Wireless Access

Reply
Occasional Contributor II
Posts: 25
Registered: ‎07-28-2015

Where do you check to see if the AP is using one VLAN and the wifi user is on different VLAN?

My 2nd question here as a newbie.

 

The controller is the 3600.

I'd like to know as the subject stated where in the controller I can locate this setting.

 

My design goal is to have the AP running in one VLAN 60 and the SSID #1 users are on VLAN 61, the SSID #2 users are on VLAN 62 and so on. 

So I'd like to check the current configuration if it's already setup that way. 

Any helpul hint would be greatly appreciated.

 

Thank you.

 

Guru Elite
Posts: 21,271
Registered: ‎03-29-2007

Re: Where do you check to see if the AP is using one VLAN and the wifi user is on different VLAN?

The Virtual AP has a VLAN parameter that determines what VLAN a user would end up in.  To see what VLAN a user is currently in, on the commandline, type "show user-table verbose".  The VLAN should be in parenthesis.

 



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Occasional Contributor II
Posts: 25
Registered: ‎07-28-2015

Re: Where do you check to see if the AP is using one VLAN and the wifi user is on different VLAN?

The only problem is that none of the AP is connected to the controller at the moment because I'm redoing the vlan. The current Aruba vlans are in conflict with our network so I had to shut it down on the switch.

I don't want to delete them from the controller also because I want to copy the configuration to the new designated vlan.

Hope that make sense? :)

 

I thought I should be able to see how it was configured through the controller GUI without having to have the AP connected first, no?

Sorry, I'm still learning here... :(

 

Occasional Contributor II
Posts: 25
Registered: ‎07-28-2015

Re: Where do you check to see if the AP is using one VLAN and the wifi user is on different VLAN?

Maybe I should share this to make it more sense.

 

I believe the current setting is as follows:

GE1/1 VLAN 1: 10.0.0.1 (LAN for MGMT & APs)

GE 1/0-1 VLAN 2: 38.150.150.38 (WAN IP)

GE 1/1 VLAN 3: 10.3.0.1 (WLAN for Nest SSID)

GE 1/1 VLAN 4: 10.4.0.1 (WLAN for Business SSID)

GE 1/1 VLAN 5: 10.5.0.1 (WLAN for Public SSID)

 

My goal is to have the setup as follows since now we integrate them to our network.

 

GE 1/0-1 VLAN 100: 192.168.100.2 (WAN IP, MGMT LAN, Business SSID WLAN)

GE 1/1 VLAN 150: 192.150.0.1 (LAN for APs)

GE 1/1 VLAN 160: 192.160.0.1 (WLAN for Nest SSID)

GE 1/1 VLAN 170: 192.170.0.1 (WLAN for Public SSID)

 

Hope that makes more sense?

There might be a simple way to set this up and I'm all ears. :)

 

Thank you all.

MVP
Posts: 1,111
Registered: ‎10-11-2011

Re: Where do you check to see if the AP is using one VLAN and the wifi user is on different VLAN?

  1. Create the new VLANs on the controller
  2. Navigate to each VAP and assign the VLAN. Here's a link explaining VAPs.
=======================================
If a reply adequately addresses your issue, please click on the "Accept as Solution" and "Give Kudos" button so this information can benefit other users.
Search Airheads
Showing results for 
Search instead for 
Did you mean: