(Aruba7210_Master_20) #show ap debug driver-log ap-name ArubaAP-011 [ 0.000000] Flash variant: default [ 0.000000] [ 0.000000] Aruba Networks [ 0.000000] ArubaOS Version 6.5.4.2 (build 61807 / label #61807) [ 0.000000] Built by p4build@lesbos on 2017-10-07 at 00:39:00 PDT (gcc version 4.5.1) [ 0.000000] [ 0.000000] Memory: 508540k/524288k available (10060k kernel code, 15748k reserved, 612k data, 376k bss, 6520k init) [ 0.000000] time_init: decrementer frequency = 50.000000 MHz [ 0.000000] time_init: processor frequency = 799.999992 MHz [ 0.000000] clockevent: decrementer mult[ccccccc] shift[32] cpu[0] [ 0.002971] Processor 1 found. [ 0.113022] Brought up 2 CPUs [ 0.190216] PCI: Probing PCI hardware [ 0.233369] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.296361] pci 0001:02:00.0: PCI bridge to [bus 03-ff] [ 0.358587] pci 0000:00:00.0: enabling device (0106 -> 0107) [ 0.425679] pci 0001:02:00.0: enabling device (0106 -> 0107) [ 5.181623] ee000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank [ 5.256672] Amd/Fujitsu Extended Query Table at 0x0040 [ 5.318190] number of CFI chips: 1 [ 5.372764] fsl-gianfar ethernet.2: enabled errata workarounds, flags: 0x4 [ 5.456324] /proc/gfar_eth0_stats created [ 5.506630] fsl-gianfar ethernet.3: enabled errata workarounds, flags: 0x4 [ 5.590173] /proc/gfar_eth1_stats created [ 5.726880] Enabling watchdog on CPU 0 [ 5.726891] Enabling watchdog on CPU 1 [ 5.816757] Masking ICV Error interrupt [ 6.118547] [ 6.118552] Starting Kernel SHA1 KAT ...Starting Kernel HMAC SHA1 FIPS KAT ...Completed Kernel HMAC SHA1 FIPS KAT [ 6.130496] Starting Kernel HMAC SHA256 FIPS KAT ...Completed Kernel HMAC SHA256 FIPS KAT [ 6.131259] Starting Kernel HMAC SHA384 FIPS KAT ...Completed Kernel HMAC SHA384 FIPS KAT [ 6.131789] Starting Kernel HMAC SHA512 FIPS KAT ...Completed Kernel HMAC SHA512 FIPS KAT [ 6.132357] Starting Kernel AES-CBC FIPS KAT ...Completed Kernel AES-CBC FIPS KAT [ 6.165550] Starting Kernel AES-CCM FIPS KAT ...Completed Kernel AES-CCM FIPS KAT [ 6.166017] Starting Kernel 3DES-CBC FIPS KAT ...Completed Kernel 3DES-CBC FIPS KAT [ 6.831165] Completed Kernel SHA1 KAT [ 6.875986] Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT [ 6.983234] Starting Kernel DES KAT ...Completed Kernel DES KAT [ 7.055190] Starting Kernel AES KAT ...Completed Kernel AES KAT [ 7.098990] [ 24.232761] p1020_soc: P1020 Misc Utils Driver version 1 [ 39.724813] init_phy: PHY interface is SGMII [ 39.778880] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 39.854178] ADDRCONF(NETDEV_UP): bond0: link is not ready [ 39.941490] init_phy: PHY interface is SGMII [ 39.995414] bonding: bond0: enslaving eth0 as a backup interface with a down link. [ 40.154056] init_phy: PHY interface is SGMII [ 40.208070] bonding: bond0: enslaving eth1 as a backup interface with a down link. [ 40.537066] AP xml model 86, num_radios 2 (jiffies 20065) [ 40.601688] apType 86 hw_opmode 0 [ 40.641294] radio 0: band 1 ant 1 max_ssid 16 [ 40.693404] radio 1: band 0 ant 1 max_ssid 16 [ 40.747126] PHY: eth0 (mdio@ffe24000:00) - Link is Up - 1000/Full [ 40.820664] init_asap_mod: installation:0 [ 40.868628] ethernet_device_event: dev eth0 registered [ 40.868636] ethernet_device_event: dev eth0 is up [ 40.927597] ethernet_device_event: dev eth0 is changed, carrier: 1 [ 41.011397] firewall cpu: core-1 [ 41.091991] bonding: bond0: link status definitely up for interface eth0. [ 41.173304] bonding: bond0: making interface eth0 the new active one. [ 41.250479] bonding: bond0: first active interface up! [ 41.312230] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready [ 44.876438] Kernel watchdog refresh ended. [ 44.931953] Kernel watchdog refresh ended. [ 50.488061] wl_module_init: msglevel set to 0x1 [ 50.488073] wl_module_init: msglevel2 set to 0x0 [ 50.488080] wl_module_init: emsglevel set to 0x0 [ 50.488086] wl_module_init: phymsglevel set to 0x0 [ 50.488093] wl_module_init: passivemode set to 0x0 [ 50.488100] wl_module_init: txworkq set to 0x0 [ 50.488209] Found chip type AI (0x1513a9c4) [ 50.488343] Chipc: rev 43, caps 0x58680001, chipst 0x9a6d pmurev 17, pmucaps 0x10a22b11 [ 50.492328] Thu Jan 1 00:00:50 1970:1 10.130807 Calibration data check pass. [ 50.496283] Thu Jan 1 00:00:50 1970:2 10.134766 Calibration data check pass. [ 50.496527] HTAVAIL is set, so not updating BBPLL Frequency [ 50.498677] wl0: wlc_attach: Overriding device id: 0x43a2 instead of 0x4360 [ 50.498896] Overriding device id = 0x43a2 [ 50.499032] wl0: wlc_bmac_phy_reset: band not yet set [ 50.499090] wlc_bmac_attach, deviceid 0x43a2 nbands 1 [ 50.499244] wl0: wlc_bmac_phy_reset: band not yet set [ 50.503876] wl0 phy_reg_write: No Clock Reg 173e Write is Not Allowed [ 50.503885] wl0 phy_reg_write: No Clock Reg 1739 Write is Not Allowed [ 50.503893] wl0 phy_reg_write: No Clock Reg 173a Write is Not Allowed [ 50.503900] wl0 phy_reg_write: No Clock Reg 1725 Write is Not Allowed [ 50.503907] wl0 phy_reg_write: No Clock Reg 1729 Write is Not Allowed [ 50.503915] wl0 phy_reg_write: No Clock Reg 1721 Write is Not Allowed [ 50.503922] wl0 phy_reg_write: No Clock Reg 1728 Write is Not Allowed [ 50.503944] wl0 phy_reg_write: No Clock Reg 1720 Write is Not Allowed [ 50.503952] wl0 phy_reg_mod: No Clock Reg 408 Write is Not Allowed [ 50.503959] wl0 phy_reg_write: No Clock Reg 417 Write is Not Allowed [ 50.503966] wl0 phy_reg_write: No Clock Reg 416 Write is Not Allowed [ 50.505084] wl0 phy_reg_mod: No Clock Reg 2e4 Write is Not Allowed [ 50.505091] wl0 phy_reg_write: No Clock Reg 1ec Write is Not Allowed [ 50.505104] wl0: wlc_bmac_attach: chiprev 3 corerev 42 cccap 0x58680001 maccap 0x30518c05 band 5G, phy_type 11 phy_rev 1 [ 50.505376] wl0 phy_reg_write: No Clock Reg 173e Write is Not Allowed [ 50.505384] wl0 phy_reg_write: No Clock Reg 1739 Write is Not Allowed [ 50.505391] wl0 phy_reg_write: No Clock Reg 173a Write is Not Allowed [ 50.505399] wl0 phy_reg_write: No Clock Reg 1725 Write is Not Allowed [ 50.505406] wl0 phy_reg_write: No Clock Reg 1729 Write is Not Allowed [ 50.505413] wl0 phy_reg_write: No Clock Reg 1721 Write is Not Allowed [ 50.505420] wl0 phy_reg_write: No Clock Reg 1728 Write is Not Allowed [ 50.505428] wl0 phy_reg_write: No Clock Reg 1720 Write is Not Allowed [ 50.505435] wl0 phy_reg_mod: No Clock Reg 408 Write is Not Allowed [ 50.505442] wl0 phy_reg_write: No Clock Reg 417 Write is Not Allowed [ 50.505449] wl0 phy_reg_write: No Clock Reg 416 Write is Not Allowed [ 50.505639] wl0: wlc_stf_txcore_shmem_write: No clock [ 50.505778] wl0: wlc_ampdu_tx_set: AGG Mode = MAC+AQM txmaxpkts 1024 [ 50.505787] wl0: wlc_ampdu_tx_set: 0x0, err 0 [ 50.507299] wl0: online cpus 2 [ 50.508743] wifi0: AP type AP-228, radio 0, max_bssids 16 [ 50.576035] wlc_phy_cal_init_acphy: NOT Implemented [ 50.604547] wl0: wlc_set_home_chanspec: Bad channel 34 [ 50.893402] wifi0: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.54_e1.2.2.4.10 (r425351 WLTEST) [ 50.893412] (Compiled in . at 00:36:28 on Oct 7 2017) [ 50.893417] [ 50.893554] Found chip type AI (0x1513a9c4) [ 50.893689] Chipc: rev 43, caps 0x58680001, chipst 0x9a6d pmurev 17, pmucaps 0x10a22b11 [ 50.897696] Thu Jan 1 00:00:50 1970:3 10.536174 Calibration data check pass. [ 50.901645] Thu Jan 1 00:00:50 1970:4 10.540128 Calibration data check pass. [ 50.901889] HTAVAIL is set, so not updating BBPLL Frequency [ 50.904025] wl1: wlc_attach: Overriding device id: 0x43a1 instead of 0x4360 [ 50.904244] Overriding device id = 0x43a1 [ 50.904379] wl1: wlc_bmac_phy_reset: band not yet set [ 50.904451] wlc_bmac_attach, deviceid 0x43a1 nbands 1 [ 50.904606] wl1: wlc_bmac_phy_reset: band not yet set [ 50.908941] wl1 phy_reg_write: No Clock Reg 173e Write is Not Allowed [ 50.908951] wl1 phy_reg_write: No Clock Reg 1739 Write is Not Allowed [ 50.908958] wl1 phy_reg_write: No Clock Reg 173a Write is Not Allowed [ 50.908966] wl1 phy_reg_write: No Clock Reg 1725 Write is Not Allowed [ 50.908973] wl1 phy_reg_write: No Clock Reg 1729 Write is Not Allowed [ 50.908980] wl1 phy_reg_write: No Clock Reg 1721 Write is Not Allowed [ 50.908988] wl1 phy_reg_write: No Clock Reg 1728 Write is Not Allowed [ 50.908995] wl1 phy_reg_write: No Clock Reg 1720 Write is Not Allowed [ 50.909003] wl1 phy_reg_mod: No Clock Reg 408 Write is Not Allowed [ 50.909010] wl1 phy_reg_write: No Clock Reg 417 Write is Not Allowed [ 50.909017] wl1 phy_reg_write: No Clock Reg 416 Write is Not Allowed [ 50.910131] wl1 phy_reg_mod: No Clock Reg 2e4 Write is Not Allowed [ 50.910138] wl1 phy_reg_write: No Clock Reg 1ec Write is Not Allowed [ 50.910151] wl1: wlc_bmac_attach: chiprev 3 corerev 42 cccap 0x58680001 maccap 0x30518c05 band 2.4G, phy_type 11 phy_rev 1 [ 50.910421] wl1 phy_reg_write: No Clock Reg 173e Write is Not Allowed [ 50.910429] wl1 phy_reg_write: No Clock Reg 1739 Write is Not Allowed [ 50.910455] wl1 phy_reg_write: No Clock Reg 173a Write is Not Allowed [ 50.910462] wl1 phy_reg_write: No Clock Reg 1725 Write is Not Allowed [ 50.910470] wl1 phy_reg_write: No Clock Reg 1729 Write is Not Allowed [ 50.910477] wl1 phy_reg_write: No Clock Reg 1721 Write is Not Allowed [ 50.910484] wl1 phy_reg_write: No Clock Reg 1728 Write is Not Allowed [ 50.910492] wl1 phy_reg_write: No Clock Reg 1720 Write is Not Allowed [ 50.910499] wl1 phy_reg_mod: No Clock Reg 408 Write is Not Allowed [ 50.910506] wl1 phy_reg_write: No Clock Reg 417 Write is Not Allowed [ 50.910513] wl1 phy_reg_write: No Clock Reg 416 Write is Not Allowed [ 50.910710] wl1: wlc_stf_txcore_shmem_write: No clock [ 50.910836] wl1: wlc_ampdu_tx_set: AGG Mode = MAC+AQM txmaxpkts 1024 [ 50.910845] wl1: wlc_ampdu_tx_set: 0x0, err 0 [ 50.911987] wl1: online cpus 2 [ 50.913519] wifi1: AP type AP-228, radio 1, max_bssids 16 [ 50.980790] wlc_phy_cal_init_acphy: NOT Implemented [ 51.008868] wl1: wlc_set_home_chanspec: Bad channel 1 [ 51.043701] wifi1: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.54_e1.2.2.4.10 (r425351 WLTEST) [ 51.043711] (Compiled in . at 00:36:28 on Oct 7 2017) [ 51.043716] [ 51.783940] bond0: no IPv6 routers present [ 55.048442] br0: no IPv6 routers present [ 55.094437] Kernel watchdog refresh ended. [ 107.383493] Wed Nov 22 16:37:47 2017:5 0.000000 wl0 set max_distance 0, radio type 0, outdoor_ap 0, [ 107.383513] Wed Nov 22 16:37:47 2017:6 0.000031 wl0 apply max distance 0(not mesh radio) [ 111.390153] Wed Nov 22 16:37:51 2017:7 4.006660 wifi0: Country Code set to DE [ 111.390180] Wed Nov 22 16:37:51 2017:8 4.006699 wifi0: VHT Mode Enabled [ 111.390253] Wed Nov 22 16:37:51 2017:9 4.006772 wifi0: Beacon Interval 100 [ 111.390269] Wed Nov 22 16:37:51 2017:10 4.006788 wifi0: HT Mode Enabled [ 111.390295] Wed Nov 22 16:37:51 2017:11 4.006812 wifi0: Effective External Antenna Gain set to 2.0 (connector loss 1.0) [ 111.452230] Wed Nov 22 16:37:51 2017:12 4.068738 wifi0: CDD Override is set to 0 [ 111.452248] Wed Nov 22 16:37:51 2017:13 4.068769 wifi0: txbf is enabled [ 111.452266] Wed Nov 22 16:37:51 2017:14 4.068785 wifi0: Energy Detect Threshold (EDT) set to -65dBm [ 111.452989] Wed Nov 22 16:37:51 2017:15 4.069506 wifi0: User EIRP:15.0 Actual EIRP:-32.0 Max EIRP:-32.0 Min EIRP:1.7 [ 112.393498] Wed Nov 22 16:37:52 2017:16 5.010001 wl1 set max_distance 0, radio type 0, outdoor_ap 0, [ 112.393518] Wed Nov 22 16:37:52 2017:17 5.010033 wl1 apply max distance 0(not mesh radio) [ 116.400136] Wed Nov 22 16:37:56 2017:18 9.016643 wifi1: Country Code set to DE [ 116.400155] Wed Nov 22 16:37:56 2017:19 9.016674 wifi1: Beacon Interval 100 [ 116.400179] Wed Nov 22 16:37:56 2017:20 9.016699 wifi1: HT Mode Enabled [ 116.400214] Wed Nov 22 16:37:56 2017:21 9.016733 (null): VHT Supported Rate set to 1023 [ 116.400248] Wed Nov 22 16:37:56 2017:22 9.016766 wifi1: Effective External Antenna Gain set to 2.5 (connector loss 0.5) [ 116.457145] Wed Nov 22 16:37:56 2017:23 9.073653 wifi1: 40MHz Intolerant set to 0 [ 116.457208] Wed Nov 22 16:37:56 2017:24 9.073728 wifi1: CDD Override is set to 0 [ 116.457223] Wed Nov 22 16:37:56 2017:25 9.073744 wifi1: txbf is enabled [ 116.457241] Wed Nov 22 16:37:56 2017:26 9.073760 wifi1: Energy Detect Threshold (EDT) set to -65dBm [ 116.458574] Wed Nov 22 16:37:56 2017:27 9.075088 wifi1: User EIRP:15.0 Actual EIRP:15.0 Max EIRP:17.7 Min EIRP:-2.5 [ 231.317962] Shutting down eth1 due to insufficient POE voltage [power profile 2] [59657.757958] PHY: eth0 (mdio@ffe24000:00) - Link is Down [59657.762069] ethernet_device_event: dev eth0 is changed, carrier: 0 [59658.141961] bonding: bond0: link status definitely down for interface eth0, disabling it [59658.141998] bonding: bond0: now running without any active interface ! [59681.394265] PHY: eth0 (mdio@ffe24000:00) - Link is Up - 1000/Full [59681.394478] ethernet_device_event: dev eth0 is changed, carrier: 1 [59681.741964] bonding: bond0: link status definitely up for interface eth0. [59681.741978] bonding: bond0: making interface eth0 the new active one. [59681.742094] bonding: bond0: first active interface up! [59683.004739] asap_gre_ipv4_err: Received ICMP (DEST_UNREACH, PROT_UNREACH) from 172.30.1.248 for heartbeat tunnel. [59684.007079] asap_gre_ipv4_err: Received ICMP (DEST_UNREACH, PROT_UNREACH) from 172.30.1.248 for heartbeat tunnel. [59685.008665] asap_gre_ipv4_err: Received ICMP (DEST_UNREACH, PROT_UNREACH) from 172.30.1.248 for heartbeat tunnel. [59686.011122] asap_gre_ipv4_err: Received ICMP (DEST_UNREACH, PROT_UNREACH) from 172.30.1.248 for heartbeat tunnel. [59687.013177] asap_gre_ipv4_err: Received ICMP (DEST_UNREACH, PROT_UNREACH) from 172.30.1.248 for heartbeat tunnel. [59688.014621] asap_gre_ipv4_err: Received ICMP (DEST_UNREACH, PROT_UNREACH) from 172.30.1.248 for heartbeat tunnel. [59691.345954] Thu Nov 23 09:10:50 2017:28 59583.784541 wl0 set max_distance 0, radio type 0, outdoor_ap 0, [59691.345973] Thu Nov 23 09:10:50 2017:29 59583.784589 wl0 apply max distance 0(not mesh radio) [59691.405620] Thu Nov 23 09:10:50 2017:30 59583.844222 wl1 set max_distance 0, radio type 0, outdoor_ap 0, [59691.405639] Thu Nov 23 09:10:50 2017:31 59583.844255 wl1 apply max distance 0(not mesh radio) Driver Log -------------------------------------------------------- Current Log Level 3 Log Counter 32 Timestamp 95507.146195 1 10.130807 Calibration data check pass. 2 10.134766 Calibration data check pass. 3 10.536174 Calibration data check pass. 4 10.540128 Calibration data check pass. 5 0.000000 wl0 set max_distance 0, radio type 0, outdoor_ap 0, 6 0.000031 wl0 apply max distance 0(not mesh radio) 7 4.006660 wifi0: Country Code set to DE 8 4.006699 wifi0: VHT Mode Enabled 9 4.006772 wifi0: Beacon Interval 100 10 4.006788 wifi0: HT Mode Enabled 11 4.006812 wifi0: Effective External Antenna Gain set to 2.0 (connector loss 1.0) 12 4.068738 wifi0: CDD Override is set to 0 13 4.068769 wifi0: txbf is enabled 14 4.068785 wifi0: Energy Detect Threshold (EDT) set to -65dBm 15 4.069506 wifi0: User EIRP:15.0 Actual EIRP:-32.0 Max EIRP:-32.0 Min EIRP:1.7 16 5.010001 wl1 set max_distance 0, radio type 0, outdoor_ap 0, 17 5.010033 wl1 apply max distance 0(not mesh radio) 18 9.016643 wifi1: Country Code set to DE 19 9.016674 wifi1: Beacon Interval 100 20 9.016699 wifi1: HT Mode Enabled 21 9.016733 (null): VHT Supported Rate set to 1023 22 9.016766 wifi1: Effective External Antenna Gain set to 2.5 (connector loss 0.5) 23 9.073653 wifi1: 40MHz Intolerant set to 0 24 9.073728 wifi1: CDD Override is set to 0 25 9.073744 wifi1: txbf is enabled 26 9.073760 wifi1: Energy Detect Threshold (EDT) set to -65dBm 27 9.075088 wifi1: User EIRP:15.0 Actual EIRP:15.0 Max EIRP:17.7 Min EIRP:-2.5 28 59583.784541 wl0 set max_distance 0, radio type 0, outdoor_ap 0, 29 59583.784589 wl0 apply max distance 0(not mesh radio) 30 59583.844222 wl1 set max_distance 0, radio type 0, outdoor_ap 0, 31 59583.844255 wl1 apply max distance 0(not mesh radio) (Aruba7210_Master_20) # (Aruba7210_Master_20) #