APBoot 1.2.7.4 (build 32721) Built: 2012-03-08 at 11:37:20 Model: RAP-3x CPU: AR9344 revision: 1.2 Clock: 560 MHz, DDR rate: 450 MHz, Bus clock: 225 MHz DRAM: 128 MB POST1: passed Copy: done Flash: 16 MB Net: eth0 Radio: ar9344#0 Hit to stop autoboot: 0 Booting OS partition 0 Checking image @ 0xbf100000 Image is signed; verifying checksum... passed Signer Cert OK Policy Cert OK RSA signature verified. ELF file is 32 bit Loading .text @ 0x80e00000 (5650104 bytes) Loading .data @ 0x813636c0 (32 bytes) Clearing .bss @ 0x813636e0 (16 bytes) ## Starting application at 0x80e00000 ... Uncompressing..................................................... Alcatel-Lucent AOS-W Version 6.2.1.3 (build 39155 / label #39155) Built by p4build@stan on 2013-07-24 at 11:01:31 PDT (gcc version 4.3.3) CPU Rev: 2122 934x CPU flash_size passed from bootloader = 16 arg 1: mem=128M Flash variant: 16M ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225 Cache parity protection disabled ath_timer_init: plat time init done Using 280.000 MHz high precision timer. cycles_per_jiffy=560000 Memory: 120960k/131072k available (1920k kernel code, 10040k reserved, 756k data, 4744k init, 0k highmem) available. detected lzma initramfs initramfs: LZMA lc=3,lp=0,pb=2,dictSize=8388608,origSize=21280768 LZMA initramfs by Ming-Ching Tiew ................................................................................................................... ........................................................................................................................................................................ .......................................... ATH GPIOC major 0 wdt: registered with refresh Enabling Watchdog Talisker RSSI LED initialization Creating 1 MTD partitions on "ath-nor0": 0x00000000-0x01000000 : "flash" i2c /dev entries driver i2c-talisker: using default base 0x18040000 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT Starting Kernel DES KAT ...Completed Kernel DES KAT Starting Kernel AES KAT ...Completed Kernel AES KAT Domain Name: alcatel-lucent.com No panic info available ATHR_GMAC: RX TASKLET - Pkts per Intr:16 ATHR_GMAC: Mac address for unit 0:80870bc0 ATHR_GMAC: 00:0b:86:8e:c8:23 mac:0 Registering S27.... ATHR_GMAC: Mac capability flags : 2400 ATHR_GMAC: RX TASKLET - Pkts per Intr:16 ATHR_GMAC: Mac address for unit 1:80870bc0 ATHR_GMAC: 00:0b:86:8e:c8:24 mac:1 Registering S27.... ATHR_GMAC: Mac capability flags : 2C00 asap_switch: module license 'Proprietary' taints kernel. Setting PHY... ADDRCONF(NETDEV_UP): ethsw: link is not ready Ethernet port 1 mode: tunnel Ethernet Channel Bonding Driver: v3.0.1 (January 9, 2006) Setting PHY... enet1 port3 up ATHR_GMAC: Enet Unit:1 PHY:3 is UP RGMii 100Mbps full duplex ATHR_GMAC: Enet Unit:0 PHY:4 is UP Mii 100Mbps full duplex ADDRCONF(NETDEV_CHANGE): ethsw: link becomes ready Setting PHY... ATHR_GMAC: Enet Unit:0 PHY:4 is UP Mii 100Mbps full duplex bonding: bond0: making interface eth0 the new active one. bonding: bond0: enslaving eth0 as an active interface with an up link. ADDRCONF(NETDEV_UP): eth1: link is not ready AP xml model 57, num_radios 1 (jiffies 10376) init_asap_mod: installation:0 radio 0: band 0 ant 0 max_ssid 16 ethernet_device_event: dev eth0 is register ethernet_device_event: dev eth0 is up setting bond0 as bridge child setting gre0 as split child USB not provisioned ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready Starting watchdog process... Getting an IP address... 192.168.1.20 255.255.255.0 192.168.1.1 Running ADP...Done. Master is ***********(Top Secret) Starting Webserver bind: Transport endpoint is not connected ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, PRIVATE_DIAG, WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_rate_atheros: Aruba Networks Rate Control Algorithm ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_spectrum: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_pci: 0.9.4.5 (Atheros/multi-bss) ath_ahb: 0.9.4.5 (Atheros/multi-bss) ath_ahb: init_ath_wmac Restoring Cal data from Flash Reading from Addr: 0xbffe1000 wifi0: Base BSSID 6c:f3:7f:75:5c:70, 16 available BSSID(s) eth0 address=00:0b:86:8e:c8:23 br0 address=00:0b:86:8e:c8:23 wifi0: AP type RAP-3WNP, radio 0, max_bssids 16 wifi0: Atheros 9340: mem=0xb8100000, irq=2 Starting FIPS KAT ... Completed FIPS KAT AP rebooted Fri Dec 31 16:06:34 PST 1999; RENEWING state; t1 150 t2 262 lease 300 (saved_ip 100.64.98.14 yiaddr 192.168.1.20 saved_router 100.127.255.0 new_router 192.1 68.1.1) shutting down watchdog process (nanny will restart it)... <<<<< Welcome to the Access Point >>>>> ~ # enet1 port3 down ATHR_GMAC:unit 1: phy 3 not up carrier 1 ADDRCONF(NETDEV_UP): eth1: link is not ready ADDRCONF(NETDEV_UP): eth2: link is not ready enet1 port3 up ATHR_GMAC: Enet Unit:1 PHY:3 is UP RGMii 100Mbps full duplex ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready enet1 port3 down ATHR_GMAC:unit 1: phy 3 not up carrier 1 ADDRCONF(NETDEV_UP): eth1: link is not ready enet1 port3 up ATHR_GMAC: Enet Unit:1 PHY:3 is UP RGMii 100Mbps full duplex ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready