CPBoot 1.0.0.0 (build 23274) Built: 2010-01-19 at 11:11:22 DDR2 DRAM running at 466Mhz DRAM: Total = 512 MB POST: Memory test: Physical 0 - 0x10000000 - quick test Memory test: Physical 0x10000000 - 0x20000000 - quick test PASS CPU: XLS408, rev. B1 Clock: 600MHz CPLD: rev: 1.3 SMP: All 8 cpus successfully started Board: A650 POST2: OK PCIE: RC2x2 mode Net: xls_gmac0, xls_gmac1 [PRIME], xls_gmac2, xls_gmac3, xls_gmac4, xls_gmac5 NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca ( NAND 256MiB 3,3V 16-bit) Boot: Primary bootflash partition Hit any key to stop autoboot: 0 cpboot> cpboot> cpboot> cpboot> cpboot> cpboot> cpboot> cpboot> setenv cfgfile default1.cfg cpboot> saveenv Saving Environment to Flash... Erasing # Erased 1 sectors Writing ######## cpboot> printenv bootargs=quiet bootcmd=bootf bootdelay=5 baudrate=9600 loadaddr=0x87000000 bootfile=vmlinux.strip psb_os_cpu_mask=0 userapp_cpu_map=0x0f eth6addr=00:0b:86:99:47:42 eth7addr=00:0b:86:99:46:42 ethprime=xls_gmac1 boardname=grenache partition=nand0,0 wipe-out-flash=nand erase 0x6400000 0x9c00000 ethaddr=00:0b:86:65:e6:d0 eth1addr=00:0b:86:65:e6:d1 eth2addr=00:0b:86:65:e6:d2 eth3addr=00:0b:86:65:e6:d3 eth4addr=00:0b:86:65:e6:d4 eth5addr=00:0b:86:65:e6:d5 stdin=serial stdout=serial stderr=serial ethact=xls_gmac1 mtdparts=mtdparts=image0:52428800@0(sys0) mtdids=nand0=image0 cfgfile=default1.cfg Environment size: 595/65532 bytes cpboot> reset ----------------------------------------------------------------- System will be rebooted in about 1 seconds.. CPBoot 1.0.0.0 (build 23274) Built: 2010-01-19 at 11:11:22 DDR2 DRAM running at 466Mhz DRAM: Total = 512 MB POST: Memory test: Physical 0 - 0x10000000 - quick test Memory test: Physical 0x10000000 - 0x20000000 - quick test PASS CPU: XLS408, rev. B1 Clock: 600MHz CPLD: rev: 1.3 SMP: All 8 cpus successfully started Board: A650 POST2: OK PCIE: RC2x2 mode Net: xls_gmac0, xls_gmac1 [PRIME], xls_gmac2, xls_gmac3, xls_gmac4, xls_gmac5 NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca ( NAND 256MiB 3,3V 16-bit) Boot: Primary bootflash partition Hit any key to stop autoboot: 0 booting system partition 1 part offset: 3200000 part size: 3200000 ### JFFS2 loading 'uImage' to 0x87000000 Scanning JFFS2 FS: load: loaded 'uImage' to 0x87000000 (26619864 bytes) ### JFFS2 load complete: 26619864 bytes loaded to 0x87000000 Booting image... Image is signed; verifying checksum... passed Signer Cert OK Policy Cert OK RSA signature verified. Jumping to the application... 0x8065c000 Linux command line: run quiet console=ttyS0,9600 ------------------------------------------------------------ Downloading SOS...done. Uncompressing core image files...done. Mounting the flash file systems...done. Aruba Networks ArubaOS Version 6.1.2.3-FIPS (build 31979 / label #31979) Built by p4build@cartman on 2012-01-18 at 17:14:52 PST (gcc version 3.4.3) Copyright (c) 2002-2012, Aruba Networks, Inc. <<<<< Welcome to Aruba Networks - Aruba A650-US >>>>> Starting watchdog processes Check/update Boot Image Reboot Cause: Power Failure. SKIPPING Generating SSH Keys......0022 done. Initializing TPM and Certificates Performing integrity check on Ancillary partition 1...passed. Restoring the database...done. Starting hwMon Reading configuration from factory-default.cfg ***************** Welcome to the Aruba650 setup dialog ***************** This dialog will help you to set the basic configuration for the switch. These settings, except for the Country Code, can later be changed from the Command Line Interface or Graphical User Interface. Commands: Submit input or use [default value], Help Back, Forward, Line begin, Line end Delete, Delete back, Delete to end of line Previous question Restart beginning Enter System name [Aruba650]: Starting FIPS Aruba Cryptographic KAT test Enter Switch Role (master|local|standalone|remote-node) [master]: Completed FIPS Aruba Cryptographic KAT test successfully. Starting FIPS OpenSSL KAT test Enter System name [Aruba650]: EAGN-U02-WC-03 Enter Switch Role (master|local|standalone|remote-node) [master]: Enter VLAN 1 interface IP address [172.16.0.254]: 192.168.1.1 Enter VLAN 1 interface subnet mask [255.255.255.0]: Enter IP Default gateway [none]: Completed FIPS OpenSSL KAT test successfully. 192.168.1.2 This controller is restricted to Country code US for United States, please confirm (yes|no)?: yes Enter Time Zone [PST-8:0]: EST-5:0 Enter Time in UTC [07:23:20]: 11:25:00 Enter Date (MM/DD/YYYY) [5/19/2012]: 5/18/2012 Enter Password for admin login (up to 32 chars): ********* Re-type Password for admin login: ********* Enter Password for enable mode (up to 15 chars): ****** Re-type Password for enable mode: ****** Do you wish to shutdown all the ports (yes|no)? [no]: Current choices are: System name: EAGN-U02-WC-03 Switch Role: master VLAN 1 interface IP address: 192.168.1.1 VLAN 1 interface subnet mask: 255.255.255.0 IP Default gateway: 192.168.1.2 Time Zone: EST-5:0 Ports shutdown: no If you accept the changes the switch will restart! Type to go back and change answer for any question Do you wish to accept the changes (yes|no)yes Creating configuration... Done. System will now restart! Shutdown processing started Syncing data....done. Sending SIGKILL to all processes. Please stand by while rebooting the system. 1:<0>Restarting system. 1:. 1:<2>Performing hard reset... CPBoot 1.0.0.0 (build 23274) Built: 2010-01-19 at 11:11:22 DDR2 DRAM running at 466Mhz DRAM: Total = 512 MB POST: Memory test: Physical 0 - 0x10000000 - quick test Memory test: Physical 0x10000000 - 0x20000000 - quick test PASS CPU: XLS408, rev. B1 Clock: 600MHz CPLD: rev: 1.3 SMP: All 8 cpus successfully started Board: A650 POST2: OK PCIE: RC2x2 mode Net: xls_gmac0, xls_gmac1 [PRIME], xls_gmac2, xls_gmac3, xls_gmac4, xls_gmac5 NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca ( NAND 256MiB 3,3V 16-bit) Boot: Primary bootflash partition Hit any key to stop autoboot: 0 cpboot> cpboot> cpboot> cpboot> cpboot> cpboot> cpboot> cpboot> cpboot> cpboot> cpboot> cpboot> setenv cfgfile cpboot> savenv Unknown command 'savenv' - try 'help' cpboot> saveenv Saving Environment to Flash... Erasing # Erased 1 sectors Writing ######## cpboot> boot booting system partition 1 part offset: 3200000 part size: 3200000 ### JFFS2 loading 'uImage' to 0x87000000 Scanning JFFS2 FS: load: loaded 'uImage' to 0x87000000 (26619864 bytes) ### JFFS2 load complete: 26619864 bytes loaded to 0x87000000 Booting image... Image is signed; verifying checksum... passed Signer Cert OK Policy Cert OK RSA signature verified. Jumping to the application... 0x8065c000 Linux command line: run quiet console=ttyS0,9600 ------------------------------------------------------------ Downloading SOS...done. Uncompressing core image files...done. Mounting the flash file systems...done. Aruba Networks ArubaOS Version 6.1.2.3-FIPS (build 31979 / label #31979) Built by p4build@cartman on 2012-01-18 at 17:14:52 PST (gcc version 3.4.3) Copyright (c) 2002-2012, Aruba Networks, Inc. <<<<< Welcome to Aruba Networks - Aruba A650-US >>>>> Starting watchdog processes Check/update Boot Image Reboot Cause: User reboot. SKIPPING Generating SSH Keys......0022 done. Initializing TPM and Certificates Performing integrity check on Ancillary partition 1...passed. Restoring the database...done. Starting hwMon Reading configuration from default.cfg Starting FIPS Aruba Cryptographic KAT test Completed FIPS Aruba Cryptographic KAT test successfully. Starting FIPS OpenSSL KAT test Retrieving Configuration...will take approximately 1 minute Completed FIPS OpenSSL KAT test successfully. (EAGN-U02-WC-03) User: admin Password: ********* (EAGN-U02-WC-03) >en Password:****** Password:****** (EAGN-U02-WC-03) # (EAGN-U02-WC-03) #write m Saving Configuration... Configuration Saved. (EAGN-U02-WC-03) #