Wireless Access

Reply
Occasional Contributor II

vlan port- channel controler

hello every one

 

i  have a question about the vlan creation and tag on port chanel 

 

i create a new vlan on conroler and i would like to tag this vlan on on the port chanel who are a trunk with other vlan 

 

when i creat this vlan i see the port chanel have this configuration is it nornal ?

i dont found how to remove this configuration ?

 

switchport access vlan XX

i dont found how to remove this configuration ?

 

i tag the port chanel 

 

i see the this pofiguration en webui with cli command zone

switchport trunk allowed vlan 15,23,32,99,134-138,200-206,812,1001,xx

 

are there a impact if i push this configuration ?

not access on controller ?

beark acces for other vlan ?

 

aruba os 6.0

 

thx 

 

best regards 

 

 

 

 

 

Guru Elite

Re: vlan port- channel controler

Do you want to remove a single vlan from the trunk or do you want to change the trunk into an access port?

******************
Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.
******************
Occasional Contributor II

Re: vlan port- channel controler

 

 

 

 

the actuel configuration is like this 

 

switchport trunk allowed vlan 15,23,32,99,134-138,200-206,812,1001

 

i woulk tag a new vlan on the PO who are on trunk 

 

but there are this config too on the PO 

 

switchport access vlan XX

 

is not good

 

acutualy on the po config :

 

interface port-chanel 3

switchport trunk allowed vlan 15,23,32,99,134-138,200-206,812,1001

switchport access vlan XX

 

i would like remove this config 

 

switchport access vlan XX

 

 

to add a this XX on the trunk allowed on this po 

 

thx

 

 

Guru Elite

Re: vlan port- channel controler

- You should only be configuring the port channel interface

- The "switchport Mode _________" command determines if it is a trunk or an access port.

- If the command under the port channel is "switchport mode trunk", the "switchport access vlan" command is ignored.

 

To ensure that this is a trunk, do this:

config t

interface port channel x

switchport mode trunk

 

To add the vlan:

config t

interface port channel x

switchport trunk allowed vlan add xx

 

 

 

******************
Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.
******************
Occasional Contributor II

Re: vlan port- channel controler

ok to resume i add the new on the trunk on port-chanel and the configuration who was on switchport acces vlan xx will be remove 

 

and i ll have only this configuration on the po 

 

switchport trunk allowed vlan add xx,15,33,44

 

i il do on webui there no impact ? 

 

i ll be sure 

there this configuration on po :

 

inter face port-chanel x

switchport acces vlan xx

switchport trunk allowed vlan add xx,15,33,44

 

after my action 

 

i ll see this configuration on trunk with the new vlan x and i wiil not see "switchpor acces vlan x" 

 

interface portchanel X

switchport trunk allowed vlan add xx,15,33,44,xx

 

is it correct thre ni impact 

no acces breking 

 

 

 

 

 

 

Occasional Contributor II

Re: vlan port- channel controler

can i do this command 

 

no switchport acces vlan X in the po interface ? in cli 

 

 

Guru Elite

Re: vlan port- channel controler

Do you want a trunk or an access port?

******************
Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.
******************
Occasional Contributor II

Re: vlan port- channel controler

a trunk 

 

there are acullay a trunk configuration allowed many vlan 

 

i want add this new lan on the trunk 

Guru Elite

Re: vlan port- channel controler

The instructions in my post before should work.
******************
Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.
******************
Occasional Contributor II

Re: vlan port- channel controler

ok thx 

 

can i do this command 

 

no switchport acces vlan X in the po interface ? in cli

 

and after  add the new vlan on the truck on the PC ? to be clear on the the PC ?

 

 

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: