The system is going down NOW !! Sending SIGTERM to all processes. Please stand by while rebooting the system. [ 766.301833] Restarting system. APBoot 1.5.6.3 (build 62050) Built: 2017-10-26 at 10:17:23 Model: AP-27x CPU0: P1020E, Version: 1.1, (0x80ec0011) Core: E500, Version: 5.1, (0x80212051) Clock: CPU0: 800 MHz CPU1: 800 MHz CCB: 400 MHz DDR: 333.333 MHz (666.667 MT/s data rate) (Asynchronous) LBC: 25 MHz L1: D-cache 32KB enabled I-cache 32KB enabled I2C: ready DRAM: Configuring DDR for 666.667 MT/s data rate DDR: 512 MB (DDR3, 32-bit, CL=5, ECC off) POST1: memory passed Flash: 32 MB L2: 256 KB enabled Power: 802.3af POE PCIe1: RC, link up, x1 dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 14e4 4360 00002 03 80000004 00000000 00000000 00000000 PCIe2: RC, link up, x1 dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 14e4 4360 00002 03 a0000004 00000000 00000000 00000000 Net: eth0, eth1 Radio: bcm43460#0, bcm43460#1 FIPS: passed Hit to stop autoboot: 0 Checking image @ 0xee000000 Copying image from 0xee000000 Image is signed; verifying checksum... passed SHA2 Signature available Signer Cert OK Policy Cert OK RSA signature verified using SHA2. [ 0.000000] Flash variant: default [ 0.000000] [ 0.000000] Aruba Networks [ 0.000000] ArubaOS Version 6.5.4.8 (build 65873 / label #65873) [ 0.000000] Built by p4build@pr-hpn-build09 on 2018-07-20 at 04:58:27 UTC (gcc version 4.5.1) [ 0.000000] [ 0.000000] Memory: 508524k/524288k available (10076k kernel code, 15764k reserved, 612k data, 376k bss, 6536k init) [ 0.003032] Processor 1 found. [ 0.124038] Brought up 2 CPUs [ 0.201243] PCI: Probing PCI hardware [ 0.244400] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.307396] pci 0001:02:00.0: PCI bridge to [bus 03-ff] [ 0.369621] pci 0000:00:00.0: enabling device (0106 -> 0107) [ 0.436702] pci 0001:02:00.0: enabling device (0106 -> 0107) [ 5.221675] ee000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank [ 5.296709] Amd/Fujitsu Extended Query Table at 0x0040 [ 5.358228] number of CFI chips: 1 [ 5.412850] fsl-gianfar ethernet.2: enabled errata workarounds, flags: 0x 4 [ 5.496402] /proc/gfar_eth0_stats created [ 5.546684] fsl-gianfar ethernet.3: enabled errata workarounds, flags: 0x 4 [ 5.630245] /proc/gfar_eth1_stats created [ 5.766844] Enabling watchdog on CPU 0 [ 5.766854] Enabling watchdog on CPU 1 [ 5.856705] Masking ICV Error interrupt [ 6.158358] [ 6.158363] Starting Kernel SHA1 KAT ...Starting Kernel HMAC SHA1 FIPS KA T ...Completed Kernel HMAC SHA1 FIPS KAT [ 6.167542] Starting Kernel HMAC SHA256 FIPS KAT ...Completed Kernel HMAC SHA256 FIPS KAT [ 6.168281] Starting Kernel HMAC SHA384 FIPS KAT ...Completed Kernel HMAC SHA384 FIPS KAT [ 6.168800] Starting Kernel HMAC SHA512 FIPS KAT ...Completed Kernel HMAC SHA512 FIPS KAT [ 6.169370] Starting Kernel AES-CBC FIPS KAT ...Completed Kernel AES-CBC FIPS KAT [ 6.202552] Starting Kernel AES-CCM FIPS KAT ...Completed Kernel AES-CCM FIPS KAT [ 6.203012] Starting Kernel 3DES-CBC FIPS KAT ...Completed Kernel 3DES-CB C FIPS KAT [ 6.870996] Completed Kernel SHA1 KAT [ 6.915815] Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 K AT [ 7.022990] Starting Kernel DES KAT ...Completed Kernel DES KAT [ 7.094940] Starting Kernel AES KAT ...Completed Kernel AES KAT [ 7.138733] Domain Name: arubanetworks.com No panic info available ardmore: Start hotplug [ 24.315043] p1020_soc: P1020 Misc Utils Driver version 1 Ethernet port 1 mode: active-standby [ 39.825037] init_phy: PHY interface is SGMII [ 39.920230] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 39.995547] ADDRCONF(NETDEV_UP): bond0: link is not ready [ 40.084753] init_phy: PHY interface is SGMII [ 40.138745] bonding: bond0: enslaving eth0 as a backup interface with a d own link. [ 40.297242] init_phy: PHY interface is SGMII [ 40.351408] bonding: bond0: enslaving eth1 as a backup interface with a d own link. [ 40.693504] AP xml model 86, num_radios 2 (jiffies 20140) [ 40.758181] apType 86 hw_opmode 0 [ 40.797850] radio 0: band 1 ant 1 max_ssid 16 [ 40.850012] radio 1: band 0 ant 1 max_ssid 16 [ 40.851714] PHY: eth0 (mdio@ffe24000:00) - Link is Up - 1000/Full [ 40.851874] bonding: bond0: link status definitely up for interface eth0. [ 40.851883] bonding: bond0: making interface eth0 the new active one. [ 40.851922] bonding: bond0: first active interface up! [ 40.852451] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready [ 41.278703] init_asap_mod: installation:0 [ 41.326699] ethernet_device_event: dev eth0 is up [ 41.469670] bond0: IPv6 duplicate address fe80::924c:81ff:fecf:b572 detec ted! [ 41.770665] firewall cpu: core-1 Starting watchdog process... LLDP not sent yet, DHCP is waiting LLDP not sent yet, DHCP is waiting Starting DHCP net.ipv4.conf.all.arp_notify = 1 Getting an IP address... net.ipv4.conf.all.arp_notify = 0 net.ipv4.conf.br0.arp_notify = 1 192.168.151.117 255.255.255.0 192.168.151.1 Running ADP...Done. Master is 192.168.151.111 [ 53.852555] wifi0: AP type AP-228, radio 0, max_bssids 16 [ 54.297718] wifi1: AP type AP-228, radio 1, max_bssids 16 Clearing P1020 PCIe Error Status AP rebooted Sun May 12 13:01:56 GMT 2019; SAPD: Rebooting after provisioning shutting down watchdog process (nanny will restart it)... <<<<< Welcome to the Access Point >>>>>