Wireless Access

Reply
Contributor II
Posts: 45
Registered: ‎05-06-2013

Master/Local access points

Hello,

 

This is likley to be a very stupid question but I am going to ask it anyhow...

 

I am setting up 4 controllers, one master and 3 locals running 6.3.1.2

 

The "issue" I have is that on the master a "show ap database" shows all the access points and which controller they are connected to (a snapshot of this output);

 

AP Database
-----------
Name Group AP Type IP Address Status Flags Switch IP Standby IP
---- ----- ------- ---------- ------ ----- --------- ----------
6c:f3:7f:cc:51:e1 HUB1 105 192.168.210.28 Up 23h:34m:11s 2 192.168.201.12 0.0.0.0
6c:f3:7f:cc:51:f0 HUB10 105 192.168.216.20 Up 40m:4s 2 192.168.201.14 0.0.0.0
6c:f3:7f:cc:92:7c HUB4 105 192.168.213.22 Up 22h:46m:55s 2 192.168.201.13 0.0.0.0

 

and a show ap database off one of the locals;

 

AP Database

-----------
Name Group AP Type IP Address Status Flags Switch IP Standby IP
---- ----- ------- ---------- ------ ----- --------- ----------
6c:f3:7f:cc:51:f0 HUB10 105 192.168.216.20 Up 44m:44s 2I 192.168.201.14 0.0.0.0
6c:f3:7f:cc:51:f6 HUB10 105 192.168.216.17 Up 44m:44s 2I 192.168.201.14 0.0.0.0
6c:f3:7f:cc:51:f7 HUB10 105 192.168.216.18 Up 44m:44s 2I 192.168.201.14 0.0.0.0
6c:f3:7f:cc:92:72 HUB8 105 192.168.215.21 Up 10h:50m:58s 2I 192.168.201.14 0.0.0.0
6c:f3:7f:cc:93:8d HUB8 105 192.168.215.22 Up 10h:50m:58s 2I 192.168.201.14 0.0.0.0

 

but a "show ap active" on all the controllers state that there are 0 ap's.

 

Does the flag 2I on the local have anything to do with this as the I indicates that the ap is Inactive?

 

I am remote at the moment so cant actually check if the SSID's are active.

 

I dont know if this is normal having never setup a master/local before :smileyembarrassed:

 

 

thanks

 

Andy

Contributor II
Posts: 45
Registered: ‎05-06-2013

Re: Master/Local access points

Loaded 6.3.1.3 and I can now see the access points, but dont know if the code or the reboot sorted it :/

 

Frequent Contributor I
Posts: 97
Registered: ‎04-13-2009

Re: Master/Local access points

Hi, 

It looks that they are IKE2 (so CPSec is enabled) and they are inactive due to misconfiguration, lack of the group or VLAN. Please go to Web and at the AP Provisioning under the AP list you have the legend of all the codes. 

HTH

Marek Krauze, CWNE# 174, ACMX #295, ACDX #356
Something cool, helpful or interesting in my post - click the Kudos Star.
Helped to solve your problem - Click Accept as Solution
Contributor II
Posts: 45
Registered: ‎05-06-2013

Re: Master/Local access points

Hi

CPSec is enabled and I am sure the config was right as it all has been working since the reboot.

 

Cheers

Andy

Search Airheads
Showing results for 
Search instead for 
Did you mean: