X4 SPI boot... SF: Detected MX25L3205D with page size 64 kB, total 4 MB SF: Detected MX25L3205D with page size 64 kB, total 4 MB Loading second stage boot loader ................................................................................................. APBoot 1.5.4.9 (build 61851) Built: 2017-10-11 at 14:36:15 CPU0: T1024E, Version: 1.0, (0x85480010) Core: e5500, Version: 2.1, (0x80241021) Single Source Clock Configuration Clock Configuration: CPU0:1200 MHz, CPU1:1200 MHz, CCB:400 MHz, DDR:800 MHz (1600 MT/s data rate) (Asynchronous), IFC:100 MHz FMAN1: 600 MHz QMAN: 400 MHz L1: D-cache 32 KiB enabled I-cache 32 KiB enabled Reset Configuration Word (RCW): 00000000: 0810000c 00000000 00000000 00000000 00000010: 4c800003 80000012 5c027000 21000000 00000020: 00000000 00000000 00000000 00031000 00000030: 00000000 44260a08 00000000 00000006 Board: AP-33x I2C: ready SPI: ready DRAM: 512 MB (DDR3, 32-bit, CL=11, ECC off) Testing 0x00000000 - 0x1fffffff POST1: memory passed Flash: SF: Detected MX25L3205D with page size 64 kB, total 4 MB L2: 256 kB enabled Corenet Platform Cache: 256 kB enabled Using SERDES1 Protocol: 153 (0x99) NAND: 128 MiB PCIe1: RC, link up, x1, speed 5 GT/s dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 168c 0046 00002 00 e0000004 00000000 00000000 00000000 PCIe2: disabled PCIe3: RC, link up, x1, speed 2.5 GT/s dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 168c 0046 00002 00 e0000004 00000000 00000000 00000000 Power: 802.3af POE Volume aos0 has been created Volume aos1 has been created Volume ubifs has been created Net: SF: Detected MX25L3205D with page size 64 kB, total 4 MB Fman1: Uploading microcode version 108.4.10 eth0, eth1 FIPS: passed Hit to stop autoboot: 0 Checking image @ 0x0 Copying image from 0x08000000 Image is signed; verifying checksum... passed SHA2 Signature available Signer Cert OK Policy Cert OK RSA signature verified using SHA2. [ 0.000000] [ 0.000000] Aruba Networks [ 0.000000] ArubaOS Version 8.6.0.11 (build 80920 / label #80920) [ 0.000000] Built by p4build@pr-hpn-build10 on 2021-07-26 at 17:28:54 UTC (gcc version 4.8.1) [ 5.866690] Starting Kernel SHA1 KAT ... [ 5.913617] Completed Kernel SHA1 KAT [ 5.960523] Starting Kernel HMAC-SHA1 KAT ... [ 6.012103] Starting Kernel DES KAT ...[ 6.058037] Completed Kernel DES KAT [ 6.101838] Starting Kernel AES KAT ... [ 6.145635] Completed Kernel AES KAT [ 6.145635] [ 6.209930] Starting Kernel AESGCM KAT ... [ 6.256847] Completed Kernel AESGCM KAT grep: /tmp/ap-info: No such file or di[ 6.315686] Completed Kernel HMAC-SHA1 KAT rectory Populate AP type info AP-type has_ble_support: ONBOARD. Domain Name: arubanetworks.com CMDLINE_WRITE_ENVIRONMENT arg {num_reboot=2} No panic info available Writing /dev/ttyS01 into /tmp/ble_port Enabling ble_daemon via nanny x4: Start hotplug Ethernet port 1 mode: active-standby [ 11.906580] cpu0/0: > WARNING (FM-Port) [CPU00, drivers/net/ethernet/freescale/fman/Peripherals/FM/Port/fm_port.c:3554 FM_PORT_Disable]: [ 12.052458] cpu0/0: FM-0-port-10g-TX-0: BMI or QMI is Busy. Port forced down[ 12.136913] cpu0/0: [ 12.601758] uol: module license 'Proprietary' taints kernel. [ 12.669536] Disabling lock debugging due to kernel taint set device anul0 mtu to 2000 Starting watchdog process... Aruba watchdog daemon started [1 thread(s)] LLDP not sent yet, DHCP is waiting Starting DHCP net.ipv4.conf.all.arp_notify = 1 Getting an IP address... Not LACP mode, adding 30 seconds updelay! Not LACP mode, adding 30 seconds updelay! Not LACP mode, adding 30 seconds updelay! net.ipv4.conf.all.arp_notify = 0 net.ipv4.conf.br0.arp_notify = 1 172.17.171.58 255.255.255.0 172.17.171.1 Running ADP...Done. Master is 172.18.200.10 AP rebooted due to loss power shutting down watchdog process (nanny will restart it)... <<<<< Welcome to the Access Point >>>>> password: