show tech-support and show tech-support APBoot 2.1.3.4 (build 56756) Built: 2016-10-05 at 10:14:25 Model: AP-30x DRAM: 512 MiB Flash: Detected MX25R3235F: total 4 MiB NAND: 128 MiB PCIE0 link up dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 168c 0040 00002 00 00000004 00000000 00000000 00000000 Power: 802.3at POE Net: eth0 Radio: qca9990#0, ipq4029#1 Reset: cold **** Configuration Reset Requested by User **** Clearing state... Checking OS image and flags Invalid image format version: 0x0 Continuing with OS clear 512 bytes written to volume aos0 Erasing flash sector @ 0x3a0000... OK Erasing UBIFS ...OK done Purging environment... preserving os_partition (0) Erasing SPI flash...Writing to SPI flash...done Erasing SPI flash...Writing to SPI flash...done FIPS: passed Hit to stop autoboot: 0 apboot> purgeenv preserving os_partition (0) Erasing SPI flash...Writing to SPI flash...done Erasing SPI flash...Writing to SPI flash...done apboot> clear os 512 bytes written to volume aos0 apboot> save Saving Environment to SPI Flash... Erasing SPI flash...Writing to SPI flash...done apboot> factory_reset Clearing state... Checking OS image and flags Invalid image format version: 0x0 Continuing with OS clear 512 bytes written to volume aos0 Erasing UBIFS ...OK done Purging environment... preserving os_partition (0) Erasing SPI flash...Writing to SPI flash...done Erasing SPI flash...Writing to SPI flash...done apboot> boot Booting OS partition 0 Checking image @ 0x0 Invalid image format version: 0x0 Checking image @ 0x2000000 Copying image from 0x84000000 Image is signed; verifying checksum... passed SHA2 Signature available Signer Cert OK Policy Cert OK RSA signature verified using SHA2. Uncompressing Kernel Image ... OK [ 0.000000] [ 0.000000] Alcatel-Lucent [ 0.000000] AOS-W Version 6.5.1.0-4.3.1.0 (build 57768 / label #57768) [ 0.000000] Built by p4build@rhodes on 2016-12-15 at 05:22:33 PST (gcc version 4.6.3) [ 0.000000] [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.024252] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.054799] i2c-gpio driver registered [ 9.654275] 3 ofpart partitions found on MTD device 7980000.qcom,nand [ 9.724678] Creating 3 MTD partitions on "7980000.qcom,nand": [ 9.793418] 0x000000000000-0x000002000000 : "aos0" [ 9.892198] 0x000002000000-0x000004000000 : "aos1" [ 9.978404] 0x000004000000-0x000008000000 : "ubifs" [ 10.110695] m25p80 spi0.0: found mx25r3235f, expected n25q128a11 [ 10.194875] Found AT97SC3203 on i2c_1.8 [ 10.233808] Key type dns_resolver registered [ 10.279375] Registering SWP/SWPB emulation handler [ 11.746176] Starting Kernel SHA1 KAT ... [ 11.780633] Completed Kernel SHA1 KAT [ 11.827514] Starting Kernel HMAC-SHA1 KAT ... [ 11.877657] Starting Kernel DES KAT ...[ 11.923467] Completed Kernel DES KAT [ 11.967107] Starting Kernel AES KAT ... [ 12.010894] Completed Kernel AES KAT [ 12.010894] [ 12.074481] Starting Kernel AESGCM KAT ... [ 12.121230] Completed Kernel AESGCM KAT [ 12.170517] Completed Kernel HMAC-SHA1 KAT Thu Jan 1 00:00:00 PST 1970 Domain Name: instant.alcatel-lucent.com Current OEM Name : Alcatel-Lucent Disabling ipv6 for devices by default AP-type has_ble_support: ONBOARD. IPv6 capability is supported for devices No panic info available Writing /dev/ttyMSM1 into /tmp/ble_port Enabling ble_daemon and ble_relay via nanny apfcutil: sector CACHE: Cache uninitialized apfcutil: sector RAP: Cache uninitialized apfcutil: sector FAT: Cache uninitialized apfcutil: sector SCRATCH: Cache uninitialized Backup ENV. apfcutil: sector MESH Prov: Cache uninitialized [ 20.668216] bus_scale_table is NULL [ 20.702881] sps:Pipe 3 already allocated on BAM 0x08e04000 [ 20.763081] sps:Failed to allocate connection [ 20.813058] sps:Fail to allocate resource for BAM 0x (null) pipe 0. [ 20.891194] QCE50: qce_sps_init_ep_conn: sps_connect() fail pipe_handle=0xd96e5200, rc = -1 [ 20.991290] qcrypto: probe of 8e20000.qcrypto failed with error -1 Installing glenmorangie ethernet driver [ 21.320288] edma module_init [ 21.495091] mtd va is d96c9c30 [ 21.549145] isl28022: Found i2c_1.8 Starting watchdog process... Cfg len is 0 Configuration file is empty, turning on default services... extended ssid activate due to no AP config ... touching file /tmp/ip_mode_0 eth1 admin down SIOCGIFFLAGS: No such device init usb modem ... [ 22.264162] PPP generic driver version 2.4.2 [ 22.402328] usbcore: registered new interface driver usbserial [ 22.459792] usbcore: registered new interface driver usbserial_generic [ 22.537870] usbserial: USB Serial support registered for generic [ 22.654589] SCSI subsystem initialized [ 22.853023] usbcore: registered new interface driver usb-storage No USB Plugged in [ 43.070938] usbcore: deregistering interface driver usb-storage [ 43.143935] cdrom: Uniform CD-ROM driver unloaded [ 43.200290] usbserial: USB Serial deregistering driver generic [ 43.257813] usbcore: deregistering interface driver usbserial_generic [ 43.334857] usbcore: deregistering interface driver usbserial [ 45.956454] IPv6: ADDRCONF(NETDEV_UP): bond0: link is not ready [ 46.404749] bond0: GMAC Link is up with phy_speed=1000 [ 46.453802] IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready Mesh is DISABLED on this device. copying bootuplog ... [ 47.370828] drvlog_mod: module license 'Proprietary' taints kernel. [ 47.447142] Disabling lock debugging due to kernel taint [ 47.552385] AP xml model 98, num_radios 2 (jiffies 23774) [ 47.604535] init_asap_mod: installation:0 [ 47.652442] radio 0: band 1 ant 0 max_ssid 16 [ 47.704521] radio 1: band 0 ant 0 max_ssid 16 [ 47.756627] election init: rand=e HZ=500 [ 47.803477] IAP client match init allow PAPI notify asap_mod 3g no present... apdot1x authentication is not enabled Getting an IP address... Jan 1 00:00:35 udhcpc[1805]: udhcpc (v0.9.9-pre) started Jan 1 00:00:35 udhcpc[1805]: send_discover: pkt num 0, secs 0 Jan 1 00:00:35 udhcpc[1805]: Sending discover... Jan 1 00:00:36 udhcpc[1805]: send_selecting: pkt num 0, secs 0 Jan 1 00:00:36 udhcpc[1805]: Sending select for 172.16.255.152... Jan 1 00:00:36 udhcpc[1805]: Lease of 172.16.255.152 obtained, lease time 9000 Jan 1 00:00:36 udhcpc[1805]: DHCP OPT 43, len: 12, buf: 161.111.84.4 Jan 1 00:00:36 udhcpc[1805]: DHCP OPT 60 does not match ArubaInstantAP, delete airwave config 172.16.255.152 255.255.0.0 172.16.255.3 Compressing all files in the /etc/httpd directory... [ 52.819508] ip_time_handler: Got ip and packets on bond0 Started master election 11-0, rand 27 Done. Starting Webserver bind: Transport endpoint is not connected bind: Transport endpoint is not connected bind: Transport endpoint is not connected bind: Transport endpoint is not connected Launching NTP Client on pool.ntp.org [ 55.484428] ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D) [ 55.550029] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 55.661740] ath_dfs: Version 2.0.0 [ 55.661740] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 55.804621] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 55.928592] ath_pci: (Atheros/multi-bss) [ 55.964213] PCI: enabling device 0000:00:00.0 (0144 -> 0147) [ 56.031787] PCI: enabling device 0000:01:00.0 (0140 -> 0142) [ 56.100355] ath_pci 0000:01:00.0: ath DEBUG: sc=0xd9759000 [ 57.411945] Startup Mode-0 set [ 57.436610] htt_peer_map_timer_init Enter pdev d9b08000 hrtimer d9b0a960 [ 57.516171] [ 57.516171] htt_alloc_peer_map_mem : Alloc Success : host q vaddr de42b000 paddr 9e42b000 [ 57.632839] [ 57.632839] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 57.736827] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d9020000 [ 57.830924] [ 57.830924] SERIAL NUMBER: : wifi0 [ 57.830924] [ 57.905766] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 58.058469] wmi_ready_event_rx: WMI UNIFIED READY event [ 58.110719] target uses HTT version 2.2; host uses 2.2 [ 58.277116] ol_ath_smart_ant_attach: Firmware doest not support Smart Antenna. [ 58.351138] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. [ 58.437721] dfs_attach: event log disabled by default [ 58.502675] aruba_mods_radio_attach: dev: ic:c0c805c0 osdev:d9759010 phy:2 [ 58.587665] wifi0: Base BSSID 34:fc:b9:36:19:d0, 16 available BSSID(s) processor ID: 0 [ 58.682375] bond0 address=34:fc:b9:cb:61:9c [ 58.732371] br0 address=34:fc:b9:cb:61:9c [ 58.780298] wifi0: AP type AP-305, radio 0, max_bssids 16 [ 58.844992] Resetting spectral chainmask to Rx chainmask [ 58.908444] mtd va is d96c9c30 [ 58.975151] Resetting spectral chainmask to Rx chainmask [ 59.026862] Init the PCAP for radio0 offload 1. [ 59.083830] aruba_mods_radio_attach: radio: 0, init txq work cpu: core-2 [ 59.160941] skipping 5G radio with core-id 1 [ 59.211741] ol_ath_ahb_probe [ 59.246111] ol_ath_ahb_probe: io resource start: 0xa000000, mem=0xe5c00000 [ 59.328345] *********** Dakota ************* [ 59.381164] ol_ath_ahb_configure: MSI addr: 0b006040, MSI base: 00000040 [ 59.460777] Wifi0 CPU frequency 250000000 [ 59.509740] ath9k a000000.wifi: ath DEBUG: sc=0xdca48800 [ 59.573123] [ 59.573123] ol_ath_ahb_configure : num_desired MSI set to 0 [ 59.658582] [ 59.658582] Using Legacy Interrupt [ 59.717910] [ 59.717910] Waiting for target init [ 59.778339] [ 59.778339] Done waiting [ 61.146548] Startup Mode-0 set [ 61.171232] htt_peer_map_timer_init Enter pdev d8df0000 hrtimer d8df2960 [ 61.250783] [ 61.250783] htt_alloc_peer_map_mem : Alloc Success : host q vaddr d9012000 paddr 99012000 [ 61.367520] [ 61.367520] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 61.471550] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d88c0000 [ 61.565591] [ 61.565591] SERIAL NUMBER: : wifi1 [ 61.565591] [ 61.640383] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 61.764081] wmi_ready_event_rx: WMI UNIFIED READY event [ 61.816337] target uses HTT version 2.2; host uses 2.2 [ 61.826282] ol_ath_smart_ant_attach: Firmware doest not support Smart Antenna. [ 61.826286] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. [ 61.826344] dfs_attach: event log disabled by default [ 61.829585] aruba_mods_radio_attach: dev: ic:d93005c0 osdev:dca48810 phy:2 [ 61.829612] wifi1: Base BSSID 34:fc:b9:36:19:c0, 16 available BSSID(s) processor ID: 0 [ 61.829620] bond0 address=34:fc:b9:cb:61:9c [ 61.829628] br0 address=34:fc:b9:cb:61:9c [ 61.829633] wifi1: AP type AP-305, radio 1, max_bssids 16 [ 61.829664] Resetting spectral chainmask to Rx chainmask [ 61.829669] Resetting spectral chainmask to Rx chainmask [ 61.830075] Init the PCAP for radio1 offload 1. [ 61.833425] aruba_mods_radio_attach: radio: 1, init txq work cpu: core-2 [ 62.723729] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 [ 62.805860] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 AP rebooted caused by cold HW reset(power loss) shutting down watchdog process (nanny will restart it)... <<<<< Welcome to the Access Point >>>>> Completed SW FIPS KAT test User: admin System uptime is 70 seconds and CLI is not ready yet, please try again later. User: [ 84.005434] i am master now [ 84.026341] (08:01:11) !!! Init ---> Master [ 84.076355] asap_send_elected_master: sent successfully User: admin Password: show tech-support and show tech-support supplemental are the two most useful outputs to collect for any kind of troubleshooting session. 34:fc:b9:cb:61:9c# enable 34:fc:b9:cb:61:9c# convert-aos-ap cap 172.16.255.[ 162.518641] VAP device aruba100 created osifp: (de6aa5c0) os_if: (da5d8000) convert-aos-ap cap 172.16.255.10 Converting to Controller based AP. Will automatically reboot when done. 34:fc:b9:cb:61:9c# The system is going down NOW !! Sending SIGKILL to all processes. Umouting UBIFS completed. Please stand by while rebooting the system. [ 216.907316] reboot: Restarting system APBoot 2.1.3.4 (build 56756) Built: 2016-10-05 at 10:14:25 Model: AP-30x DRAM: 512 MiB Flash: Detected MX25R3235F: total 4 MiB NAND: 128 MiB PCIE0 link up dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 168c 0040 00002 00 00000004 00000000 00000000 00000000 Power: 802.3at POE Net: eth0 Radio: qca9990#0, ipq4029#1 Reset: warm FIPS: passed Hit to stop autoboot: 0 Booting OS partition 0 Checking image @ 0x0 Copying image from 0x84000000 Image is signed; verifying checksum... passed SHA2 Signature available Signer Cert OK Policy Cert OK RSA signature verified using SHA2. Uncompressing Kernel Image ... OK [ 0.000000] [ 0.000000] Alcatel-Lucent [ 0.000000] AOS-W Version 6.5.2.1 (build 59704 / label #59704) [ 0.000000] Built by p4build@pr-hpn-build09 on 2017-05-20 at 05:58:59 UTC (gcc version 4.6.3) [ 0.000000] [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.016614] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.042448] i2c-gpio driver registered [ 5.636321] 3 ofpart partitions found on MTD device 7980000.qcom,nand [ 5.700972] Creating 3 MTD partitions on "7980000.qcom,nand": [ 5.769709] 0x000000000000-0x000002000000 : "aos0" [ 5.868440] 0x000002000000-0x000004000000 : "aos1" [ 5.954588] 0x000004000000-0x000008000000 : "ubifs" [ 6.095835] m25p80 spi0.0: found mx25r3235f, expected n25q128a11 [ 6.233873] Found AT97SC3203 on i2c_1.8 [ 6.272429] Key type dns_resolver registered [ 6.318358] Registering SWP/SWPB emulation handler [ 8.044409] TZ dump found for reboot [ 8.108836] Starting Kernel SHA1 KAT ... [ 8.143289] Completed Kernel SHA1 KAT [ 8.190181] Starting Kernel HMAC-SHA1 KAT ... [ 8.240296] Starting Kernel DES KAT ...[ 8.286044] Completed Kernel DES KAT [ 8.329772] Starting Kernel AES KAT ... [ 8.373540] Completed Kernel AES KAT [ 8.373540] [ 8.437132] Starting Kernel AESGCM KAT ... [ 8.483890] Completed Kernel AESGCM KAT [ 8.533134] Completed Kernel HMAC-SHA1 KAT AP-type has_ble_support: ONBOARD. Domain Name: alcatel-lucent.com No panic info available Writing /dev/ttyMSM1 into /tmp/ble_port Enabling ble_daemon via nanny [ 14.172645] edma module_init [ 14.916096] drvlog_mod: module license 'Proprietary' taints kernel. [ 14.978669] Disabling lock debugging due to kernel taint Starting watchdog process... Getting an IP address... [ 19.216495] bond0: GMAC Link is up with phy_speed=1000 172.16.255.152 255.255.0.0 172.16.255.3 Running ADP...Done. Master is 161.111.84.4 AP rebooted Thu Jan 1 08:03:13 UTC 1970; Image Upgrade Successful shutting down watchdog process (nanny will restart it)... <<<<< Welcome to the Access Point >>>>> ~ # ~ # The system is going down NOW !! Sending SIGTERM to all processes. Sending SIGKILL to all processes. Unmounting UBIFS completed. Please stand by while rebooting the system. [ 330.745257] reboot: Restart APBoot 2.1.3.4 (build 56756) Built: 2016-10-05 at 10:14:25 Model: AP-30x DRAM: 512 MiB Flash: Detected MX25R3235F: total 4 MiB NAND: 128 MiB PCIE0 link up dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 168c 0040 00002 00 00000004 00000000 00000000 00000000 Power: 802.3at POE Net: eth0 Radio: qca9990#0, ipq4029#1 Reset: warm FIPS: passed Hit to stop autoboot: 0 Booting OS partition 0 Checking image @ 0x0 Copying image from 0x84000000 Image is signed; verifying checksum... passed SHA2 Signature available Signer Cert OK Policy Cert OK RSA signature verified using SHA2. Uncompressing Kernel Image ... OK [ 0.000000] [ 0.000000] Alcatel-Lucent [ 0.000000] AOS-W Version 6.5.2.1 (build 59704 / label #59704) [ 0.000000] Built by p4build@pr-hpn-build09 on 2017-05-20 at 05:58:59 UTC (gcc version 4.6.3) [ 0.000000] [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.016574] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.042435] i2c-gpio driver registered [ 5.638962] 3 ofpart partitions found on MTD device 7980000.qcom,nand [ 5.703614] Creating 3 MTD partitions on "7980000.qcom,nand": [ 5.772351] 0x000000000000-0x000002000000 : "aos0" [ 5.871087] 0x000002000000-0x000004000000 : "aos1" [ 5.957262] 0x000004000000-0x000008000000 : "ubifs" [ 6.098639] m25p80 spi0.0: found mx25r3235f, expected n25q128a11 [ 6.236825] Found AT97SC3203 on i2c_1.8 [ 6.275343] Key type dns_resolver registered [ 6.321319] Registering SWP/SWPB emulation handler [ 8.081122] Starting Kernel SHA1 KAT ... [ 8.115582] Completed Kernel SHA1 KAT [ 8.162479] Starting Kernel HMAC-SHA1 KAT ... [ 8.212611] Starting Kernel DES KAT ...[ 8.258334] Completed Kernel DES KAT [ 8.302062] Starting Kernel AES KAT ... [ 8.345842] Completed Kernel AES KAT [ 8.345842] [ 8.409442] Starting Kernel AESGCM KAT ... [ 8.456177] Completed Kernel AESGCM KAT [ 8.505474] Completed Kernel HMAC-SHA1 KAT AP-type has_ble_support: ONBOARD. Domain Name: alcatel-lucent.com No panic info available Writing /dev/ttyMSM1 into /tmp/ble_port Enabling ble_daemon via nanny [ 14.140648] edma module_init [ 14.884278] drvlog_mod: module license 'Proprietary' taints kernel. [ 14.946860] Disabling lock debugging due to kernel taint Starting watchdog process... Getting an IP address... [ 19.184756] bond0: GMAC Link is up with phy_speed=1000 172.16.255.152 255.255.0.0 172.16.255.3 Running ADP...Done. Master is 161.111.84.4 AP rebooted Wed Dec 31 16:05:20 PST 1969; SAPD: Reboot after image upgrade failed: 65280 shutting down watchdog process (nanny will restart it)... <<<<< Welcome to the Access Point >>>>> ~ #