Hello,
I have a 650 controller, one AP-115 and another AP-205. The problem is APs are not joining the controller although they see it as master controller, they pull their IPs as well from DHCP.
I have configured DHCP option 43 and 60, created DNS forward lookup zone entry and plus APs seem to be using ADP..
However APs still don't join the controller.
Here is the boot process of one access point.
APBoot 1.5.3.5 (build 43311)
Built: 2014-04-19 at 02:39:36
Model: AP-20x
CPU: BCM53011/15, revision A0
I2C: ready
SKU: 2
OTP: 0xeca01028
Clock:
CPU: 800 MHz
DDR: 533 MHz
AXI: 400 MHz
APB: 200 MHz
PER: 400 MHz
DRAM: 128 MB
POST1: memory passed
SF: Detected MX25L25635E with page size 4 kB, total 32 MB
Flash: 32 MB
PCIe0: RC, link up
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 14e4 4360 00002 03 08000004 00000000 00000000 00000000
PCIe1: RC, link up
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 14e4 4360 00002 03 40000004 00000000 00000000 00000000
Power: POE
Net: eth0
Radio: bcm43460#0, bcm43460#1
Hit <Enter> to stop autoboot: 0
apboot> dhcp
DHCP broadcast 1
DHCP IP address: 192.168.0.10
DHCP subnet mask: 255.255.255.0
DHCP def gateway: 192.168.0.1
DHCP DNS server: 192.168.0.25
DHCP DNS domain: homenetwork.lab
Controller address: 192.168.0.3
apboot> boot
Checking image @ 0x1e100000
Copying image from 0x1e100000
Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
Uncompressing... done
[ 0.000000]
[ 0.000000] Aruba Networks
[ 0.000000] ArubaOS Version 6.4.2.14 (build 52696 / label #52696)
[ 0.000000] Built by p4build@lesbos on 2015-11-24 at 13:38:46 PST (gcc version 4.7.2)
[ 0.000000]
[ 0.000000] Flash variant: variant0
[ 0.000000] MPCORE found at 19020000, SCTLR 0x10c53c7f ACTLR 0x00000040 CPSR 0x600001d3 SPSR 0x86004
f61 PRRR 0x000a81a8 NMRR 0x40e040e0
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 120960k/120960k available, 10112k reserved, 0K highmem
[ 0.052000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 3.376000] PMU: registered new PMU device of type 0
[ 3.882000] pci 0001:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
[ 3.884000] pci 0001:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
[ 3.886000] pci 0001:01:00.0: BAR 0: set to [mem 0x08000000-0x08007fff 64bit] (PCI address [0x800000
0-0x8007fff]
[ 4.390000] pci 0002:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff]
[ 4.392000] pci 0002:02:00.0: BAR 0: assigned [mem 0x40000000-0x40007fff 64bit]
[ 4.394000] pci 0002:02:00.0: BAR 0: set to [mem 0x40000000-0x40007fff 64bit] (PCI address [0x400000
00-0x40007fff]
[ 4.738000] i2c-springbank: using remapped base c9d92060
[ 4.740000] mpcore_wdt mpcore_wdt: enabling watchdog.
[ 4.744000] qspi_iproc qspi_iproc.1: 1-lane output, 3-byte address
[ 4.748000] m25p80 spi1.0: mx25l25635e (32768 Kbytes)
[ 4.750000] Creating 1 MTD partitions on "spi1.0":
[ 4.752000] 0x000000000000-0x000002000000 : "qspi"
[ 4.756000]
[ 4.756000] Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
[ 4.760000] Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
[ 4.774000] Starting Kernel DES KAT ...Completed Kernel DES KAT
[ 4.778000] Starting Kernel AES KAT ...Completed Kernel AES KAT
[ 4.780000]
Domain Name: arubanetworks.com
No panic info available
[ 6.280000] AP xml model 81, num_radios 2 (jiffies 3140)
[ 6.282000] init_asap_mod: installation:0
[ 6.284000] radio 0: band 1 ant 0 max_ssid 16
[ 6.286000] radio 1: band 0 ant 0 max_ssid 16
Starting watchdog process...
Getting an IP address...
[ 8.684000] ADDRCONF(NETDEV_UP): bond0: link is not ready
[ 10.688000] bond0: link up (1000FD)
[ 10.690000] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
192.168.0.10 255.255.255.0 192.168.0.1
Running ADP...Done. Master is 192.168.0.3
[ 15.378000] wifi0: AP type AP-205, radio 0, max_bssids 16
[ 15.422000] wifi1: AP type AP-205, radio 1, max_bssids 16
shutting down watchdog process (nanny will restart it)...
<<<<< Welcome to the Access Point >>>>>
~ #
Please advise.