Wireless Access

Reply
New Contributor

SSID not broadcasting

i have an aruba 650 and configured for my LAN users to autenticate via domain , 

i did "aaa test-server mschapv2 nps" and authentication was successful.

my problem is that my SSID is not broadcasted though i have done all configurations 

on the controller and WLAN lan is seen on the GUI 

i post output of sh ap database 

 

AP_In_Procurement Office Test 105 192.168.1.127 Up 1m:48s 2 192.168.0.237 0.0.0.0

Flags: U = Unprovisioned; N = Duplicate name; G = No such group; L = Unlicensed
I = Inactive; D = Dirty or no config; E = Regulatory Domain Mismatch
X = Maintenance Mode; P = PPPoE AP; B = Built-in AP
R = Remote AP; R- = Remote AP requires Auth; C = Cellular RAP;
c = CERT-based RAP; 1 = 802.1x authenticated AP; 2 = Using IKE version 2
u = Custom-Cert RAP; S = Standby-mode AP; J = USB cert at AP
M = Mesh node; Y = Mesh Recovery

Total APs:1

 

it shows 2 in the flags column , some1 help.

Aruba

Re: SSID not broadcasting

can you include the full output of "show ap database long" to verify what AP Group the AP is in

 

Also, can you verify the following:

 

show ap bss-table

show ap-group <NameofAPGroup>  .....check if a virtual AP is present; if so, run:

show wlan virtual-ap <NameofVAP> .....check for SSID Profile name

show wlan ssid-profile <NameofSSIDProfile>  ......check for Hide SSID and Deny_Broadcast Probes fields

 

 

------------------------------------------------
Systems Engineer, Northeast USA
ACCX | ACDX | ACMX

New Contributor

Re: SSID not broadcasting

hers is the output 

 

(Aruba650) #show ap database long

AP Database
-----------
Name Group AP Type IP Address Status Flags Switch IP Standby IP Wired MAC Address Serial # Port FQLN Outer IP User
---- ----- ------- ---------- ------ ----- --------- ---------- ----------------- -------- ---- ---- -------- ----
AP_In_Procurement Office Test 105 192.168.1.127 Up 1m:19s 2 192.168.0.237 0.0.0.0 d8:c7:c8:ca:cc:b2 BE0223359 1/2 N/A N/A

Flags: U = Unprovisioned; N = Duplicate name; G = No such group; L = Unlicensed
I = Inactive; D = Dirty or no config; E = Regulatory Domain Mismatch
X = Maintenance Mode; P = PPPoE AP; B = Built-in AP
R = Remote AP; R- = Remote AP requires Auth; C = Cellular RAP;
c = CERT-based RAP; 1 = 802.1x authenticated AP; 2 = Using IKE version 2
u = Custom-Cert RAP; S = Standby-mode AP; J = USB cert at AP
M = Mesh node; Y = Mesh Recovery

Total APs:1

Aruba

Re: SSID not broadcasting

What about the other commands above:

 

show ap bss-table ap-name "AP_In_Procurement Office"

show ap-group Test  .....check if a virtual AP is present; if so, run:

show wlan virtual-ap <NameofVAP> .....check for SSID Profile name

show wlan ssid-profile <NameofSSIDProfile>  ......check for Hide SSID and Deny_Broadcast Probes

------------------------------------------------
Systems Engineer, Northeast USA
ACCX | ACDX | ACMX

Contributor I

Re: SSID not broadcasting

Do you have any vlan settings?  If not, this would keep the SSID from not broadcasting.  Also, check in your VAP profile that the "Virtual AP Enabled" checkbox is checked(GUI) or enabled.

 

Matt

Aruba

Re: SSID not broadcasting

Also, check the following to see if there are any errors preventing it from coming up:  show profile-errors.

 

 

 

 

------------------------------------------------
Systems Engineer, Northeast USA
ACCX | ACDX | ACMX

New Contributor

Re: SSID not broadcasting

Please check this settings.

 

hidessid_denybcast.png

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: