Wireless Access

Reply
Occasional Contributor I
Posts: 6
Registered: ‎07-29-2013

RAP-3WN instalation

what is the procedure to connect RAP-3WN and aruba 650 controller through point to point connectevity ?

MVP
Posts: 4,307
Registered: ‎07-20-2011

Re: RAP-3WN instalation

[ Edited ]

 

 

Do you mean through the dedicated point to point connection back to where the 650 is located ?

 

What type of RAP are you using  ?

 

If you have routing in place to reach the controller IP address and you allow UDP/4500 :

 

- But all you need is create a ip pool for your RAPs

- then add the mac address to the RAP whitelist 

 

Security VPN_2013-07-29_13-51-23.png

 

Switch General Configuration_2013-07-29_13-52-39.png

 

You can also you this guide :

http://community.arubanetworks.com/aruba/attachments/aruba/branch-wlan-and-remote-access/688/1/Mod12MBC-Remote%20AP-6.1-v1.0.pdf

http://www.arubanetworks.com/wp-content/uploads/RAPVRD_version_8.pdf

 

 

Thank you

Victor Fabian
Lead Mobility Engineer @ Integration Partners
AMFX | ACMX | ACDX | ACCX | CWAP | CWDP | CWNA
Occasional Contributor I
Posts: 6
Registered: ‎07-29-2013

Re: RAP-3WN installation

[ Edited ]

Thanks Victor Fabian for your reply,

 

Yes,point to point connection is back to the 650 controller,

I used RAP-3WN model,it,s act as a remote AP.

Yes,I have reach controller local side IP through point to point circuit,when I attached my laptop in directly to the router and when I connect to the RAP by default ssid(instant).

IP pool is already created in the controller,device Mac id is also white listed in controller.

 

In DSL infrastructure RAP directly converted to standalone to remote access point,and broadcast controller assigned ssid and IP pool but I face problem in point to point connectivity ,it,s converted but after conversion it,s not broadcast anything reboot simultaneously.

 

Arnab Roy

Network Support Enginner

MVP
Posts: 4,307
Registered: ‎07-20-2011

Re: RAP-3WN installation

 

Can you please enable the following ?

 

logging level debugging security process crypto - To determine if it is getting denied 

show log security all | include <rapmacaddress>

 

logging level debugging ap-debug - To see what's going on with the AP 

show log ap-debug all | include <rapmacaddress>

 

And also do a show ap database long | include <rapmacaddress>

 

Also make sure that the ssid is enabled  : show ap essid 

 

Make sure that the AP System profile has the IP address that you are using to point the RAP to the controller

 

Can you please share the AP-Group ?

Thank you

Victor Fabian
Lead Mobility Engineer @ Integration Partners
AMFX | ACMX | ACDX | ACCX | CWAP | CWDP | CWNA
Occasional Contributor I
Posts: 6
Registered: ‎07-29-2013

Re: RAP-3WN installation

in where I enable this function RAP or Controller?

Guru Elite
Posts: 21,488
Registered: ‎03-29-2007

Re: RAP-3WN installation

Arnab,

 

What version of ArubaOS are you using?  You need 6.2 and above to convert a RAP3WN to a Remote AP.

 



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Occasional Contributor I
Posts: 6
Registered: ‎07-29-2013

Re: RAP-3WN installation

I used version 6.1.3.0-3.1.0 in RAP.

Guru Elite
Posts: 21,488
Registered: ‎03-29-2007

Re: RAP-3WN installation

No.  What version on the Aruba Controller?



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Occasional Contributor I
Posts: 6
Registered: ‎07-29-2013

Re: RAP-3WN installation

Name:Aruba Operating System Software.
Model:Aruba650
Version:6.2.1.2
Guru Elite
Posts: 21,488
Registered: ‎03-29-2007

Re: RAP-3WN installation

Okay,

 

Paste in these commands into the controller:

 

config t
logging level debugging security subcat ike
logging level debugging security process aaa
logging level debugging security process authmgr
logging level debugging security subcat l2tp
logging level debugging security subcat vpn

 When the RAP boots up, type "show log security 100" and send us that output, so we can see what is going on.

 



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Search Airheads
Showing results for 
Search instead for 
Did you mean: