------------------------------------------------------------------------------------------ Boot before conversion ------------------------------------------------------------------------------------------ APBoot 1.5.6.2 (build 61031) Built: 2017-08-16 at 21:03:03 Model: AP-37x DRAM: 491 MB SF: Detected MX25U3235F with page size 64 kB, total 4 MB Flash: 4 MB NAND: 132 MiB PCIE0: link up PCIE1: link up dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 168c 0040 00002 00 00000004 00000000 00000000 00000000 dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 168c 0046 00002 00 00000004 00000000 00000000 00000000 Power: 802.3af POE In: serial Out: serial Err: serial Net: eth0 Radio: qca9990#0, qca9983#1 Reset: warm FIPS: passed Hit to stop autoboot: 0 Checking image @ 0x0 Invalid image format version: 0xffffffff Checking image @ 0x2000000 Copying image from 0x44000000 Image is signed; verifying checksum... passed SHA2 Signature available Signer Cert OK Policy Cert OK RSA signature verified using SHA2. [ 0.000000] [ 0.000000] Aruba Networks [ 0.000000] ArubaOS Version 8.3.0.0-8.3.0.0 (build 61943 / label #61943) [ 0.000000] Built by p4build@rhodes on 2017-10-18 at 21:12:41 PDT (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine: IPQ806X wave-2 board [ 0.000000] Flash variant: default [ 0.000000] msm_reserve_memory: 0x44600000, 0x200000 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 123178 [ 0.075663] CPU1: Booted secondary processor [ 0.102655] clk_tbl_nss - loaded [ 0.228303] PCI: enabling device 0000:02:00.0 (0140 -> 0143) [ 0.228491] PCI: enabling device 0000:00:00.0 (0140 -> 0143) [ 0.256482] device tca9539 probe success [ 10.275226] m25p80 spi5.0: found mx25u3235f, expected s25fl512s [ 12.614932] Found AT97SC3203 on i2c-gpio0 [ 12.688441] no pmic restart interrupt specified [ 13.335145] [ 13.335176] Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT [ 13.414370] Starting Kernel HMAC-SHA1 KAT ...Starting Kernel DES KAT ...Completed Kernel DES KAT [ 13.520681] Starting Kernel AES KAT ...Completed Kernel AES KAT [ 13.564417] [ 13.610215] Completed Kernel HMAC-SHA1 KAT [ 13.660199] Starting Kernel AES¦Thu Jan 1 00:00:00 PST 1970 Completed Kernel AESGCM KAT Domain Name: SetMeUp.arubanetworks.com Current OEM Name : Aruba Networks Disabling ipv6 for devices by default AP-type has_ble_support: ONBOARD. IPv6 capability is supported for devices No panic info available Writing /dev/ttyHSL2 into /tmp/ble_port Enabling ble_daemon and ble_relay via nanny apfcutil: sector RAP: Cache uninitialized apfcutil: sector FAT: Cache uninitialized apfcutil: sector DRT: Cache uninitialized apfcutil: sector SCRATCH: Cache uninitialized Backup ENV. apfcutil: sector MESH Prov: Cache uninitialized [ 17.942986] nss_driver - fw of size 391744 bytes copied to load addr: 40000000, nss_id : 0 [ 18.052233] nss_driver - Turbo Support 1 [ 18.086722] Supported Frequencies - 110Mhz 550Mhz 733Mhz [ 18.156888] nss_driver - fw of size 190016 bytes copied to load addr: 40800000, nss_id : 1 [ 18.290909] nss_crypto_module_init[273]:module loaded (platform - IPQ806x, build - Oct 18 2017:21:01:57) Enter non-FIPS mode Cfg len is 0 Configuration file is empty, turning on default services... extended ssid activate due to no AP config ... The AP is in factory default status Ethernet port 1 mode: active-standby[ 19.414964] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 19.516557] bonding: MII link monitoring set to 400 ms [ 19.590284] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 19.646641] ADDRCONF(NETDEV_UP): bond0: link is not ready [ 19.715432] bonding: bond0: enslaving eth0 as a backup interface with a down link. Info: use bonding and enslave eth1[ 19.809590] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 19.907810] bonding: bond0: enslaving eth1 as a backup interface with a down link. Starting watchdog process... touching file /tmp/ip_mode_0 Aruba watchdog daemon started [2[ 20.050984] Kernel watchdog refresh ended on core 0. thread(s)] init usb modem ... USB is not supported on this model [ 20.222805] Kernel watchdog refresh ended on core 1. Ethernet uplink not active yet [ 21.986691] nss_crypto_process_event[388]:engine(0) opened successfully [ 22.053420] nss_crypto_process_event[388]:engine(1) opened successfully [ 22.132583] nss_crypto_process_event[388]:engine(2) opened successfully [ 22.211746] nss_crypto_process_event[388]:engine(3) opened successfully Ethernet uplink not active yet [ 22.961761] eth0: 1000 Mbps Full Duplex [ 23.090784] bonding: bond0: link status definitely up for interface eth0, 1000 Mbps full duplex. [ 23.183880] bonding: bond0: making interface eth0 the new active one. [ 23.261012] bonding: bond0: first active interface up! [ 23.322274] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready [ 24.009215] Settng Jumbo MRU 2000 Ethernet uplink active. Becoming Mesh Portal Mesh is DISABLED on this device. extended ssid is activated on [ 24.125804] drvlog_mod: module license 'Proprietary' taints kernel. [ 24.267353] Disabling lock debugging due to kernel taint the platform ... copying bootuplog ... [ 24.355607] AP xml model 109, num_radios 2 (jiffies 12174) [ 24.440268] apType 109 hw_opmode 0 [ 24.481255] radio 0: band 1 ant 0 max_ssid 16 [ 24.532989] radio 1: band 0 ant 0 max_ssid 16 [ 24.585379] init_asap_mod: installation:0 [ 24.632989] election init: rand=a HZ=500 [ 24.680099] IAP client match init [ 24.719681] ethernet_device_event: dev eth0 is up [ 24.775913] ethernet_device_event: dev eth1 is up allow PAPI set device anul0 mtu to 2000 notify asap_mod 3g no present... Starting update SBL2 ... SBL2 was updated already CMDLINE_WRITE_ENVIRONMENT arg {NEW_SBL2=1} Done. apdot1x authentication is not enabled LLDP not sent yet, DHCP is waiting LLDP not sent yet, DHCP is waiting LLDP not sent yet, DHCP is waiting LLDP not sent yet, DHCP is waiting Starting DHCP Getting an IP address... Jan 1 00:00:16 udhcpc[3121]: udhcpc (v0.9.9-pre) started Jan 1 00:00:16 udhcpc[3121]: send_discover: pkt num 0, secs 0 Jan 1 00:00:16 udhcpc[3121]: Sending discover... Jan 1 00:00:17 udhcpc[3121]: send_selecting: pkt num 0, secs 512 Jan 1 00:00:17 udhcpc[3121]: Sending select for 10.11.48.20... Jan 1 00:00:17 udhcpc[3121]: Lease of 10.11.48.20 obtained, lease time 691200 Jan 1 00:00:17 udhcpc[3121]: DHCP OPT 60 is ArubaAP [ 31.690784] ip_time_handler: Got ip and packets on bond0 Started master election 7-0, rand 26 10.11.48.20 255.255.255.0 10.11.48.254 ADP is disabled by uap_controller_less Compressing all files in the /etc/httpd directory... Done. Starting Webserver bind: Transport endpoint is not connected bind: Transport endpoint is not connected bind: Transport endpoint is not connected Launching NTP Client on pool.ntp.org Error resolving pool.ntp.org: Name or service not known (-2) 1 Jan 08:01:10 nt[ 84.733645] ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D) pdate[3416]: Can't find host pool.ntp.org: Name or service not k[ 84.832271] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved nown (-2) 1 Jan 08:01:10 ntpdate[3416]: no servers can be used[ 85.010871] ath_dfs: Version 2.0.0 [ 85.010871] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved , exiting [ 85.215557] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 85.340018] ath_pci: (Atheros/multi-bss) [ 85.375695] PCI: enabling device 0000:01:00.0 (0140 -> 0142) [ 85.443830] ath_pci 0000:01:00.0: ath DEBUG: sc=0xd87d1800 [ 86.739987] HTC Rx: insufficient length, got:4 expected =8 [ 86.793220] Startup Mode-0 set [ 86.830240] htt_peer_map_timer_init Enter pdev d5f04000 hrtimer d5f069b0 [ 86.909809] [ 86.909809] htt_alloc_peer_map_mem : Alloc Success : host q vaddr d4d02000 paddr 56202000 [ 87.026897] [ 87.026897] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 87.129365] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d88c0000 [ 87.223555] [ 87.223586] SERIAL NUMBER: : wifi1 [ 87.223586] [ 87.299406] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 87.453045] wmi_ready_event_rx: WMI UNIFIED READY event [ 87.505467] target uses HTT version 2.2; host uses 2.2 [ 87.511808] ol_ath_smart_ant_attach: Firmware doest not support Smart Antenna. [ 87.511808] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. [ 87.511840] dfs_attach: event log disabled by default [ 87.513589] aruba_mods_radio_attach: dev: ic:d4d80540 osdev:d87d1810 phy:2 [ 87.513620] wifi1: Base BSSID 80:8d:b7:75:87:c0, 16 available BSSID(s) processor ID: 0 [ 87.513620] eth0 address=80:8d:b7:cf:58:7c [ 87.513620] br0 address=80:8d:b7:cf:58:7c [ 87.513620] wifi1: AP type AP-375, radio 1, max_bssids 16 [ 87.513620] aruba_mods_radio_attach() INT setting antenna polarization to 1 radio 1 [ 87.513651] Resetting spectral chainmask to Rx chainmask [ 87.619993] Enabling eth1 due to power change [power profile 1] [ 87.620556] Resetting spectral chainmask to Rx chainmask [ 87.620743] Init the PCAP for radio1 offload 1. [ 87.621055] aruba_mods_radio_attach: radio: 1, init txq work cpu: core-1 [ 87.621118] PCI: enabling device 0000:03:00.0 (0140 -> 0142) [ 87.621430] ath_pci 0000:03:00.0: ath DEBUG: sc=0xd4758800 [ 93.345923] HTC Rx: insufficient length, got:4 expected =8 [ 93.399250] Startup Mode-0 set [ 93.436019] htt_peer_map_timer_init Enter pdev d475c000 hrtimer d475e9b0 [ 93.515776] [ 93.515776] htt_alloc_peer_map_mem : Alloc Success : host q vaddr dbce4000 paddr 5d1e4000 [ 93.632833] [ 93.632864] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 93.735676] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d4340000 [ 93.829428] [ 93.829428] SERIAL NUMBER: : wifi0 [ 93.829428] [ 93.905342] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 94.063136] wmi_ready_event_rx: WMI UNIFIED READY event [ 94.115713] target uses HTT version 2.2; host uses 2.2 [ 94.219462] dfs_attach: event log disabled by default [ 94.270415] aruba_mods_radio_attach: dev: ic:d4800540 osdev:d4758810 phy:2 [ 94.357388] wifi0: Base BSSID 80:8d:b7:75:87:d0, 16 available BSSID(s) processor ID: 0 [ 94.451827] eth0 address=80:8d:b7:cf:58:7c [ 94.501155] br0 address=80:8d:b7:cf:58:7c [ 94.548672] wifi0: AP type AP-375, radio 0, max_bssids 16 [ 94.613683] aruba_mods_radio_attach() INT setting antenna polarization to 1 radio 0 [ 94.706216] Resetting spectral chainmask to Rx chainmask [ 94.769540] Resetting spectral chainmask to Rx chainmask [ 94.833895] Init the PCAP for radio0 offload 1. [ 94.887628] aruba_mods_radio_attach: radio: 0, init txq work cpu: core-0 [ 94.972664] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 [ 95.053951] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 AP rebooted Wed Dec 31 16:03:03 PST 1969; SAPD: UAP controller less shutting down watchdog process (nanny will restart it)... <<<<< Welcome to the Access Point >>>>> Completed SW FIPS KAT test User: [ 98.938800] Starting Kernel HMAC SHA1 FIPS KAT ... [ 98.981911] Completed Kernel HMAC SHA1 FIPS KAT [ 99.364792] Kernel watchdog refresh ended on core 1. [ 99.412808] Kernel watchdog refresh ended on core 0. [ 100.943580] Starting Kernel HMAC SHA256 FIPS KAT ... [ 100.988972] Completed Kernel HMAC SHA256 FIPS KAT [ 102.950796] Starting Kernel HMAC SHA384 FIPS KAT ... [ 102.999187] Completed Kernel HMAC SHA384 FIPS KAT [ 104.950796] Starting Kernel HMAC SHA512 FIPS KAT ... [ 104.999218] Completed Kernel HMAC SHA512 FIPS KAT [ 116.202155] aruba_commit_radio 1459 d4d80540 [ 116.206591] aruba_commit_radio 1459 d4800540 [ 116.218744] aruba_commit_radio 1459 d4800540 [ 116.343830] aruba_commit_radio 1459 d4d80540 [ 117.795501] bonding: bond0: releasing backup interface eth1 [ 117.850452] ethernet_device_event: dev eth1 others: 9 [ 117.910153] i am master now [ 117.943486] (08:01:44) !!! Init ---> Master [ 117.993470] asap_send_elected_master: sent successfully [ 118.057669] ethernet_device_event: dev eth1 is down [ 118.115463] ethernet_device_event: dev eth1 others: 8 [ 118.178412] ethernet_device_event: dev eth1 others: 13 [ 118.236988] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 118.299812] ethernet_device_event: dev eth1 is up User: admin System uptime is 136 seconds and CLI is not ready yet, please try again later. User: admin [ 157.940768] [sched_delayed] sched: RT throttling activated Password: Warning: CLI is currently running in upgrade-only mode. Only upgrade operation is supported, other operations may not funcion. 80:8d:b7:cf:58:7c# con configure Configuration commands connect-support convert-aos-ap 80:8d:b7:cf:58:7c# convert-aos-ap CAP 10.11.48.253 The system is going down NOW !! Sending SIGKILL to all processes. [ 217.851796] UBIFS: un-mount UBI device 2, volume 0 Unmounting UBIFS completed. Please stand by while rebooting the system. [ 219.999656] Restarting system. [ 220.023680] Going down for restart now ------------------------------------------------------------------------------------------ Boot after conversion ------------------------------------------------------------------------------------------ APBoot 1.5.6.2 (build 61031) Built: 2017-08-16 at 21:03:03 Model: AP-37x DRAM: 491 MB SF: Detected MX25U3235F with page size 64 kB, total 4 MB Flash: 4 MB NAND: 132 MiB PCIE0: link up PCIE1: link up dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 168c 0040 00002 00 00000004 00000000 00000000 00000000 dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 168c 0046 00002 00 00000004 00000000 00000000 00000000 Power: 802.3af POE In: serial Out: serial Err: serial Net: eth0 Radio: qca9990#0, qca9983#1 Reset: warm FIPS: passed Hit to stop autoboot: 0 Booting OS partition 0 Checking image @ 0x0 Copying image from 0x44000000 Image is signed; verifying checksum... passed SHA2 Signature available Signer Cert OK Policy Cert OK RSA signature verified using SHA2. [ 0.000000] [ 0.000000] Aruba Networks [ 0.000000] ArubaOS Version 8.3.0.0 (build 64659 / label #64659) [ 0.000000] Built by p4build@pr-hpn-build09 on 2018-04-27 at 22:28:24 UTC (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine: IPQ806X wave-2 board [ 0.000000] Flash variant: default [ 0.000000] msm_reserve_memory: 0x44600000, 0x200000 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 123178 [ 0.075757] CPU1: Booted secondary processor [ 0.102780] clk_tbl_nss - loaded [ 0.228678] PCI: enabling device 0000:02:00.0 (0140 -> 0143) [ 0.228865] PCI: enabling device 0000:00:00.0 (0140 -> 0143) [ 0.256294] device tca9539 probe success [ 5.703061] m25p80 spi5.0: found mx25u3235f, expected s25fl512s [ 8.220649] Found AT97SC3203 on i2c-gpio0 [ 8.294345] no pmic restart interrupt specified [ 8.938081] [ 8.938081] Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT [ 9.017307] Starting Kernel HMAC-SHA1 KAT ...Starting Kernel DES KAT ...Completed Kernel DES KAT [ 9.123586] Starting Kernel AES KAT ...Completed Kernel AES KAT [ 9.167385] [ 9.213214] Completed Kernel HMAC-SHA1 KAT [ 9.263167] Starting Kernel AESGCM KAT ...Completed Kernel AESGCM KAT Populate AP type info AP-type has_ble_support: ONBOARD. Domain Name: arubanetworks.com No panic info available Writing /dev/ttyHSL2 into /tmp/ble_port Enabling ble_daemon via nanny [ 13.356701] nss_driver - fw of size 391744 bytes copied to load addr: 40000000, nss_id : 0 [ 13.465916] nss_driver - Turbo Support 1 [ 13.500406] Supported Frequencies - 110Mhz 550Mhz 733Mhz [ 13.570509] nss_driver - fw of size 190016 bytes copied to load addr: 40800000, nss_id : 1 Ethernet port 1 mode: active-standby [ 34.869009] drvlog_mod: module license 'Proprietary' taints kernel. [ 34.931583] Disabling lock debugging due to kernel taint [ 35.024179] init_asap_mod: installation:0 [ 35.059700] ethernet_device_event: dev eth0 is up [ 35.127116] firewall cpu: core-1 [ 35.749640] ethernet_device_event: dev eth0 is changed, carrier: 0 [ 36.294439] ethernet_device_event: dev eth0 is changed, carrier: 1 [ 37.368759] Settng Jumbo MRU 2000 set device anul0 mtu to 2000 Starting watchdog process... Aruba watchdog daemon started [2 thread(s)] Starting update SBL2 ... SBL2 was updated already Done. LLDP not sent yet, DHCP is waiting Starting DHCP net.ipv4.conf.all.arp_notify = 1 Getting an IP address... net.ipv4.conf.all.arp_notify = 0 net.ipv4.conf.br0.arp_notify = 1 10.11.48.20 255.255.255.0 10.11.48.254 Running ADP...Done. Master is 10.11.48.253 [ 47.333926] PCI: enabling device 0000:01:00.0 (0140 -> 0142) [ 48.587566] Startup Mode-0 set [ 48.611902] htt_peer_map_timer_init Enter pdev dc870000 hrtimer dc8729b0 [ 48.691815] [ 48.691815] htt_alloc_peer_map_mem : Alloc Success : host q vaddr dd3b8000 paddr 5e8b8000 [ 48.808434] [ 48.808466] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 48.911965] [ 48.911965] SERIAL NUMBER: : wifi1 [ 48.911965] [ 49.058544] wmi_ready_event_rx: WMI UNIFIED READY event [ 49.117369] ol_ath_smart_ant_attach: Firmware doest not support Smart Antenna. [ 49.197125] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. [ 49.283630] dfs_attach: event log enabled by default [ 49.342955] dfs_attach: default dfs_debug_mask:0x900 [ 49.402592] dfs_init_radar_filters: dfsdomain=0, numradars=0, numb5radars=0 [ 49.485660] dfs_init_radar_filters: Unknown dfs domain 0 [ 49.550671] wifi1: Base BSSID 80:8d:b7:75:87:c0, 16 available BSSID(s) processor ID: 0 [ 49.644048] eth0 address=80:8d:b7:cf:58:7c [ 49.692970] br0 address=80:8d:b7:cf:58:7c [ 49.740893] wifi1: AP type AP-375, radio 1, max_bssids 16 [ 49.805467] aruba_mods_radio_attach() INT setting antenna polarization to 1 radio 1 [ 49.898219] Resetting spectral chainmask to Rx chainmask [ 50.065198] Init the PCAP for radio1 offload 1. [ 50.107185] aruba_mods_radio_attach: radio: 1, init txq work cpu: core-1 [ 50.187191] PCI: enabling device 0000:03:00.0 (0140 -> 0142) [ 55.952733] Startup Mode-0 set [ 55.977132] htt_peer_map_timer_init Enter pdev d7b48000 hrtimer d7b4a9b0 [ 56.056950] [ 56.056950] htt_alloc_peer_map_mem : Alloc Success : host q vaddr dd3be000 paddr 5e8be000 [ 56.173664] [ 56.173664] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 56.277100] [ 56.277100] SERIAL NUMBER: : wifi0 [ 56.277100] [ 56.426429] wmi_ready_event_rx: WMI UNIFIED READY event [ 56.520899] dfs_attach: event log enabled by default [ 56.567822] dfs_attach: default dfs_debug_mask:0x900 [ 56.627428] dfs_init_radar_filters: dfsdomain=0, numradars=0, numb5radars=0 [ 56.710527] dfs_init_radar_filters: Unknown dfs domain 0 [ 56.776601] wifi0: Base BSSID 80:8d:b7:75:87:d0, 16 available BSSID(s) processor ID: 0 [ 56.868884] eth0 address=80:8d:b7:cf:58:7c [ 56.917838] br0 address=80:8d:b7:cf:58:7c [ 56.965760] wifi0: AP type AP-375, radio 0, max_bssids 16 [ 57.030365] aruba_mods_radio_attach() INT setting antenna polarization to 1 radio 0 [ 57.123117] Resetting spectral chainmask to Rx chainmask [ 57.187191] Init the PCAP for radio0 offload 1. [ 57.241080] aruba_mods_radio_attach: radio: 0, init txq work cpu: core-0 [ 57.337675] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 [ 57.412621] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 AP rebooted Thu Jan 1 08:16:13 UTC 1970; System cmd at uptime 0D 0H 16M 26S: Image Upgrade Successful shutting down watchdog process (nanny will restart it)... <<<<< Welcome to the Access Point >>>>> ~ # The system is going down NOW !! Sending SIGTERM to all processes. Unmounting UBIFS completed.esses. Please stand by while rebooting the system. [ 192.389753] Restarting system.