(Aruba7210_Master_20) #show ap debug driver-log ap-name ArubaAP-011 [ 0.000000] Flash variant: default [ 0.000000] [ 0.000000] Aruba Networks [ 0.000000] ArubaOS Version 6.5.4.2 (build 61807 / label #61807) [ 0.000000] Built by p4build@lesbos on 2017-10-07 at 00:39:00 PDT (gcc version 4.5.1) [ 0.000000] [ 0.000000] Memory: 508540k/524288k available (10060k kernel code, 15748k reserved, 612k data, 376k bss, 6520k init) [ 0.000000] time_init: decrementer frequency = 50.000000 MHz [ 0.000000] time_init: processor frequency = 799.999992 MHz [ 0.000000] clockevent: decrementer mult[ccccccc] shift[32] cpu[0] [ 0.002969] Processor 1 found. [ 0.113020] Brought up 2 CPUs [ 0.190215] PCI: Probing PCI hardware [ 0.233368] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.296360] pci 0001:02:00.0: PCI bridge to [bus 03-ff] [ 0.358585] pci 0000:00:00.0: enabling device (0106 -> 0107) [ 0.425678] pci 0001:02:00.0: enabling device (0106 -> 0107) [ 5.183606] ee000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank [ 5.258652] Amd/Fujitsu Extended Query Table at 0x0040 [ 5.320170] number of CFI chips: 1 [ 5.374786] fsl-gianfar ethernet.2: enabled errata workarounds, flags: 0x4 [ 5.458343] /proc/gfar_eth0_stats created [ 5.508634] fsl-gianfar ethernet.3: enabled errata workarounds, flags: 0x4 [ 5.592176] /proc/gfar_eth1_stats created [ 5.729025] Enabling watchdog on CPU 0 [ 5.729036] Enabling watchdog on CPU 1 [ 5.818889] Masking ICV Error interrupt [ 6.120609] [ 6.120614] Starting Kernel SHA1 KAT ...Starting Kernel HMAC SHA1 FIPS KAT ...Completed Kernel HMAC SHA1 FIPS KAT [ 6.132488] Starting Kernel HMAC SHA256 FIPS KAT ...Completed Kernel HMAC SHA256 FIPS KAT [ 6.133255] Starting Kernel HMAC SHA384 FIPS KAT ...Completed Kernel HMAC SHA384 FIPS KAT [ 6.133788] Starting Kernel HMAC SHA512 FIPS KAT ...Completed Kernel HMAC SHA512 FIPS KAT [ 6.134349] Starting Kernel AES-CBC FIPS KAT ...Completed Kernel AES-CBC FIPS KAT [ 6.167566] Starting Kernel AES-CCM FIPS KAT ...Completed Kernel AES-CCM FIPS KAT [ 6.168036] Starting Kernel 3DES-CBC FIPS KAT ...Completed Kernel 3DES-CBC FIPS KAT [ 6.833225] Completed Kernel SHA1 KAT [ 6.878046] Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT [ 6.985282] Starting Kernel DES KAT ...Completed Kernel DES KAT [ 7.057237] Starting Kernel AES KAT ...Completed Kernel AES KAT [ 7.101038] [ 24.246595] p1020_soc: P1020 Misc Utils Driver version 1 [ 39.736626] init_phy: PHY interface is SGMII [ 39.790693] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 39.866015] ADDRCONF(NETDEV_UP): bond0: link is not ready [ 39.953480] init_phy: PHY interface is SGMII [ 40.007531] bonding: bond0: enslaving eth0 as a backup interface with a down link. [ 40.166308] init_phy: PHY interface is SGMII [ 40.220543] bonding: bond0: enslaving eth1 as a backup interface with a down link. [ 40.550269] AP xml model 86, num_radios 2 (jiffies 20072) [ 40.614910] apType 86 hw_opmode 0 [ 40.654516] radio 0: band 1 ant 1 max_ssid 16 [ 40.706620] radio 1: band 0 ant 1 max_ssid 16 [ 40.760339] PHY: eth0 (mdio@ffe24000:00) - Link is Up - 1000/Full [ 40.833879] init_asap_mod: installation:0 [ 40.881842] ethernet_device_event: dev eth0 registered [ 40.881848] ethernet_device_event: dev eth0 is up [ 40.940837] ethernet_device_event: dev eth0 is changed, carrier: 1 [ 41.024640] firewall cpu: core-1 [ 41.063994] bonding: bond0: link status definitely up for interface eth0. [ 41.145319] bonding: bond0: making interface eth0 the new active one. [ 41.222489] bonding: bond0: first active interface up! [ 41.284204] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready [ 44.888446] Kernel watchdog refresh ended. [ 44.939948] Kernel watchdog refresh ended. [ 50.569879] wl_module_init: msglevel set to 0x1 [ 50.569890] wl_module_init: msglevel2 set to 0x0 [ 50.569897] wl_module_init: emsglevel set to 0x0 [ 50.569904] wl_module_init: phymsglevel set to 0x0 [ 50.569911] wl_module_init: passivemode set to 0x0 [ 50.569948] wl_module_init: txworkq set to 0x0 [ 50.570049] Found chip type AI (0x1513a9c4) [ 50.570183] Chipc: rev 43, caps 0x58680001, chipst 0x9a6d pmurev 17, pmucaps 0x10a22b11 [ 50.574166] Thu Jan 1 00:00:50 1970:1 10.199972 Calibration data check pass. [ 50.578120] Thu Jan 1 00:00:50 1970:2 10.203930 Calibration data check pass. [ 50.578365] HTAVAIL is set, so not updating BBPLL Frequency [ 50.580496] wl0: wlc_attach: Overriding device id: 0x43a2 instead of 0x4360 [ 50.580714] Overriding device id = 0x43a2 [ 50.580849] wl0: wlc_bmac_phy_reset: band not yet set [ 50.580908] wlc_bmac_attach, deviceid 0x43a2 nbands 1 [ 50.581063] wl0: wlc_bmac_phy_reset: band not yet set [ 50.585725] wl0 phy_reg_write: No Clock Reg 173e Write is Not Allowed [ 50.585734] wl0 phy_reg_write: No Clock Reg 1739 Write is Not Allowed [ 50.585742] wl0 phy_reg_write: No Clock Reg 173a Write is Not Allowed [ 50.585749] wl0 phy_reg_write: No Clock Reg 1725 Write is Not Allowed [ 50.585756] wl0 phy_reg_write: No Clock Reg 1729 Write is Not Allowed [ 50.585764] wl0 phy_reg_write: No Clock Reg 1721 Write is Not Allowed [ 50.585771] wl0 phy_reg_write: No Clock Reg 1728 Write is Not Allowed [ 50.585778] wl0 phy_reg_write: No Clock Reg 1720 Write is Not Allowed [ 50.585786] wl0 phy_reg_mod: No Clock Reg 408 Write is Not Allowed [ 50.585793] wl0 phy_reg_write: No Clock Reg 417 Write is Not Allowed [ 50.585800] wl0 phy_reg_write: No Clock Reg 416 Write is Not Allowed [ 50.586933] wl0 phy_reg_mod: No Clock Reg 2e4 Write is Not Allowed [ 50.586941] wl0 phy_reg_write: No Clock Reg 1ec Write is Not Allowed [ 50.586953] wl0: wlc_bmac_attach: chiprev 3 corerev 42 cccap 0x58680001 maccap 0x30518c05 band 5G, phy_type 11 phy_rev 1 [ 50.587231] wl0 phy_reg_write: No Clock Reg 173e Write is Not Allowed [ 50.587239] wl0 phy_reg_write: No Clock Reg 1739 Write is Not Allowed [ 50.587247] wl0 phy_reg_write: No Clock Reg 173a Write is Not Allowed [ 50.587254] wl0 phy_reg_write: No Clock Reg 1725 Write is Not Allowed [ 50.587261] wl0 phy_reg_write: No Clock Reg 1729 Write is Not Allowed [ 50.587268] wl0 phy_reg_write: No Clock Reg 1721 Write is Not Allowed [ 50.587276] wl0 phy_reg_write: No Clock Reg 1728 Write is Not Allowed [ 50.587283] wl0 phy_reg_write: No Clock Reg 1720 Write is Not Allowed [ 50.587290] wl0 phy_reg_mod: No Clock Reg 408 Write is Not Allowed [ 50.587297] wl0 phy_reg_write: No Clock Reg 417 Write is Not Allowed [ 50.587304] wl0 phy_reg_write: No Clock Reg 416 Write is Not Allowed [ 50.587494] wl0: wlc_stf_txcore_shmem_write: No clock [ 50.587624] wl0: wlc_ampdu_tx_set: AGG Mode = MAC+AQM txmaxpkts 1024 [ 50.587633] wl0: wlc_ampdu_tx_set: 0x0, err 0 [ 50.589136] wl0: online cpus 2 [ 50.590675] wifi0: AP type AP-228, radio 0, max_bssids 16 [ 50.657958] wlc_phy_cal_init_acphy: NOT Implemented [ 50.686461] wl0: wlc_set_home_chanspec: Bad channel 34 [ 50.975265] wifi0: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.54_e1.2.2.4.10 (r425351 WLTEST) [ 50.975276] (Compiled in . at 00:36:28 on Oct 7 2017) [ 50.975280] [ 50.975419] Found chip type AI (0x1513a9c4) [ 50.975555] Chipc: rev 43, caps 0x58680001, chipst 0x9a6d pmurev 17, pmucaps 0x10a22b11 [ 50.979535] Thu Jan 1 00:00:50 1970:3 10.605341 Calibration data check pass. [ 50.983482] Thu Jan 1 00:00:50 1970:4 10.609293 Calibration data check pass. [ 50.983726] HTAVAIL is set, so not updating BBPLL Frequency [ 50.985854] wl1: wlc_attach: Overriding device id: 0x43a1 instead of 0x4360 [ 50.986069] Overriding device id = 0x43a1 [ 50.986204] wl1: wlc_bmac_phy_reset: band not yet set [ 50.986262] wlc_bmac_attach, deviceid 0x43a1 nbands 1 [ 50.986434] wl1: wlc_bmac_phy_reset: band not yet set [ 50.990772] wl1 phy_reg_write: No Clock Reg 173e Write is Not Allowed [ 50.990781] wl1 phy_reg_write: No Clock Reg 1739 Write is Not Allowed [ 50.990789] wl1 phy_reg_write: No Clock Reg 173a Write is Not Allowed [ 50.990796] wl1 phy_reg_write: No Clock Reg 1725 Write is Not Allowed [ 50.990803] wl1 phy_reg_write: No Clock Reg 1729 Write is Not Allowed [ 50.990811] wl1 phy_reg_write: No Clock Reg 1721 Write is Not Allowed [ 50.990818] wl1 phy_reg_write: No Clock Reg 1728 Write is Not Allowed [ 50.990826] wl1 phy_reg_write: No Clock Reg 1720 Write is Not Allowed [ 50.990833] wl1 phy_reg_mod: No Clock Reg 408 Write is Not Allowed [ 50.990840] wl1 phy_reg_write: No Clock Reg 417 Write is Not Allowed [ 50.990848] wl1 phy_reg_write: No Clock Reg 416 Write is Not Allowed [ 50.991961] wl1 phy_reg_mod: No Clock Reg 2e4 Write is Not Allowed [ 50.991968] wl1 phy_reg_write: No Clock Reg 1ec Write is Not Allowed [ 50.991981] wl1: wlc_bmac_attach: chiprev 3 corerev 42 cccap 0x58680001 maccap 0x30518c05 band 2.4G, phy_type 11 phy_rev 1 [ 50.992259] wl1 phy_reg_write: No Clock Reg 173e Write is Not Allowed [ 50.992267] wl1 phy_reg_write: No Clock Reg 1739 Write is Not Allowed [ 50.992275] wl1 phy_reg_write: No Clock Reg 173a Write is Not Allowed [ 50.992282] wl1 phy_reg_write: No Clock Reg 1725 Write is Not Allowed [ 50.992289] wl1 phy_reg_write: No Clock Reg 1729 Write is Not Allowed [ 50.992297] wl1 phy_reg_write: No Clock Reg 1721 Write is Not Allowed [ 50.992304] wl1 phy_reg_write: No Clock Reg 1728 Write is Not Allowed [ 50.992311] wl1 phy_reg_write: No Clock Reg 1720 Write is Not Allowed [ 50.992318] wl1 phy_reg_mod: No Clock Reg 408 Write is Not Allowed [ 50.992326] wl1 phy_reg_write: No Clock Reg 417 Write is Not Allowed [ 50.992333] wl1 phy_reg_write: No Clock Reg 416 Write is Not Allowed [ 50.992546] wl1: wlc_stf_txcore_shmem_write: No clock [ 50.992676] wl1: wlc_ampdu_tx_set: AGG Mode = MAC+AQM txmaxpkts 1024 [ 50.992685] wl1: wlc_ampdu_tx_set: 0x0, err 0 [ 50.993837] wl1: online cpus 2 [ 50.995277] wifi1: AP type AP-228, radio 1, max_bssids 16 [ 51.062521] wlc_phy_cal_init_acphy: NOT Implemented [ 51.090838] wl1: wlc_set_home_chanspec: Bad channel 1 [ 51.125623] wifi1: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.54_e1.2.2.4.10 (r425351 WLTEST) [ 51.125634] (Compiled in . at 00:36:28 on Oct 7 2017) [ 51.125639] [ 52.279935] bond0: no IPv6 routers present [ 55.151927] Kernel watchdog refresh ended. [ 55.744460] br0: no IPv6 routers present [ 107.405308] Thu Nov 23 20:37:58 2017:5 0.000000 wl0 set max_distance 0, radio type 0, outdoor_ap 0, [ 107.405328] Thu Nov 23 20:37:58 2017:6 0.000032 wl0 apply max distance 0(not mesh radio) [ 111.412028] Thu Nov 23 20:38:02 2017:7 4.006720 wifi0: Country Code set to DE [ 111.412056] Thu Nov 23 20:38:02 2017:8 4.006761 wifi0: VHT Mode Enabled [ 111.412122] Thu Nov 23 20:38:02 2017:9 4.006826 wifi0: Beacon Interval 100 [ 111.412137] Thu Nov 23 20:38:02 2017:10 4.006842 wifi0: HT Mode Enabled [ 111.412162] Thu Nov 23 20:38:02 2017:11 4.006865 wifi0: Effective External Antenna Gain set to 2.0 (connector loss 1.0) [ 111.474234] Thu Nov 23 20:38:02 2017:12 4.068927 wifi0: CDD Override is set to 0 [ 111.474253] Thu Nov 23 20:38:02 2017:13 4.068957 wifi0: txbf is enabled [ 111.474270] Thu Nov 23 20:38:02 2017:14 4.068974 wifi0: Energy Detect Threshold (EDT) set to -65dBm [ 111.475004] Thu Nov 23 20:38:02 2017:15 4.069705 wifi0: User EIRP:15.0 Actual EIRP:-32.0 Max EIRP:-32.0 Min EIRP:1.7 [ 112.415538] Thu Nov 23 20:38:03 2017:16 5.010228 wl1 set max_distance 0, radio type 0, outdoor_ap 0, [ 112.415558] Thu Nov 23 20:38:03 2017:17 5.010262 wl1 apply max distance 0(not mesh radio) [ 116.422183] Thu Nov 23 20:38:07 2017:18 9.016876 wifi1: Country Code set to DE [ 116.422202] Thu Nov 23 20:38:07 2017:19 9.016906 wifi1: Beacon Interval 100 [ 116.422227] Thu Nov 23 20:38:07 2017:20 9.016931 wifi1: HT Mode Enabled [ 116.422262] Thu Nov 23 20:38:07 2017:21 9.016965 (null): VHT Supported Rate set to 1023 [ 116.422296] Thu Nov 23 20:38:07 2017:22 9.016999 wifi1: Effective External Antenna Gain set to 2.5 (connector loss 0.5) [ 116.479280] Thu Nov 23 20:38:07 2017:23 9.073972 wifi1: 40MHz Intolerant set to 0 [ 116.479343] Thu Nov 23 20:38:07 2017:24 9.074047 wifi1: CDD Override is set to 0 [ 116.479358] Thu Nov 23 20:38:07 2017:25 9.074063 wifi1: txbf is enabled [ 116.479376] Thu Nov 23 20:38:07 2017:26 9.074079 wifi1: Energy Detect Threshold (EDT) set to -65dBm [ 116.480724] Thu Nov 23 20:38:07 2017:27 9.075421 wifi1: User EIRP:15.0 Actual EIRP:15.0 Max EIRP:17.7 Min EIRP:-2.5 [ 231.317952] Shutting down eth1 due to insufficient POE voltage [power profile 2] Driver Log -------------------------------------------------------- Current Log Level 3 Log Counter 28 Timestamp 42876.781226 1 10.199972 Calibration data check pass. 2 10.203930 Calibration data check pass. 3 10.605341 Calibration data check pass. 4 10.609293 Calibration data check pass. 5 0.000000 wl0 set max_distance 0, radio type 0, outdoor_ap 0, 6 0.000032 wl0 apply max distance 0(not mesh radio) 7 4.006720 wifi0: Country Code set to DE 8 4.006761 wifi0: VHT Mode Enabled 9 4.006826 wifi0: Beacon Interval 100 10 4.006842 wifi0: HT Mode Enabled 11 4.006865 wifi0: Effective External Antenna Gain set to 2.0 (connector loss 1.0) 12 4.068927 wifi0: CDD Override is set to 0 13 4.068957 wifi0: txbf is enabled 14 4.068974 wifi0: Energy Detect Threshold (EDT) set to -65dBm 15 4.069705 wifi0: User EIRP:15.0 Actual EIRP:-32.0 Max EIRP:-32.0 Min EIRP:1.7 16 5.010228 wl1 set max_distance 0, radio type 0, outdoor_ap 0, 17 5.010262 wl1 apply max distance 0(not mesh radio) 18 9.016876 wifi1: Country Code set to DE 19 9.016906 wifi1: Beacon Interval 100 20 9.016931 wifi1: HT Mode Enabled 21 9.016965 (null): VHT Supported Rate set to 1023 22 9.016999 wifi1: Effective External Antenna Gain set to 2.5 (connector loss 0.5) 23 9.073972 wifi1: 40MHz Intolerant set to 0 24 9.074047 wifi1: CDD Override is set to 0 25 9.074063 wifi1: txbf is enabled 26 9.074079 wifi1: Energy Detect Threshold (EDT) set to -65dBm 27 9.075421 wifi1: User EIRP:15.0 Actual EIRP:15.0 Max EIRP:17.7 Min EIRP:-2.5 (Aruba7210_Master_20) # ##### --------------------- sh lldp in re LocalPort | ChassisId PortId PortDescr SysName --------- + ------------------------- ------ --------- ---------------------- 40 | 40 e3 d6 c9 b7 8c 40 ... eth0 ArubaAP-011 config on the switch lldp enable-notification 40