detected MX25U3235F with page size 64 kB, total 4 MB
Flash: 4 MB
NAND:  132 MiB
PCIE0: link up
PCIE1: link up
       dev fn venID devID class  rev    MBAR0    MBAR1    MBAR2    MBAR3
       00  00  168c  0046 00002   00 00000004 00000000 00000000 00000000
       dev fn venID devID class  rev    MBAR0    MBAR1    MBAR2    MBAR3
       00  00  168c  0040 00002   00 00000004 00000000 00000000 00000000
Power: 802.3af POE
In:    serial
Out:   serial
Err:   serial
Net:   eth0
Radio: qca9983#0, qca9990#1
Reset: warm
FIPS:  passed

Hit <Enter> to stop autoboot:  0

Occasional Contributor II

Re: IAP 315 cant convert to controller 7005

oh, one more,

 

at first initial set up of iap, i dont see my country code I usually use, SG and ID, and my controller country code is SG,

 

the information from IAP is if I dont see my country code, I should try to upgrade to latest firmware, but even I upgrade to 6.5.4.0 which mean latest firmware, I still dont see country code SG or ID

 

kindly need your advice

Contributor I

Re: IAP 315 cant convert to controller 7005

Did you do the conversion process on GUI?

 

In the logs it seems it cant find the master

"Done. Master is"

Maybe try with "setenv master IP"?

Occasional Contributor II

Re: IAP 315 cant convert to controller 7005

i just type like this :

 

setenv ipaddr 10.10.10.1x

setenv netmask 255.255.255.0

setenv gatewayip 10.10.10.1

 

should i put masterip ?

Re: IAP 315 cant convert to controller 7005

The master discovery after the conversion is not working properly:

 

Bonding mode set to
10.10.10.18 255.255.255.0 10.10.10.1
Running ADP...cat: /tmp/master: No such file or directory
Done. Master is

I would advise you first, until things work, to have the APs in the same VLAN as the controller, and use DHCP. From the information that you provide (just from the AP side), it is difficult to make up what is setup incorrectly.

 

 

When APs go into 'Airmonitor' it is likely that there is a regulatory domain issue, for example US type APs on a Rest-of-World controller. Or the controller firmware does not support your AP yet.

 

Sometimes this can be fixed with a DRT (Downloadable Regulatory Table, or something like that), which can be found on the Aruba support site.

 

The support for AP-315 in Singapore (SG) was added in DRT 1.0_57776

AP-315 for Indonesia (ID): DRT 1.0_58226 

 

To check on your controller:

(md-7005-01) #show ap regulatory

Regulatory Version    :1.0_60744
(md-7005-01) #show ap allowed-channels country-code ID ap-type AP-315

Allowed Channels for AP Type AP-315 Country Code "ID" Country "Indonesia"
-------------------------------------------------------------------------
PHY Type                  Allowed Channels
--------                  ----------------
802.11g (indoor)          1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (indoor)          149 153 157 161
802.11g (outdoor)         1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (outdoor)         149 153 157 161
802.11g 40MHz (indoor)    None
802.11a 40MHz (indoor)    None
802.11g 40MHz (outdoor)   None
802.11a 40MHz (outdoor)   None
802.11a 80MHz (indoor)    None
802.11a 80MHz (outdoor)   None
802.11a 160MHz (indoor)   None
802.11a 160MHz (outdoor)  None
802.11a (DFS)             None
(md-7005-01) #show ap allowed-channels country-code SG ap-type AP-315

Allowed Channels for AP Type AP-315 Country Code "SG" Country "Singapore"
-------------------------------------------------------------------------
PHY Type                  Allowed Channels
--------                  ----------------
802.11g (indoor)          1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (indoor)          36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
802.11g (outdoor)         1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (outdoor)         36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
802.11g 40MHz (indoor)    1-5 2-6 3-7 4-8 5-9 6-10 7-11 8-12 9-13
802.11a 40MHz (indoor)    36-40 44-48 52-56 60-64 100-104 108-112 116-120 124-128 132-136 149-153 157-161
802.11g 40MHz (outdoor)   1-5 2-6 3-7 4-8 5-9 6-10 7-11 8-12 9-13
802.11a 40MHz (outdoor)   36-40 44-48 52-56 60-64 100-104 108-112 116-120 124-128 132-136 149-153 157-161
802.11a 80MHz (indoor)    36-48 52-64 100-112 116-128 149-161
802.11a 80MHz (outdoor)   36-48 52-64 100-112 116-128 149-161
802.11a 160MHz (indoor)   36-64 100-128
802.11a 160MHz (outdoor)  36-64 100-128
802.11a (DFS)             52 56 60 64 100 104 108 112 116 120 124 128 132 136 140

Please work with your Aruba partner or Aruba SE if you keep having issues for advice. 

--
If you have urgent issues, please contact your Aruba partner or Aruba TAC (click for contact details).
Contributor I

Re: IAP 315 cant convert to controller 7005

 
Occasional Contributor II

Re: IAP 315 cant convert to controller 7005

thanks for the response

 

how can i apply drt to these IAP sir ?

 

 

Guru Elite

Re: IAP 315 cant convert to controller 7005


Hudaya wrote:

Dear All,

 

I have 1 controller aruba 7005 with AOS 6.5.0 and 8 iap 315 with arubaInstant OS 6.5.0,

 

but these IAP's after I convert to controller, these IAP's detected as airmonitor ap, even if i provisioning to group ap as AP mode,

 

after I upgrade firmware controller to 6.5.4, these IAP's detect as down access point, and always loop restart,

 

even after I upgrade firmware arubaInstant OS of these IAP's to 6.5.4, the problem still happen, detect as down AP on monitoring controller

 

kindly need your advice to troubleshoot it


While the APs are rebooting, type "show log system 50" on the Aruba Controller to see if it says why the APS are rebooting.  You should have a controller with a ROW designation.  Also, type "show ap database" to see if those down APS have a flag.



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Re: IAP 315 cant convert to controller 7005

For Instant AP, the DRT is built into the firmware. However, as you want to convert to controller AP, you will need to have the DRT or proper regulatory support from the installed firmware, only there.

 

When you convert an IAP to AP (Controller), all configuration is lost, and everything is configured and controlled by the controller.

As you mentioned that the APs come up as Air Monitor (I assumed on the controller), that may be because the controller firmware does not support your APs in the firmware and DRT upgrade may solve that and get the APs into normal radio mode.

 

Follow cjoseph's advice and check why the AP does not become active on the controller.

--
If you have urgent issues, please contact your Aruba partner or Aruba TAC (click for contact details).
Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: