Wireless Access

Reply
Contributor I
Posts: 24
Registered: ‎05-07-2013

Is there a command to show all the controllers that use a particular ssid from the master?

I'd like something like this:

show wlan ssid-profile 15150 but that shows all the controllers that have this in their groups.

 

 

Frequent Contributor II
Posts: 128
Registered: ‎03-13-2008

Re: Is there a command to show all the controllers that use a particular ssid from the master?

[ Edited ]

No there is not a command that does what you are asking. All of the SSID profiles are pushed to each controller so there would be no way to determine which controller is using the SSID. 

David Dipert
Contributor I
Posts: 24
Registered: ‎05-07-2013

Re: Is there a command to show all the controllers that use a particular ssid from the master?

Fair enough thanks.

Aruba
Posts: 233
Registered: ‎11-19-2009

Re: Is there a command to show all the controllers that use a particular ssid from the master?

You can get the references of all ap-groups to which ssid profile been used by running below command on the master controller.

 

show references wlan sssid-profile <profile name>

 

This should give the information of what you are looking for.

 

Thank you.

Aruba
Posts: 233
Registered: ‎11-19-2009

Re: Is there a command to show all the controllers that use a particular ssid from the master?

It wouldnt be still providing controller info however references to ap-groups.

Contributor I
Posts: 24
Registered: ‎05-07-2013

Re: Is there a command to show all the controllers that use a particular ssid from the master?

Still kind of the same result...  Thanks though.  Reason I need this is because I need to change a key and was wondering how may controllers it would affect.  I know there are 3 at least controllers for this particular key but I only get the one refrence for the group.  Oh well had to ask...

Guru Elite
Posts: 21,567
Registered: ‎03-29-2007

Re: Is there a command to show all the controllers that use a particular ssid from the master?


billbray wrote:

Still kind of the same result...  Thanks though.  Reason I need this is because I need to change a key and was wondering how may controllers it would affect.  I know there are 3 at least controllers for this particular key but I only get the one refrence for the group.  Oh well had to ask...


if you type "show ap essid" on each controller, it will show you what controllers are broadcasting what SSID and how many users are currently using it.  If you have airwave you can automate this:   login to the SSH shell in Airwave and type

 

on_controllers "show ap essid"

 

It will show you the output for all of your controllers:

 

[root@localhost mercury]# on_controllers "show ap essid"
(Controller1) #show ap essid
  ESSID Summary
  -------------
  ESSID     APs  Clients  VLAN(s)  Encryption
  -----     ---  -------  -------  ----------
  ACME-TLS  1    7        1        WPA2 8021X AES
  CatchMe   1    3        1        WPA2 PSK AES

 

The above is the output from only one controller, by the way.

 

 



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Contributor I
Posts: 24
Registered: ‎05-07-2013

Re: Is there a command to show all the controllers that use a particular ssid from the master?

That does help thank you.  Problem is I have over 100 controllers:)

Guru Elite
Posts: 21,567
Registered: ‎03-29-2007

Re: Is there a command to show all the controllers that use a particular ssid from the master?

[ Edited ]

billbray wrote:

That does help thank you.  Problem is I have over 100 controllers:)


Do you want to  email you with the output file?  No problem:  http://community.arubanetworks.com/t5/Community-Tribal-Knowledge-Base/AirWave-SSH-quot-on-controllers-quot-command/ta-p/16267

 

Do you want to save the output to a file?  just use:

 

[root@localhost mercury]# on_controllers "show ap essid" > output.txt
[root@localhost mercury]# ls
bin/      Makefile.constants         output.txt       support/
install/  Makefile.dev               scripts/         tools/
lib/      Makefile.PG_MAJOR_VERSION  setuid-scripts/
Makefile  mibs/                      src/

 

 Additional Hint:

 

You can also run the "screen" command before running any commands, so that you can exit out of the SSH session and still have it run and complete.

 

 

 



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Contributor I
Posts: 24
Registered: ‎05-07-2013

Re: Is there a command to show all the controllers that use a particular ssid from the master?

I had no idea you could do that...fantastic thank you!

Search Airheads
Showing results for 
Search instead for 
Did you mean: