Wireless Access

Reply
Frequent Contributor II
Posts: 149
Registered: ‎04-20-2009

how to delete a port-channel

Is there a way to delete a port-channel that is no longer used.

I tried "no interface port-channel 1" from the cli with no luck and there does not seem to be any obvious method in the GUI.

 

Thanks in advance.

 

 

Guru Elite
Posts: 8,330
Registered: ‎09-08-2010

Re: how to delete a port-channel

What error did you get when you can that command? 


Thanks, 
Tim

Tim Cappalli | Aruba Security TME
@timcappalli | timcappalli.me | ACMX #367 / ACCX #480
Frequent Contributor II
Posts: 149
Registered: ‎04-20-2009

Re: how to delete a port-channel

(config) # no interface port-channel 1

 

% invalid input detected at ' ^ ' marker.

 

The '^' is displayed beneeth the '1'

 

Cheers

Frequent Contributor II
Posts: 149
Registered: ‎01-31-2013

Re: how to delete a port-channel

From the Controller Web Interface you can disable the port-channel clicking on the ports belonging to the port-channel and confirm it doing Apply.

 

 

Cattura.JPG

 

 

 

Thanks,

Massimo

 

[If you found my post helpful, please give kudos]

 

 

 

------------------------------------------------------------
Massimo Gallina
Telecommunications engineer - ACMP2013
Frequent Contributor II
Posts: 149
Registered: ‎04-20-2009

Re: how to delete a port-channel

I understand that this will disable the port-channel.

Same as typing Shutdown from the CLI

 

What I am trying to do is remove the port-channel from my config completely.

in the cisco world its as simple as 

 

no interface port-channel 1 but Aruba does not seem to have an equivelant command.


m.gallina wrote:

From the Controller Web Interface you can disable the port-channel clicking on the ports belonging to the port-channel and confirm it doing Apply.

 

 

Cattura.JPG

 

 

 

Thanks,

Massimo

 

[If you found my post helpful, please give kudos]

 

 

 


 

Guru Elite
Posts: 8,330
Registered: ‎09-08-2010

Re: how to delete a port-channel

[ Edited ]
 

Tim Cappalli | Aruba Security TME
@timcappalli | timcappalli.me | ACMX #367 / ACCX #480
Frequent Contributor II
Posts: 149
Registered: ‎04-20-2009

Re: how to delete a port-channel


(OCDSB-M1-Pri) #show running-config | include port-channel
Building Configuration...
interface port-channel 0
interface port-channel 1

(OCDSB-M1-Pri) #show interface port-channel 0


Port-Channel 0 is administratively up
Hardware is Port-Channel, address is 00:1A:1E:01:7F:48 (bia 00:1A:1E:01:7F:48)
Description: Link Aggregate
Spanning Tree is disabled
Switchport priority: 0
Member port:
GE 0/0/0, Admin is up, line protocol is up
GE 0/0/1, Admin is up, line protocol is up
Last clearing of "show interface" counters 0 day 18 hr 7 min 18 sec
link status last changed 0 day 18 hr 5 min 6 sec
83297 packets input, 6453179 bytes
Received 78116 broadcasts, 0 runts, 0 giants, 0 throttles
0 input error bytes, 0 CRC, 0 frame
69492 multicast, 5181 unicast
33909 packets output, 4355603 bytes
0 output errors bytes, 0 deferred
0 collisions, 0 late collisions, 0 throttles
Port-Channel 0 is TRUSTED


(OCDSB-M1-Pri) #show interface port-channel 1


Port-Channel 1 is administratively down
Hardware is Port-Channel, address is 00:1A:1E:01:7F:48 (bia 00:1A:1E:01:7F:48)
Description: Link Aggregate
Spanning Tree is disabled
Switchport priority: 0
Member port:
Last clearing of "show interface" counters 0 day 18 hr 7 min 38 sec
link status last changed 0 day 18 hr 7 min 38 sec
0 packets input, 0 bytes
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input error bytes, 0 CRC, 0 frame
0 multicast, 0 unicast
0 packets output, 0 bytes
0 output errors bytes, 0 deferred
0 collisions, 0 late collisions, 0 throttles
Port-Channel 1 is TRUSTED

 


cappalli wrote:
That command is definitely valid. Can you run: 

show runn | include port-channel


Thanks, 
Tim



Guru Elite
Posts: 20,807
Registered: ‎03-29-2007

Re: how to delete a port-channel

There is no way to delete a port channel.  If you make it untrusted (the default confguration of a port channel) and no interfaces are assigned to it, it will go away.

 



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Frequent Contributor I
Posts: 64
Registered: ‎11-10-2009

Re: how to delete a port-channel


cjoseph wrote:

There is no way to delete a port channel.  If you make it untrusted (the default confguration of a port channel) and no interfaces are assigned to it, it will go away. 


On top of that, I've found I have to remove all commands that make the port-channel interface differ from the default, e.g.:

 

 

 int port-channel 1

  no trusted

  no switchport mode

  no switchport trunk allowed vlan

 

Probably you have to do other things too (like "no description").  However, once it's all back to the "default" then it disappears.

Search Airheads
Showing results for 
Search instead for 
Did you mean: