Wireless Access

Reply
Frequent Contributor II

mesh redundant portal

I've got a point to multipoint configuration at a customer site and whent he main mesh portal goes down, another portal is supposed to take over. 

 

This is not happening. Once the main portal goes down, the entire mesh goes down and the redundant portal stays up. Where can I check this configuration? The system has worked in the past and just stopped working when upgrading from an old controller to a 7200.

Re: mesh redundant portal

Can you please share how you have this configured ?

Thank you

Victor Fabian
Lead Mobility Engineer @ Integration Partners
AMFX | ACMX | ACDX | ACCX | CWAP | CWDP | CWNA
Frequent Contributor II

Re: mesh redundant portal

I've included everything i think is relevant...

 

 

ap mesh-recovery-profile cluster RecoveryCxXNI8gKXgR3fsvx wpa-hexkey "long encrypted key"

crypto isakmp policy 20

  encryption aes256

!

ap wired-ap-profile "CU-WAP-1"

   wired-ap-enable

   trusted

   switchport access vlan 20

   switchport trunk native vlan 7

!

ap mesh-ht-ssid-profile "default"

!

ap mesh-cluster-profile "default"

!

ap mesh-cluster-profile "Cust_mesh_cluster_1"

   cluster "Cust_mesh_cluster_1"

   opmode wpa2-psk-aes

   wpa-passphrase 68147f72a233e02af9490f6fcad0c403fcce124d5544a31d

!

ap mesh-cluster-profile "Cust_mesh_cluster_2"

   cluster "Cust_mesh_cluster_2"

   opmode wpa2-psk-aes

   wpa-passphrase 42bd0d6f0e8c10b381d744352ee2b7627130fdf0f95626dc

!

ap mesh-radio-profile "Cust_mesh_radio_1"

!

ap mesh-radio-profile "Cust_mesh_radio_2"

 

!

ap wired-port-profile "CU-WAP-1"

   wired-ap-profile "CU-WAP-1"

!

rf arm-profile "Cust_mesh_arm_profile"

   min-tx-power 127

!

rf dot11a-radio-profile "Cust-max-arm-power-rp"

   channel 161

   arm-profile "Cust_mesh_arm_profile"

!

ap-group "AP_Mesh_1_MeSh"

   virtual-ap "Cust_employee_vap"

   virtual-ap "Cust_device_vap"

   dot11a-radio-profile "Cust-max-arm-power-rp"

   dot11g-radio-profile "Cust_mesh_g_radio_profile"

   ids-profile "Cust_ids_low"

   mesh-radio-profile "Cust_mesh_radio_1"

   mesh-cluster-profile "Cust_mesh_cluster_1" priority 1

   mesh-cluster-profile "Cust_mesh_cluster_2" priority 2

!

ap-group "AP_Mesh_2_MeSh"

   virtual-ap "Cust_employee_vap"

   virtual-ap "Cust_device_vap"

   dot11a-radio-profile "Cust-max-arm-power-rp"

   dot11g-radio-profile "Cust_mesh_g_radio_profile"

   enet0-port-profile "CU-WAP-1"

   enet1-port-profile "CU-WAP-1"

   ids-profile "Cust_ids_low"

   mesh-radio-profile "Cust_mesh_radio_1"

   mesh-cluster-profile "Cust_mesh_cluster_2" priority 1

   mesh-cluster-profile "Cust_mesh_cluster_1" priority 2

!



 

Frequent Contributor II

Re: mesh redundant portal

bump?

 

 

Do all portals need to be on the same channel?

Re: mesh redundant portal

They need to be on same mesh link channel on .11a

Thank you

Victor Fabian
Lead Mobility Engineer @ Integration Partners
AMFX | ACMX | ACDX | ACCX | CWAP | CWDP | CWNA
Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: