-- ArubaOS 6.4.2.8_50314 -- vim:set ts=4 sw=4: WLSX-WLAN-MIB DEFINITIONS ::= BEGIN IMPORTS TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-IDENTITY, OBJECT-TYPE, snmpModules, Integer32, Unsigned32, Counter32, IpAddress, NOTIFICATION-TYPE FROM SNMPv2-SMI TDomain, DisplayString, PhysAddress, TAddress, TimeInterval, RowStatus, StorageType, TestAndIncr, MacAddress, TruthValue FROM SNMPv2-TC ifIndex FROM RFC1213-MIB ArubaEnableValue, ArubaFrameType, ArubaActiveState, ArubaRogueApType, ArubaAuthenticationMethods, ArubaEncryptionMethods, ArubaPhyType, ArubaVoipProtocolType, ArubaVlanValidRange, ArubaAccessPointMode, ArubaAPStatus, ArubaEnet1Mode, ArubaUnprovisionedStatus, ArubaMonitorMode, ArubaAntennaSetting, ArubaMeshRole, ArubaHTMode, ArubaHTExtChannel FROM ARUBA-TC OBJECT-GROUP FROM SNMPv2-CONF wlsxEnterpriseMibModules FROM ARUBA-MIB; wlsxWlanMIB MODULE-IDENTITY LAST-UPDATED "1001261806Z" ORGANIZATION "Aruba Wireless Networks" CONTACT-INFO "Postal: 1322 Crossman Avenue Sunnyvale, CA 94089 E-mail: dl-support@arubanetworks.com Phone: +1 408 227 4500" DESCRIPTION "This MIB module defines MIB objects which provide information about the Wireless Management System (WMS) in the Aruba Controller." REVISION "1001261806Z" DESCRIPTION "The initial revision." ::= { wlsxEnterpriseMibModules 5 } wlsxWlanConfigGroup OBJECT IDENTIFIER ::= { wlsxWlanMIB 1 } wlsxWlanStateGroup OBJECT IDENTIFIER ::= { wlsxWlanMIB 2 } wlsxWlanStatsGroup OBJECT IDENTIFIER ::= { wlsxWlanMIB 3 } wlsxRAPTraps OBJECT IDENTIFIER ::= { wlsxWlanMIB 100 } -- wlsxWlanAccessPointInfoGroup contains a Local Access Point Information Table. -- which lists all the APs connected to the controller, a Global AP Info Table -- which lists all the APs in the Aruba Domain. The Global table is valid only -- on the Master controller. The Group also contains two scalar objects which -- indicate the total number of APs and the total number of Clients connected. wlsxWlanAccessPointInfoGroup OBJECT IDENTIFIER ::= { wlsxWlanStateGroup 1 } wlsxWlanStationInfoGroup OBJECT IDENTIFIER ::= { wlsxWlanStateGroup 2 } wlsxWlanAssociationInfoGroup OBJECT IDENTIFIER ::= { wlsxWlanStateGroup 3 } wlsxWlanAccessPointStatsGroup OBJECT IDENTIFIER ::= { wlsxWlanStatsGroup 1 } wlsxWlanStationStatsGroup OBJECT IDENTIFIER ::= { wlsxWlanStatsGroup 2 } wlsxWlanSwitchStatsGroup OBJECT IDENTIFIER ::= { wlsxWlanStatsGroup 3 } wlsxSSIDConfigGroup OBJECT IDENTIFIER ::= { wlsxWlanConfigGroup 1 } wlsxAPConfigGroup OBJECT IDENTIFIER ::= { wlsxWlanConfigGroup 2 } wlsxWlanTotalNumAccessPoints OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Total Number of Access Points connected to the controller. " ::= { wlsxWlanAccessPointInfoGroup 1 } wlsxWlanTotalNumStationsAssociated OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Total Number of Stations Associated to the controller. " ::= { wlsxWlanAccessPointInfoGroup 2 } -- AP Group Table wlsxWlanAPGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanAPGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists all the Access Points Groups configured in the Aruba controller. " ::= { wlsxWlanAccessPointInfoGroup 3 } wlsxWlanAPGroupEntry OBJECT-TYPE SYNTAX WlanAPGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "AP Group Entry" INDEX {wlanAPGroup} ::= { wlsxWlanAPGroupTable 1 } WlanAPGroupEntry ::= SEQUENCE { wlanAPGroup DisplayString, wlanAPNumAps Integer32 } wlanAPGroup OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS not-accessible STATUS current DESCRIPTION " The name of an AP group " ::= { wlsxWlanAPGroupEntry 1 } wlanAPNumAps OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of APs in the AP Group " ::= { wlsxWlanAPGroupEntry 2 } -- AP Table wlsxWlanAPTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanAPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table lists all the Access Points connected to the controller. " ::= { wlsxWlanAccessPointInfoGroup 4 } wlsxWlanAPEntry OBJECT-TYPE SYNTAX WlanAPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access Point Entry" INDEX {wlanAPMacAddress} ::= { wlsxWlanAPTable 1 } WlanAPEntry ::= SEQUENCE { wlanAPMacAddress MacAddress, wlanAPIpAddress IpAddress, wlanAPName DisplayString, wlanAPGroupName DisplayString, wlanAPModel OBJECT IDENTIFIER, wlanAPSerialNumber DisplayString, wlanAPdot11aAntennaGain Integer32, wlanAPdot11gAntennaGain Integer32, wlanAPNumRadios Integer32, wlanAPEnet1Mode ArubaEnet1Mode, wlanAPIpsecMode ArubaEnableValue, wlanAPUpTime TimeTicks, wlanAPModelName DisplayString, wlanAPLocation DisplayString, wlanAPBuilding Integer32, wlanAPFloor Integer32, wlanAPLoc Integer32, wlanAPExternalAntenna ArubaAntennaSetting, wlanAPStatus ArubaAPStatus, wlanAPNumBootstraps Integer32, wlanAPNumReboots Integer32, wlanAPUnprovisioned ArubaUnprovisionedStatus, wlanAPMonitorMode ArubaMonitorMode, wlanAPFQLNBuilding DisplayString, wlanAPFQLNFloor DisplayString, wlanAPFQLN DisplayString, wlanAPFQLNCampus DisplayString, wlanAPLongitude DisplayString, wlanAPLatitude DisplayString, wlanAPAltitude DisplayString, wlanAPMeshRole ArubaMeshRole, wlanAPSysLocation DisplayString, wlanAPHwVersion DisplayString, wlanAPSwVersion DisplayString, wlanAPNumWarmReboots Integer32, wlanAPOuterIpAddress IpAddress, wlanAPRemoteLanIpAddress IpAddress, wlanAPActiveUplink INTEGER, wlanAPSwitchIpAddress IpAddress, wlanAPStandbyIpAddress IpAddress, wlanAPConnectedAsStandby INTEGER } wlanAPMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION " Ethernet MAC Address of the Access Point " ::= { wlsxWlanAPEntry 1 } wlanAPIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " IP Address of the Access Point " ::= { wlsxWlanAPEntry 2 } wlanAPName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION " Host name of the Access Point. " ::= { wlsxWlanAPEntry 3 } wlanAPGroupName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION " Group Name of the Access Point. " ::= { wlsxWlanAPEntry 4 } wlanAPModel OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION " Sys OID of the Access Point. " ::= { wlsxWlanAPEntry 5 } wlanAPSerialNumber OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION " Serial Number of the Access Point. " ::= { wlsxWlanAPEntry 6 } wlanAPdot11aAntennaGain OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Configured antenna gain for 'A' Radio. " ::= { wlsxWlanAPEntry 7 } wlanAPdot11gAntennaGain OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Configured antenna gain for 'G' Radio. " ::= { wlsxWlanAPEntry 8 } wlanAPNumRadios OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Number of Radios in the Access Point. " ::= { wlsxWlanAPEntry 9 } wlanAPEnet1Mode OBJECT-TYPE SYNTAX ArubaEnet1Mode MAX-ACCESS read-only STATUS current DESCRIPTION " Enet1 Mode of the Access Point. " ::= { wlsxWlanAPEntry 10 } wlanAPIpsecMode OBJECT-TYPE SYNTAX ArubaEnableValue MAX-ACCESS read-only STATUS current DESCRIPTION " IPSEC Mode of the Access Point. " ::= { wlsxWlanAPEntry 11 } wlanAPUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION " Time (in hundredths of seconds) since the last time the Access Point bootstrapped with the controller. " ::= { wlsxWlanAPEntry 12 } wlanAPModelName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " Model name of the Access Point. " ::= { wlsxWlanAPEntry 13 } wlanAPLocation OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " Location of the Access Point. " ::= { wlsxWlanAPEntry 14 } wlanAPBuilding OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " AP Building Number. " ::= { wlsxWlanAPEntry 15 } wlanAPFloor OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " AP Floor Number. " ::= { wlsxWlanAPEntry 16 } wlanAPLoc OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " AP Location. " ::= { wlsxWlanAPEntry 17 } wlanAPExternalAntenna OBJECT-TYPE SYNTAX ArubaAntennaSetting MAX-ACCESS read-only STATUS current DESCRIPTION " AP Antenna Status. " ::= { wlsxWlanAPEntry 18 } wlanAPStatus OBJECT-TYPE SYNTAX ArubaAPStatus MAX-ACCESS read-only STATUS current DESCRIPTION " AP Status. " ::= { wlsxWlanAPEntry 19 } wlanAPNumBootstraps OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Number of times the AP has bootstrapped with the controller. " ::= { wlsxWlanAPEntry 20 } wlanAPNumReboots OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Number of times the AP has rebooted. " ::= { wlsxWlanAPEntry 21 } wlanAPUnprovisioned OBJECT-TYPE SYNTAX ArubaUnprovisionedStatus MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates whether the AP is unprovisioned due to lack of antenna gain or location code settings. " ::= { wlsxWlanAPEntry 22 } wlanAPMonitorMode OBJECT-TYPE SYNTAX ArubaMonitorMode MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates whether any radio on this AP is acting as an air monitor. " ::= { wlsxWlanAPEntry 23 } wlanAPFQLNBuilding OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " The building component of the AP's FQLN. " ::= { wlsxWlanAPEntry 24 } wlanAPFQLNFloor OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " The floor component of the AP's FQLN. " ::= { wlsxWlanAPEntry 25 } wlanAPFQLN OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION " The AP's Fully Qualified Location Name (FQLN). " ::= { wlsxWlanAPEntry 26 } wlanAPFQLNCampus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " The campus component of the AP's FQLN. " ::= { wlsxWlanAPEntry 27 } wlanAPLongitude OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION " Longitude of the AP. Signed floating-point value. " ::= { wlsxWlanAPEntry 28 } wlanAPLatitude OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION " Latitude of the AP. Signed floating-point value. " ::= { wlsxWlanAPEntry 29 } wlanAPAltitude OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION " Altitude of the AP. Signed floating-point value. " ::= { wlsxWlanAPEntry 30 } wlanAPMeshRole OBJECT-TYPE SYNTAX ArubaMeshRole MAX-ACCESS read-write STATUS current DESCRIPTION " AP Mesh role " ::= { wlsxWlanAPEntry 31 } wlanAPSysLocation OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " AP sysLocation " ::= { wlsxWlanAPEntry 32 } wlanAPHwVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION " Hardware version of the AP. " ::= { wlsxWlanAPEntry 33 } wlanAPSwVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION " Software version of the AP. " ::= { wlsxWlanAPEntry 34 } wlanAPNumWarmReboots OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Number of times the AP has warm-rebooted. " ::= { wlsxWlanAPEntry 35 } wlanAPOuterIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Outer IP Address of the Access Point. " ::= { wlsxWlanAPEntry 36 } wlanAPRemoteLanIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " LAN IP Address of the Remote Access Point. " ::= { wlsxWlanAPEntry 37 } wlanAPActiveUplink OBJECT-TYPE SYNTAX INTEGER { ethernet(1), usb(2), pppoe(3) } MAX-ACCESS read-only STATUS current DESCRIPTION " Uplink of the RAP(Ethernet or USB). " ::= { wlsxWlanAPEntry 38 } wlanAPSwitchIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Access points' Serving Controller's IP Address. " ::= { wlsxWlanAPEntry 39 } wlanAPStandbyIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Access points' Standby Controller's IP Address. " ::= { wlsxWlanAPEntry 40 } wlanAPConnectedAsStandby OBJECT-TYPE SYNTAX INTEGER { active(0), standby(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " Access point connected as active/standby. " ::= { wlsxWlanAPEntry 41 } -- Radio table is indexed by the Mac Address of the AP and the type of the -- radio. wlsxWlanRadioTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table lists all the radios known to the controller. " ::= { wlsxWlanAccessPointInfoGroup 5 } wlsxWlanRadioEntry OBJECT-TYPE SYNTAX WlanRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "AP Radio Entry" INDEX {wlanAPMacAddress, wlanAPRadioNumber} ::= { wlsxWlanRadioTable 1 } WlanRadioEntry ::= SEQUENCE { wlanAPRadioNumber Integer32, wlanAPRadioType ArubaPhyType, wlanAPRadioChannel Integer32, wlanAPRadioTransmitPower Integer32, wlanAPRadioMode ArubaAccessPointMode, wlanAPRadioUtilization Integer32, wlanAPRadioNumAssociatedClients Integer32, wlanAPRadioNumMonitoredClients Integer32, wlanAPRadioNumActiveBSSIDs Integer32, wlanAPRadioNumMonitoredBSSIDs Integer32, wlanAPRadioBearing DisplayString, wlanAPRadioTiltAngle DisplayString, wlanAPRadioHTMode ArubaHTMode, wlanAPRadioHTExtChannel ArubaHTExtChannel, wlanAPRadioHTChannel DisplayString, wlanAPRadioAPName DisplayString } wlanAPRadioNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION " The radio number " ::= { wlsxWlanRadioEntry 1 } wlanAPRadioType OBJECT-TYPE SYNTAX ArubaPhyType MAX-ACCESS read-write STATUS current DESCRIPTION " Type of the Radio " ::= { wlsxWlanRadioEntry 2 } wlanAPRadioChannel OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The channel the radio is currently operating on. " ::= { wlsxWlanRadioEntry 3 } wlanAPRadioTransmitPower OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The current power level of the radio. " ::= { wlsxWlanRadioEntry 4 } wlanAPRadioMode OBJECT-TYPE SYNTAX ArubaAccessPointMode MAX-ACCESS read-only STATUS current DESCRIPTION " The Mode in which the radio is operating. " ::= { wlsxWlanRadioEntry 5 } wlanAPRadioUtilization OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The Utilization of the radio as a percentage of the total capacity. " ::= { wlsxWlanRadioEntry 6 } wlanAPRadioNumAssociatedClients OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of Clients associated to this radio. " ::= { wlsxWlanRadioEntry 7 } wlanAPRadioNumMonitoredClients OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of Clients this Radio is monitoring. " ::= { wlsxWlanRadioEntry 8 } wlanAPRadioNumActiveBSSIDs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of active BSSIDs on this Radio. " ::= { wlsxWlanRadioEntry 9 } wlanAPRadioNumMonitoredBSSIDs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of AP BSSIDs this radio is monitoring. " ::= { wlsxWlanRadioEntry 10 } wlanAPRadioBearing OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION " Antenna Bearing in degrees from True North. Unsigned floating-point value. Range: 0-360. " ::= { wlsxWlanRadioEntry 11 } wlanAPRadioTiltAngle OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION " Tilt angle of antenna in degrees. -ve for downtilt, +ve for uptilt. Signed floating-point value. Range: -90 to +90. " ::= { wlsxWlanRadioEntry 12 } wlanAPRadioHTMode OBJECT-TYPE SYNTAX ArubaHTMode MAX-ACCESS read-only STATUS current DESCRIPTION " The HT mode of the radio, if any. " ::= { wlsxWlanRadioEntry 13 } wlanAPRadioHTExtChannel OBJECT-TYPE SYNTAX ArubaHTExtChannel MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates the offset of the 40MHz extension channel, if any. " ::= { wlsxWlanRadioEntry 14 } wlanAPRadioHTChannel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION " A display string indicating the current channel. If wlanAPRadioHTExtChannel is set to 'above' or 'below', then the channel number will be appended with '+' or '-' respectively. " ::= { wlsxWlanRadioEntry 15 } wlanAPRadioAPName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Name of the AP the radio belongs to" ::= { wlsxWlanRadioEntry 16 } -- Local Access Point Table. wlsxWlanAPBssidTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanAPBssidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table lists all the BSSIDs active on this controller. " ::= { wlsxWlanAccessPointInfoGroup 7 } wlsxWlanAPBssidEntry OBJECT-TYPE SYNTAX WlanAPBssidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "BSSID Entry" INDEX {wlanAPMacAddress, wlanAPRadioNumber, wlanAPBSSID} ::= { wlsxWlanAPBssidTable 1 } WlanAPBssidEntry ::= SEQUENCE { wlanAPBSSID MacAddress, wlanAPESSID DisplayString, wlanAPBssidSlot Unsigned32, wlanAPBssidPort Unsigned32, wlanAPBssidPhyType ArubaPhyType, wlanAPBssidRogueType ArubaRogueApType, wlanAPBssidMode INTEGER, wlanAPBssidChannel INTEGER, wlanAPBssidUpTime TimeTicks, wlanAPBssidInactiveTime TimeTicks, wlanAPBssidLoadBalancing TruthValue, wlanAPBssidNumAssociatedStations Unsigned32, wlanAPBssidAPMacAddress MacAddress, wlanAPBssidPhyNumber Integer32, wlanAPBssidHTMode ArubaHTMode, wlanAPBssidHTExtChannel ArubaHTExtChannel, wlanAPBssidHTChannel DisplayString, wlanAPBssidSnr Integer32 } wlanAPBSSID OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION " The MAC address of the Access Point. " ::= { wlsxWlanAPBssidEntry 1 } wlanAPESSID OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION " ESSID this BSSID is advertising. " ::= { wlsxWlanAPBssidEntry 2 } wlanAPBssidSlot OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Slot to which the Access Point is connected. " ::= { wlsxWlanAPBssidEntry 3 } wlanAPBssidPort OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Port to which the Access Point is connected. " ::= { wlsxWlanAPBssidEntry 4 } wlanAPBssidPhyType OBJECT-TYPE SYNTAX ArubaPhyType MAX-ACCESS read-only STATUS current DESCRIPTION " Physical Layer Protocol support of the AP. " ::= { wlsxWlanAPBssidEntry 5 } wlanAPBssidRogueType OBJECT-TYPE SYNTAX ArubaRogueApType MAX-ACCESS read-only STATUS current DESCRIPTION " The type of the Rogue. " ::= { wlsxWlanAPBssidEntry 6 } wlanAPBssidMode OBJECT-TYPE SYNTAX INTEGER{ ap(1), am(2), mpp(3), mp(4) } MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates whether the Access point is an Air Monitor or regular AP or Mesh Portal or Mesh Point. " ::= { wlsxWlanAPBssidEntry 7 } wlanAPBssidChannel OBJECT-TYPE SYNTAX INTEGER(1..165) MAX-ACCESS read-only STATUS current DESCRIPTION " The current operating channel. " ::= { wlsxWlanAPBssidEntry 8 } wlanAPBssidUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION " Time (in hundredths of seconds) since the tunnel was created between the access point and controller " ::= { wlsxWlanAPBssidEntry 9 } wlanAPBssidInactiveTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION " Time (in hundredths of seconds) since any activity took place on the BSSID. " ::= { wlsxWlanAPBssidEntry 10 } wlanAPBssidLoadBalancing OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates whether load balancing is enabled or not. " ::= { wlsxWlanAPBssidEntry 11 } wlanAPBssidNumAssociatedStations OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates the number of stations associated to this BSSID. " ::= { wlsxWlanAPBssidEntry 12 } wlanAPBssidAPMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates the Access Point to which this BSSID belongs. " ::= { wlsxWlanAPBssidEntry 13 } wlanAPBssidPhyNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates the radio number to which this BSSID belongs. " ::= { wlsxWlanAPBssidEntry 14 } wlanAPBssidHTMode OBJECT-TYPE SYNTAX ArubaHTMode MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates the HT mode of this BSSID, if any. " ::= { wlsxWlanAPBssidEntry 15 } wlanAPBssidHTExtChannel OBJECT-TYPE SYNTAX ArubaHTExtChannel MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates the offset of the 40MHz extension channel, if any. " ::= { wlsxWlanAPBssidEntry 16 } wlanAPBssidHTChannel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " A display string indicating the current channel. If wlanAPBssidHTExtChannel is set to 'above' or 'below', then the channel number will be appended with '+' or '-' respectively. " ::= { wlsxWlanAPBssidEntry 17 } wlanAPBssidSnr OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates the Signal Noise Ratio of this BSSID. " ::= { wlsxWlanAPBssidEntry 18 } -- ESSID Table wlsxWlanESSIDTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanESSIDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists all the ESSIDs advertised by this controller. " ::= { wlsxWlanAccessPointInfoGroup 8 } wlsxWlanESSIDEntry OBJECT-TYPE SYNTAX WlanESSIDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "ESSID Entry" INDEX {wlanESSID} ::= { wlsxWlanESSIDTable 1 } WlanESSIDEntry ::= SEQUENCE { wlanESSID DisplayString, wlanESSIDNumStations Unsigned32, wlanESSIDNumAccessPointsUp Unsigned32, wlanESSIDNumAccessPointsDown Unsigned32, wlanESSIDEncryptionType ArubaEncryptionMethods } wlanESSID OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION " The ESSID being advertised. " ::= { wlsxWlanESSIDEntry 1 } wlanESSIDNumStations OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of stations connected to this ESSID. " ::= { wlsxWlanESSIDEntry 2 } wlanESSIDNumAccessPointsUp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of APs currently advertising this ESSID. " ::= { wlsxWlanESSIDEntry 3 } wlanESSIDNumAccessPointsDown OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of APs configured to advertise this ESSID that are not currently operational. " ::= { wlsxWlanESSIDEntry 4 } wlanESSIDEncryptionType OBJECT-TYPE SYNTAX ArubaEncryptionMethods MAX-ACCESS read-only STATUS current DESCRIPTION " The encryption methods supported on this ESSID. " ::= { wlsxWlanESSIDEntry 5 } -- ESSID Vlan Pool Table wlsxWlanESSIDVlanPoolTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanESSIDVlanPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists all the VLANs associated with this ESSID. " ::= { wlsxWlanAccessPointInfoGroup 9 } wlsxWlanESSIDVlanPoolEntry OBJECT-TYPE SYNTAX WlanESSIDVlanPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "ESSID Vlan Pool Entry" INDEX {wlanESSID, wlanESSIDVlanId} ::= { wlsxWlanESSIDVlanPoolTable 1 } WlanESSIDVlanPoolEntry ::= SEQUENCE { wlanESSIDVlanId Unsigned32, wlanESSIDVlanPoolStatus RowStatus } wlanESSIDVlanId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION " VLAN which is part of the VLAN pool for this ESSID. " ::= { wlsxWlanESSIDVlanPoolEntry 1 } wlanESSIDVlanPoolStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " Row status object used to indicate the status of the row. " ::= { wlsxWlanESSIDVlanPoolEntry 2 } --Station Info Group contains the State information for the stations. --Station Table contains all the station associated with an AP. wlsxWlanStationTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanStationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists all the wireless stations associated with the Access points connected to this controller. " ::= { wlsxWlanStationInfoGroup 1} wlsxWlanStationEntry OBJECT-TYPE SYNTAX WlanStationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Station Entry" INDEX {wlanStaPhyAddress} ::= { wlsxWlanStationTable 1 } WlanStationEntry ::= SEQUENCE { wlanStaPhyAddress MacAddress, wlanStaApBssid MacAddress, wlanStaPhyType ArubaPhyType, wlanStaIsAuthenticated TruthValue, wlanStaIsAssociated TruthValue, wlanStaChannel INTEGER, wlanStaVlanId ArubaVlanValidRange, wlanStaVOIPState TruthValue, wlanStaVOIPProtocol ArubaVoipProtocolType, wlanStaTransmitRate Unsigned32, wlanStaAssociationID Unsigned32, wlanStaAccessPointESSID DisplayString, wlanStaPhyNumber Integer32, wlanStaRSSI Integer32, wlanStaUpTime TimeTicks, wlanStaHTMode ArubaHTMode, wlanStaTransmitRateCode Unsigned32 } wlanStaPhyAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION " The Physical Address of the Station. " ::= { wlsxWlanStationEntry 1 } wlanStaApBssid OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION " The Access point to which this station last associated to. " ::= { wlsxWlanStationEntry 2 } wlanStaPhyType OBJECT-TYPE SYNTAX ArubaPhyType MAX-ACCESS read-only STATUS current DESCRIPTION " Type of the Station. " ::= { wlsxWlanStationEntry 3 } wlanStaIsAuthenticated OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates whether the station is authenticated. " ::= { wlsxWlanStationEntry 4 } wlanStaIsAssociated OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates whether the station is associated. " ::= { wlsxWlanStationEntry 5 } wlanStaChannel OBJECT-TYPE SYNTAX INTEGER(1..165) MAX-ACCESS read-only STATUS current DESCRIPTION " Channel on which the station is associated. " ::= { wlsxWlanStationEntry 6 } wlanStaVlanId OBJECT-TYPE SYNTAX ArubaVlanValidRange MAX-ACCESS read-only STATUS current DESCRIPTION " VLAN in which the station is present. " ::= { wlsxWlanStationEntry 7 } wlanStaVOIPState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION " The State of VoIP for this station. " ::= { wlsxWlanStationEntry 8 } wlanStaVOIPProtocol OBJECT-TYPE SYNTAX ArubaVoipProtocolType MAX-ACCESS read-only STATUS current DESCRIPTION " If VoIP is enabled, the type of the protocol supported. " ::= { wlsxWlanStationEntry 9 } wlanStaTransmitRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Transmit rate with which the Station is associated with this system. " ::= { wlsxWlanStationEntry 10 } wlanStaAssociationID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " AID with which the Station is associated with this system. " ::= { wlsxWlanStationEntry 11 } wlanStaAccessPointESSID OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION " ESSID of the Access point " ::= { wlsxWlanStationEntry 12 } wlanStaPhyNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Radio PHY number to which the station is associated " ::= { wlsxWlanStationEntry 13 } wlanStaRSSI OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Signal to Noise ratio for the station. " ::= { wlsxWlanStationEntry 14 } wlanStaUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION " Time since the station associated to the current BSSID. " ::= { wlsxWlanStationEntry 15 } wlanStaHTMode OBJECT-TYPE SYNTAX ArubaHTMode MAX-ACCESS read-only STATUS current DESCRIPTION " The HT status of the station. " ::= { wlsxWlanStationEntry 16 } wlanStaTransmitRateCode OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Transmit rate code with which the Station is associated with this system, unit is mbps. " ::= { wlsxWlanStationEntry 17 } --Station Association Failure Table contains all the Stations that failed to --associate an ap. wlsxWlanStaAssociationFailureTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanStaAssociationFailureEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists all the stations and the BSSID's to which they failed to associate. Once a station successfully associates, association failure entries are not reported for that station. " ::= { wlsxWlanStationInfoGroup 2} wlsxWlanStaAssociationFailureEntry OBJECT-TYPE SYNTAX WlanStaAssociationFailureEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Station Association Failure Entry" INDEX {wlanStaPhyAddress, wlanAPBSSID} ::= { wlsxWlanStaAssociationFailureTable 1 } WlanStaAssociationFailureEntry ::= SEQUENCE { wlanStaAssocFailureApName DisplayString, wlanStaAssocFailureApEssid DisplayString, wlanStaAssocFailurePhyNum Integer32, wlanStaAssocFailurePhyType ArubaPhyType, wlanStaAssocFailureElapsedTime TimeTicks, wlanStaAssocFailureReason DisplayString } wlanStaAssocFailureApName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION " Name of the Access Point to which this station tried to associate. " ::= { wlsxWlanStaAssociationFailureEntry 1 } wlanStaAssocFailureApEssid OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION " ESSID to which the station association failed. " ::= { wlsxWlanStaAssociationFailureEntry 2 } wlanStaAssocFailurePhyNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " Radio PHY number to which the station tried to associate. " ::= { wlsxWlanStaAssociationFailureEntry 3 } wlanStaAssocFailurePhyType OBJECT-TYPE SYNTAX ArubaPhyType MAX-ACCESS read-only STATUS current DESCRIPTION " Radio PHY Type of the Station. " ::= { wlsxWlanStaAssociationFailureEntry 4 } wlanStaAssocFailureElapsedTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION " Elapsed time in timeticks after the station's failure to associate. " ::= { wlsxWlanStaAssociationFailureEntry 5 } wlanStaAssocFailureReason OBJECT-TYPE SYNTAX DisplayString(SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION " Reason for the Station association failure " ::= { wlsxWlanStaAssociationFailureEntry 6 } -- Stats group contains tables for station statistics, BSSID statistics and -- AP statistics. wlsxWlanAPStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanAPStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists the statistics of all the Access Points connected to the controller. " ::= { wlsxWlanAccessPointStatsGroup 1 } wlsxWlanAPStatsEntry OBJECT-TYPE SYNTAX WlanAPStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access Point Stats entry" INDEX {wlanAPMacAddress, wlanAPRadioNumber, wlanAPBSSID} ::= { wlsxWlanAPStatsTable 1 } WlanAPStatsEntry ::= SEQUENCE { wlanAPCurrentChannel Unsigned32, wlanAPNumClients Integer32, wlanAPTxPkts Counter32, wlanAPTxBytes Counter32, wlanAPRxPkts Counter32, wlanAPRxBytes Counter32, wlanAPTxDeauthentications Counter32, wlanAPRxDeauthentications Counter32, wlanAPChannelThroughput Integer32, wlanAPFrameRetryRate Integer32, wlanAPFrameLowSpeedRate Integer32, wlanAPFrameNonUnicastRate Integer32, wlanAPFrameFragmentationRate Integer32, wlanAPFrameBandwidthRate Integer32, wlanAPFrameRetryErrorRate Integer32, wlanAPChannelErrorRate Integer32, wlanAPFrameReceiveErrorRate Integer32, wlanAPRxDataPkts Counter32, wlanAPRxDataBytes Counter32, wlanAPTxDataPkts Counter32, wlanAPTxDataBytes Counter32, wlanAPRxDataPkts64 Counter64, wlanAPRxDataBytes64 Counter64, wlanAPTxDataPkts64 Counter64, wlanAPTxDataBytes64 Counter64, wlanAPWiredRxErrorPkts Counter32, wlanAPRxErrorPkts Counter32 } wlanAPCurrentChannel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " The channel the AP is currently using. " ::= { wlsxWlanAPStatsEntry 1 } wlanAPNumClients OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of clients associated to this BSSID. " ::= { wlsxWlanAPStatsEntry 2 } wlanAPTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of packets transmitted on this BSSID. " ::= { wlsxWlanAPStatsEntry 3 } wlanAPTxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of bytes transmitted on this BSSID. " ::= { wlsxWlanAPStatsEntry 4 } wlanAPRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of packets received on this BSSID. " ::= { wlsxWlanAPStatsEntry 5 } wlanAPRxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of bytes received on this BSSID. " ::= { wlsxWlanAPStatsEntry 6 } wlanAPTxDeauthentications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of deauthentications transmitted on this BSSID. " ::= { wlsxWlanAPStatsEntry 7 } wlanAPRxDeauthentications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of deauthentications received on this BSSID. " ::= { wlsxWlanAPStatsEntry 8 } wlanAPChannelThroughput OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The throughput achieved on this channel. " ::= { wlsxWlanAPStatsEntry 9 } wlanAPFrameRetryRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of retry packets as a percentage of the total packets transmitted and received by this BSSID. " ::= { wlsxWlanAPStatsEntry 10 } wlanAPFrameLowSpeedRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of low data rate (<= 18Mbps for A/G bands and <=2Mbps for B band) packets as a percentage of the total packets transmitted and received by this BSSID " ::= { wlsxWlanAPStatsEntry 11 } wlanAPFrameNonUnicastRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of broadcast and multicast packets as a percentage of the total packets transmitted on this BSSIDchannel. " ::= { wlsxWlanAPStatsEntry 12 } wlanAPFrameFragmentationRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of fragments as a percentage of the total packets transmitted by this BSSID. " ::= { wlsxWlanAPStatsEntry 13 } wlanAPFrameBandwidthRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The bandwidth of this BSSID in Kbps. " ::= { wlsxWlanAPStatsEntry 14 } wlanAPFrameRetryErrorRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of error packets as a percentage of the total packets received on this BSSID. " ::= { wlsxWlanAPStatsEntry 15 } wlanAPChannelErrorRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of error packets as a percentage of the total packets received on the current channel. " ::= { wlsxWlanAPStatsEntry 16 } wlanAPFrameReceiveErrorRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of error packets as a percentage of the total packets received on this BSSID. " ::= { wlsxWlanAPStatsEntry 17 } wlanAPRxDataPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION " The number of packets received on this BSSID. " ::= { wlsxWlanAPStatsEntry 18 } wlanAPRxDataBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION " The number of bytes received on this BSSID. " ::= { wlsxWlanAPStatsEntry 19 } wlanAPTxDataPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION " The number of packets transmitted on this BSSID. " ::= { wlsxWlanAPStatsEntry 20 } wlanAPTxDataBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION " The number of bytes transmitted on this BSSID. " ::= { wlsxWlanAPStatsEntry 21 } wlanAPRxDataPkts64 OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of packets received on this BSSID. " ::= { wlsxWlanAPStatsEntry 22 } wlanAPRxDataBytes64 OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of bytes received on this BSSID. " ::= { wlsxWlanAPStatsEntry 23 } wlanAPTxDataPkts64 OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of packets transmitted on this BSSID. " ::= { wlsxWlanAPStatsEntry 24 } wlanAPTxDataBytes64 OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of bytes transmitted on this BSSID. " ::= { wlsxWlanAPStatsEntry 25 } wlanAPWiredRxErrorPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of error packets received from the controller on this BSSID. " ::= { wlsxWlanAPStatsEntry 26 } wlanAPRxErrorPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of error packets received from stations on this BSSID. " ::= { wlsxWlanAPStatsEntry 27 } -- This table breaks down the AP statistics observed into different -- rate categories. wlsxWlanAPRateStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlsxWlanAPRateStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table contains all the AP Packet and Byte Counts but represented in terms of rate categories. " ::= { wlsxWlanAccessPointStatsGroup 2 } wlsxWlanAPRateStatsEntry OBJECT-TYPE SYNTAX WlsxWlanAPRateStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Data rate based packet and byte count entry for an AP" INDEX {wlanAPMacAddress, wlanAPRadioNumber, wlanAPBSSID} ::= { wlsxWlanAPRateStatsTable 1 } WlsxWlanAPRateStatsEntry ::= SEQUENCE { wlanAPStatsTotPktsAt1Mbps Counter32, wlanAPStatsTotBytesAt1Mbps Counter32, wlanAPStatsTotPktsAt2Mbps Counter32, wlanAPStatsTotBytesAt2Mbps Counter32, wlanAPStatsTotPktsAt5Mbps Counter32, wlanAPStatsTotBytesAt5Mbps Counter32, wlanAPStatsTotPktsAt11Mbps Counter32, wlanAPStatsTotBytesAt11Mbps Counter32, wlanAPStatsTotPktsAt6Mbps Counter32, wlanAPStatsTotBytesAt6Mbps Counter32, wlanAPStatsTotPktsAt12Mbps Counter32, wlanAPStatsTotBytesAt12Mbps Counter32, wlanAPStatsTotPktsAt18Mbps Counter32, wlanAPStatsTotBytesAt18Mbps Counter32, wlanAPStatsTotPktsAt24Mbps Counter32, wlanAPStatsTotBytesAt24Mbps Counter32, wlanAPStatsTotPktsAt36Mbps Counter32, wlanAPStatsTotBytesAt36Mbps Counter32, wlanAPStatsTotPktsAt48Mbps Counter32, wlanAPStatsTotBytesAt48Mbps Counter32, wlanAPStatsTotPktsAt54Mbps Counter32, wlanAPStatsTotBytesAt54Mbps Counter32, wlanAPStatsTotPktsAt9Mbps Counter32, wlanAPStatsTotBytesAt9Mbps Counter32 -- wlanAPStatsTotPktsAtHT6dot5Mbps Counter32, -- wlanAPStatsTotBytesAtHT6dot5Mbps Counter32, -- wlanAPStatsTotPktsAtHT13Mbps Counter32, -- wlanAPStatsTotBytesAtHT13Mbps Counter32, -- wlanAPStatsTotPktsAtHT13dot5Mbps Counter32, -- wlanAPStatsTotBytesAtHT13dot5Mbps Counter32, -- wlanAPStatsTotPktsAtHT15Mbps Counter32, -- wlanAPStatsTotBytesAtHT15Mbps Counter32, -- wlanAPStatsTotPktsAtHT19dot5Mbps Counter32, -- wlanAPStatsTotBytesAtHT19dot5Mbps Counter32, -- wlanAPStatsTotPktsAtHT26Mbps Counter32, -- wlanAPStatsTotBytesAtHT26Mbps Counter32, -- wlanAPStatsTotPktsAtHT27Mbps Counter32, -- wlanAPStatsTotBytesAtHT27Mbps Counter32, -- wlanAPStatsTotPktsAtHT30Mbps Counter32, -- wlanAPStatsTotBytesAtHT30Mbps Counter32, -- wlanAPStatsTotPktsAtHT39Mbps Counter32, -- wlanAPStatsTotBytesAtHT39Mbps Counter32, -- wlanAPStatsTotPktsAtHT40dot5Mbps Counter32, -- wlanAPStatsTotBytesAtHT40dot5Mbps Counter32, -- wlanAPStatsTotPktsAtHT45Mbps Counter32, -- wlanAPStatsTotBytesAtHT45Mbps Counter32, -- wlanAPStatsTotPktsAtHT52Mbps Counter32, -- wlanAPStatsTotBytesAtHT52Mbps Counter32, -- wlanAPStatsTotPktsAtHT54Mbps Counter32, -- wlanAPStatsTotBytesAtHT54Mbps Counter32, -- wlanAPStatsTotPktsAtHT58dot5Mbps Counter32, -- wlanAPStatsTotBytesAtHT58dot5Mbps Counter32, -- wlanAPStatsTotPktsAtHT60Mbps Counter32, -- wlanAPStatsTotBytesAtHT60Mbps Counter32, -- wlanAPStatsTotPktsAtHT65Mbps Counter32, -- wlanAPStatsTotBytesAtHT65Mbps Counter32, -- wlanAPStatsTotPktsAtHT78Mbps Counter32, -- wlanAPStatsTotBytesAtHT78Mbps Counter32, -- wlanAPStatsTotPktsAtHT81Mbps Counter32, -- wlanAPStatsTotBytesAtHT81Mbps Counter32, -- wlanAPStatsTotPktsAtHT90Mbps Counter32, -- wlanAPStatsTotBytesAtHT90Mbps Counter32, -- wlanAPStatsTotPktsAtHT104Mbps Counter32, -- wlanAPStatsTotBytesAtHT104Mbps Counter32, -- wlanAPStatsTotPktsAtHT108Mbps Counter32, -- wlanAPStatsTotBytesAtHT108Mbps Counter32, -- wlanAPStatsTotPktsAtHT117Mbps Counter32, -- wlanAPStatsTotBytesAtHT117Mbps Counter32, -- wlanAPStatsTotPktsAtHT120Mbps Counter32, -- wlanAPStatsTotBytesAtHT120Mbps Counter32, -- wlanAPStatsTotPktsAtHT121dot5Mbps Counter32, -- wlanAPStatsTotBytesAtHT121dot5Mbps Counter32, -- wlanAPStatsTotPktsAtHT130Mbps Counter32, -- wlanAPStatsTotBytesAtHT130Mbps Counter32, -- wlanAPStatsTotPktsAtHT135Mbps Counter32, -- wlanAPStatsTotBytesAtHT135Mbps Counter32, -- wlanAPStatsTotPktsAtHT150Mbps Counter32, -- wlanAPStatsTotBytesAtHT150Mbps Counter32, -- wlanAPStatsTotPktsAtHT162Mbps Counter32, -- wlanAPStatsTotBytesAtHT162Mbps Counter32, -- wlanAPStatsTotPktsAtHT180Mbps Counter32, -- wlanAPStatsTotBytesAtHT180Mbps Counter32, -- wlanAPStatsTotPktsAtHT216Mbps Counter32, -- wlanAPStatsTotBytesAtHT216Mbps Counter32, -- wlanAPStatsTotPktsAtHT240Mbps Counter32, -- wlanAPStatsTotBytesAtHT240Mbps Counter32, -- wlanAPStatsTotPktsAtHT243Mbps Counter32, -- wlanAPStatsTotBytesAtHT243Mbps Counter32, -- wlanAPStatsTotPktsAtHT270Mbps Counter32, -- wlanAPStatsTotBytesAtHT270Mbps Counter32, -- wlanAPStatsTotPktsAtHT300Mbps Counter32, -- wlanAPStatsTotBytesAtHT300Mbps Counter32 } wlanAPStatsTotPktsAt1Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 1Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 1 } wlanAPStatsTotBytesAt1Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 1Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 2 } wlanAPStatsTotPktsAt2Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 2Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 3 } wlanAPStatsTotBytesAt2Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 2Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 4 } wlanAPStatsTotPktsAt5Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 5Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 5 } wlanAPStatsTotBytesAt5Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 5Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 6 } wlanAPStatsTotPktsAt11Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 11Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 7 } wlanAPStatsTotBytesAt11Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 11Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 8 } wlanAPStatsTotPktsAt6Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 6Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 9 } wlanAPStatsTotBytesAt6Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 6Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 10 } wlanAPStatsTotPktsAt12Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 12Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 11 } wlanAPStatsTotBytesAt12Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 12Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 12 } wlanAPStatsTotPktsAt18Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 18Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 13 } wlanAPStatsTotBytesAt18Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 18Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 14 } wlanAPStatsTotPktsAt24Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 24Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 15 } wlanAPStatsTotBytesAt24Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 24Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 16 } wlanAPStatsTotPktsAt36Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 36Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 17 } wlanAPStatsTotBytesAt36Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 36Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 18 } wlanAPStatsTotPktsAt48Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 48Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 19 } wlanAPStatsTotBytesAt48Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 48Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 20 } wlanAPStatsTotPktsAt54Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 54Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 21 } wlanAPStatsTotBytesAt54Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 54Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 22 } wlanAPStatsTotPktsAt9Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets observed on this BSSID at 9Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 23 } wlanAPStatsTotBytesAt9Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Bytes observed on this BSSID at 9Mbps rate. " ::= { wlsxWlanAPRateStatsEntry 24 } -- wlanAPStatsTotPktsAtHT6dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 6.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 25 } -- -- wlanAPStatsTotBytesAtHT6dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 6.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 26 } -- -- wlanAPStatsTotPktsAtHT13Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 13.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 27 } -- -- wlanAPStatsTotBytesAtHT13Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 13.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 28 } -- -- wlanAPStatsTotPktsAtHT13dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 13.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 29 } -- -- wlanAPStatsTotBytesAtHT13dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 13.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 30 } -- -- wlanAPStatsTotPktsAtHT15Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 15.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 31 } -- -- wlanAPStatsTotBytesAtHT15Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 15.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 32 } -- -- wlanAPStatsTotPktsAtHT19dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 19.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 33 } -- -- wlanAPStatsTotBytesAtHT19dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 19.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 34 } -- -- wlanAPStatsTotPktsAtHT26Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 26.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 35 } -- -- wlanAPStatsTotBytesAtHT26Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 26.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 36 } -- -- wlanAPStatsTotPktsAtHT27Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 27.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 37 } -- -- wlanAPStatsTotBytesAtHT27Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 27.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 38 } -- -- wlanAPStatsTotPktsAtHT30Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 30.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 39 } -- -- wlanAPStatsTotBytesAtHT30Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 30.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 40 } -- -- wlanAPStatsTotPktsAtHT39Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 39.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 41 } -- -- wlanAPStatsTotBytesAtHT39Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 39.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 42 } -- -- wlanAPStatsTotPktsAtHT40dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 40.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 43 } -- -- wlanAPStatsTotBytesAtHT40dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 40.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 44 } -- -- wlanAPStatsTotPktsAtHT45Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 45.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 45 } -- -- wlanAPStatsTotBytesAtHT45Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 45.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 46 } -- -- wlanAPStatsTotPktsAtHT52Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 52.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 47 } -- -- wlanAPStatsTotBytesAtHT52Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 52.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 48 } -- -- wlanAPStatsTotPktsAtHT54Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 54.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 49 } -- -- wlanAPStatsTotBytesAtHT54Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 54.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 50 } -- -- wlanAPStatsTotPktsAtHT58dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 58.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 51 } -- -- wlanAPStatsTotBytesAtHT58dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 58.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 52 } -- -- wlanAPStatsTotPktsAtHT60Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 60.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 53 } -- -- wlanAPStatsTotBytesAtHT60Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 60.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 54 } -- -- wlanAPStatsTotPktsAtHT65Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 65.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 55 } -- -- wlanAPStatsTotBytesAtHT65Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 65.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 56 } -- -- wlanAPStatsTotPktsAtHT78Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 78.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 57 } -- -- wlanAPStatsTotBytesAtHT78Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 78.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 58 } -- -- wlanAPStatsTotPktsAtHT81Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 81.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 59 } -- -- wlanAPStatsTotBytesAtHT81Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 81.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 60 } -- -- wlanAPStatsTotPktsAtHT90Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 90.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 61 } -- -- wlanAPStatsTotBytesAtHT90Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 90.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 62 } -- -- wlanAPStatsTotPktsAtHT104Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 104.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 63 } -- -- wlanAPStatsTotBytesAtHT104Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 104.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 64 } -- -- wlanAPStatsTotPktsAtHT108Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 108.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 65 } -- -- wlanAPStatsTotBytesAtHT108Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 108.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 66 } -- -- wlanAPStatsTotPktsAtHT117Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 117.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 67 } -- -- wlanAPStatsTotBytesAtHT117Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 117.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 68 } -- -- wlanAPStatsTotPktsAtHT120Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 120.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 69 } -- -- wlanAPStatsTotBytesAtHT120Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 120.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 70 } -- -- wlanAPStatsTotPktsAtHT121dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 121.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 71 } -- -- wlanAPStatsTotBytesAtHT121dot5Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 121.5 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 72 } -- -- wlanAPStatsTotPktsAtHT130Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 130.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 73 } -- -- wlanAPStatsTotBytesAtHT130Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 130.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 74 } -- -- wlanAPStatsTotPktsAtHT135Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 135.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 75 } -- -- wlanAPStatsTotBytesAtHT135Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 135.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 76 } -- -- wlanAPStatsTotPktsAtHT150Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 150.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 77 } -- -- wlanAPStatsTotBytesAtHT150Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 150.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 78 } -- -- wlanAPStatsTotPktsAtHT162Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 162.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 79 } -- -- wlanAPStatsTotBytesAtHT162Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 162.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 80 } -- -- wlanAPStatsTotPktsAtHT180Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 180.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 81 } -- -- wlanAPStatsTotBytesAtHT180Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 180.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 82 } -- -- wlanAPStatsTotPktsAtHT216Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 216.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 83 } -- -- wlanAPStatsTotBytesAtHT216Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 216.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 84 } -- -- wlanAPStatsTotPktsAtHT240Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 240.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 85 } -- -- wlanAPStatsTotBytesAtHT240Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 240.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 86 } -- -- wlanAPStatsTotPktsAtHT243Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 243.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 87 } -- -- wlanAPStatsTotBytesAtHT243Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 243.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 88 } -- -- wlanAPStatsTotPktsAtHT270Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 270.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 89 } -- -- wlanAPStatsTotBytesAtHT270Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 270.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 90 } -- -- wlanAPStatsTotPktsAtHT300Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of packets observed -- on this BSSID at the HT 300.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 91 } -- -- wlanAPStatsTotBytesAtHT300Mbps OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- " -- This attribute indicates the total number of bytes observed -- on this BSSID at the HT 300.0 rate. -- " -- ::= { wlsxWlanAPRateStatsEntry 92 } -- This table breaks down the BSSID statistics observed based on the -- Destination Address Types. wlsxWlanAPDATypeStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlsxWlanAPDATypeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table contains all the per BSSID Packet and Byte Counts but broken down in terms of Destination Address Type. " ::= { wlsxWlanAccessPointStatsGroup 3 } wlsxWlanAPDATypeStatsEntry OBJECT-TYPE SYNTAX WlsxWlanAPDATypeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Destination Address based packet and byte count entry for an AP" INDEX {wlanAPMacAddress, wlanAPRadioNumber, wlanAPBSSID} ::= { wlsxWlanAPDATypeStatsTable 1 } WlsxWlanAPDATypeStatsEntry ::= SEQUENCE { wlanAPStatsTotDABroadcastPkts Counter32 , wlanAPStatsTotDABroadcastBytes Counter32 , wlanAPStatsTotDAMulticastPkts Counter32 , wlanAPStatsTotDAMulticastBytes Counter32 , wlanAPStatsTotDAUnicastPkts Counter32 , wlanAPStatsTotDAUnicastBytes Counter32 } wlanAPStatsTotDABroadcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Broadcast packets observed on this BSSID. " ::= { wlsxWlanAPDATypeStatsEntry 1 } wlanAPStatsTotDABroadcastBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Broadcast Bytes observed on this BSSID. " ::= { wlsxWlanAPDATypeStatsEntry 2 } wlanAPStatsTotDAMulticastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Multicast packets observed on this BSSID. " ::= { wlsxWlanAPDATypeStatsEntry 3 } wlanAPStatsTotDAMulticastBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Multicast Bytes observed on this BSSID. " ::= { wlsxWlanAPDATypeStatsEntry 4 } wlanAPStatsTotDAUnicastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Unicast packets observed on this BSSID. " ::= { wlsxWlanAPDATypeStatsEntry 5 } wlanAPStatsTotDAUnicastBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Unicast Bytes observed on this BSSID. " ::= { wlsxWlanAPDATypeStatsEntry 6 } -- This table breaks down the BSSID statistics observed based on the -- the Type of the Packet. wlsxWlanAPFrameTypeStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlsxWlanAPFrameTypeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table contains all the per BSSID Packet and Byte Counts but broken down into different Frame Types. " ::= { wlsxWlanAccessPointStatsGroup 4 } wlsxWlanAPFrameTypeStatsEntry OBJECT-TYPE SYNTAX WlsxWlanAPFrameTypeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Frame Type based packet and byte count entry for an AP" INDEX {wlanAPMacAddress, wlanAPRadioNumber, wlanAPBSSID} ::= { wlsxWlanAPFrameTypeStatsTable 1 } WlsxWlanAPFrameTypeStatsEntry ::= SEQUENCE { wlanAPStatsTotMgmtPkts Counter32 , wlanAPStatsTotMgmtBytes Counter32 , wlanAPStatsTotCtrlPkts Counter32 , wlanAPStatsTotCtrlBytes Counter32 , wlanAPStatsTotDataPkts Counter32 , wlanAPStatsTotDataBytes Counter32 } wlanAPStatsTotMgmtPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Management packets observed on this BSSID. " ::= { wlsxWlanAPFrameTypeStatsEntry 1 } wlanAPStatsTotMgmtBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Management Bytes observed on this BSSID. " ::= { wlsxWlanAPFrameTypeStatsEntry 2 } wlanAPStatsTotCtrlPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Control packets observed on this BSSID. " ::= { wlsxWlanAPFrameTypeStatsEntry 3 } wlanAPStatsTotCtrlBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Control Bytes observed on this BSSID. " ::= { wlsxWlanAPFrameTypeStatsEntry 4 } wlanAPStatsTotDataPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Data packets observed on this BSSID. " ::= { wlsxWlanAPFrameTypeStatsEntry 5 } wlanAPStatsTotDataBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of Data Bytes observed on this BSSID. " ::= { wlsxWlanAPFrameTypeStatsEntry 6 } -- This table breaks down the BSSID statistics observed into packet size -- buckets. wlsxWlanAPPktSizeStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlsxWlanAPPktSizeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table contains all the per BSSID Packet Count but broken down into different Packet Sizes. " ::= { wlsxWlanAccessPointStatsGroup 5 } wlsxWlanAPPktSizeStatsEntry OBJECT-TYPE SYNTAX WlsxWlanAPPktSizeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Packet Size based packet count entry for a BSSID" INDEX {wlanAPMacAddress, wlanAPRadioNumber, wlanAPBSSID} ::= { wlsxWlanAPPktSizeStatsTable 1 } WlsxWlanAPPktSizeStatsEntry ::= SEQUENCE { wlanAPStatsPkts63Bytes Counter32 , wlanAPStatsPkts64To127 Counter32 , wlanAPStatsPkts128To255 Counter32 , wlanAPStatsPkts256To511 Counter32 , wlanAPStatsPkts512To1023 Counter32 , wlanAPStatsPkts1024To1518 Counter32 } wlanAPStatsPkts63Bytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets that were less than 64 bytes long. " ::= { wlsxWlanAPPktSizeStatsEntry 1 } wlanAPStatsPkts64To127 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets that were between 64 and 127 bytes long. " ::= { wlsxWlanAPPktSizeStatsEntry 2 } wlanAPStatsPkts128To255 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets that were between 128 and 255 bytes long. " ::= { wlsxWlanAPPktSizeStatsEntry 3 } wlanAPStatsPkts256To511 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets that were between 256 and 511 bytes long. " ::= { wlsxWlanAPPktSizeStatsEntry 4 } wlanAPStatsPkts512To1023 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets that were between 512 and 1023 bytes long. " ::= { wlsxWlanAPPktSizeStatsEntry 5 } wlanAPStatsPkts1024To1518 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total number of packets that were between 1024 and 1518 bytes long. " ::= { wlsxWlanAPPktSizeStatsEntry 6 } -- AP Chan Stats table wlsxWlanAPChStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanAPChStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists the Channel statistics of all the Access Points connected to the controller. " ::= { wlsxWlanAccessPointStatsGroup 6 } wlsxWlanAPChStatsEntry OBJECT-TYPE SYNTAX WlanAPChStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access Point Channel Stats entry" INDEX {wlanAPMacAddress, wlanAPRadioNumber} ::= { wlsxWlanAPChStatsTable 1 } WlanAPChStatsEntry ::= SEQUENCE { wlanAPChannelNumber INTEGER, wlanAPChNumStations Integer32, wlanAPChTotPkts Counter32, wlanAPChTotBytes Counter32, wlanAPChTotRetryPkts Counter32, wlanAPChTotFragmentedPkts Counter32, wlanAPChTotPhyErrPkts Counter32, wlanAPChTotMacErrPkts Counter32, wlanAPChNoise Integer32, wlanAPChCoverageIndex Integer32, wlanAPChInterferenceIndex Integer32, wlanAPChFrameRetryRate Integer32, wlanAPChFrameLowSpeedRate Integer32, wlanAPChFrameNonUnicastRate Integer32, wlanAPChFrameFragmentationRate Integer32, wlanAPChFrameBandwidthRate Integer32, wlanAPChFrameRetryErrorRate Integer32, wlanAPChBusyRate Integer32, wlanAPChNumAPs Integer32, wlanAPChFrameReceiveErrorRate Integer32, wlanAPChTransmittedFragmentCount Counter32, wlanAPChMulticastTransmittedFrameCount Counter32, wlanAPChFailedCount Counter32, wlanAPChRetryCount Counter32, wlanAPChMultipleRetryCount Counter32, wlanAPChFrameDuplicateCount Counter32, wlanAPChRTSSuccessCount Counter32, wlanAPChRTSFailureCount Counter32, wlanAPChACKFailureCount Counter32, wlanAPChReceivedFragmentCount Counter32, wlanAPChMulticastReceivedFrameCount Counter32, wlanAPChFCSErrorCount Counter32, wlanAPChTransmittedFrameCount Counter32, wlanAPChWEPUndecryptableCount Counter32, wlanAPChRxUtilization INTEGER, wlanAPChTxUtilization INTEGER, wlanAPChUtilization INTEGER } wlanAPChannelNumber OBJECT-TYPE SYNTAX INTEGER(1..165) MAX-ACCESS read-only STATUS current DESCRIPTION " The channel the AP is currently using. " ::= { wlsxWlanAPChStatsEntry 1 } wlanAPChNumStations OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of stations using this channel. " ::= { wlsxWlanAPChStatsEntry 2 } wlanAPChTotPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total packets observed on this channel. " ::= { wlsxWlanAPChStatsEntry 3 } wlanAPChTotBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total Bytes observed on this channel. " ::= { wlsxWlanAPChStatsEntry 4 } wlanAPChTotRetryPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total Retry Packets observed on this channel. " ::= { wlsxWlanAPChStatsEntry 5 } wlanAPChTotFragmentedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total Fragmented Packets observed on this channel. " ::= { wlsxWlanAPChStatsEntry 6 } wlanAPChTotPhyErrPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total Physical Error Packets observed on this channel. " ::= { wlsxWlanAPChStatsEntry 7 } wlanAPChTotMacErrPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total Mac errors packets observed on this channel. " ::= { wlsxWlanAPChStatsEntry 8 } wlanAPChNoise OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the noise observed on this channel. " ::= { wlsxWlanAPChStatsEntry 9 } wlanAPChCoverageIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the coverage provided by the AP on this channel. " ::= { wlsxWlanAPChStatsEntry 10 } wlanAPChInterferenceIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the interference observed on this channel. " ::= { wlsxWlanAPChStatsEntry 11 } wlanAPChFrameRetryRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of retry packets as a percentage of the total packets transmitted and received on this channel. " ::= { wlsxWlanAPChStatsEntry 12 } wlanAPChFrameLowSpeedRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of low data rate (<= 18Mbps for A/G bands and <=2Mbps for B band) packets as a percentage of the total packets transmitted and received on this channel " ::= { wlsxWlanAPChStatsEntry 13 } wlanAPChFrameNonUnicastRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of broadcast and multicast packets as a percentage of the total packets transmitted on this channel. " ::= { wlsxWlanAPChStatsEntry 14 } wlanAPChFrameFragmentationRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of fragments as a percentage of the total packets transmitted on this channel " ::= { wlsxWlanAPChStatsEntry 15 } wlanAPChFrameBandwidthRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The bandwidth of this channel in Kbps. " ::= { wlsxWlanAPChStatsEntry 16 } wlanAPChFrameRetryErrorRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION " The number of error packets as a percentage of the total packets received on this channel. " ::= { wlsxWlanAPChStatsEntry 17 } wlanAPChBusyRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the busy this channel is. " ::= { wlsxWlanAPChStatsEntry 18 } wlanAPChNumAPs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Access Points observed on this channel. " ::= { wlsxWlanAPChStatsEntry 19 } wlanAPChFrameReceiveErrorRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of error packets as a percentage of the total packets received on this channel. " ::= { wlsxWlanAPChStatsEntry 20 } wlanAPChTransmittedFragmentCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall be incremented for an acknowledged MPDU with an individual address in the address 1 field or an MPDU with a multicast address in the address 1 field of type Data or Management. " ::= { wlsxWlanAPChStatsEntry 21 } wlanAPChMulticastTransmittedFrameCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment only when the multicast bit is set in the destination MAC address of a successfully transmitted MSDU. When operating as a STA in an ESS, where these frames are directed to the AP, this implies having received an acknowledgment to all associated MPDUs. " ::= { wlsxWlanAPChStatsEntry 22 } wlanAPChFailedCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment when an MSDU is not transmitted successfully due to the number of transmit attempts exceeding either the dot11ShortRetryLimit or dot11LongRetryLimit. " ::= { wlsxWlanAPChStatsEntry 23 } wlanAPChRetryCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment when an MSDU is successfully transmitted after one or more retransmissions. " ::= { wlsxWlanAPChStatsEntry 24 } wlanAPChMultipleRetryCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment when an MSDU is successfully transmitted after more than one retransmission. " ::= { wlsxWlanAPChStatsEntry 25 } wlanAPChFrameDuplicateCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment when a frame is received that the Sequence Control field indicates is a duplicate. " ::= { wlsxWlanAPChStatsEntry 26 } wlanAPChRTSSuccessCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment when a CTS is received in response to an RTS. " ::= { wlsxWlanAPChStatsEntry 27 } wlanAPChRTSFailureCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment when a CTS is not received in response to an RTS. " ::= { wlsxWlanAPChStatsEntry 28 } wlanAPChACKFailureCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment when an ACK is not received when expected. " ::= { wlsxWlanAPChStatsEntry 29 } wlanAPChReceivedFragmentCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall be incremented for each successfully received MPDU of type Data or Management. " ::= { wlsxWlanAPChStatsEntry 30 } wlanAPChMulticastReceivedFrameCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment when a MSDU is received with the multicast bit set in the destination MAC address. " ::= { wlsxWlanAPChStatsEntry 31 } wlanAPChFCSErrorCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment when an FCS error is detected in a received MPDU. " ::= { wlsxWlanAPChStatsEntry 32 } wlanAPChTransmittedFrameCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment for each successfully transmitted MSDU. " ::= { wlsxWlanAPChStatsEntry 33 } wlanAPChWEPUndecryptableCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This counter shall increment when a frame is received with the Protected Frame subfield of the Frame Control field set to one and the WEPOn value for the key mapped to the transmitter's MAC address indicates that the frame should not have been encrypted or that frame is discarded due to the receiving STA not implementing the privacy option. " ::= { wlsxWlanAPChStatsEntry 34 } wlanAPChRxUtilization OBJECT-TYPE SYNTAX INTEGER(0..100) MAX-ACCESS read-only STATUS current DESCRIPTION " This is the percentage of time spent by the radio in receiving packets. " ::= { wlsxWlanAPChStatsEntry 35 } wlanAPChTxUtilization OBJECT-TYPE SYNTAX INTEGER(0..100) MAX-ACCESS read-only STATUS current DESCRIPTION " This is the percentage of time spent by the radio in transmitting packets. " ::= { wlsxWlanAPChStatsEntry 36 } wlanAPChUtilization OBJECT-TYPE SYNTAX INTEGER(0..100) MAX-ACCESS read-only STATUS current DESCRIPTION " This is the percentage of time the channel is busy. " ::= { wlsxWlanAPChStatsEntry 37 } -- AP Wired Stats table wlsxWlanAPWiredStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanAPWiredStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists the Wired statistics of all the Access Points connected to the controller. " ::= { wlsxWlanAccessPointStatsGroup 7 } wlsxWlanAPWiredStatsEntry OBJECT-TYPE SYNTAX WlanAPWiredStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access Point Wired Stats entry" INDEX {wlanAPMacAddress} ::= { wlsxWlanAPWiredStatsTable 1 } WlanAPWiredStatsEntry ::= SEQUENCE { wlanAPWiredRxPkts Counter32, wlanAPWiredRxDroppedPkts Counter32, wlanAPWiredRxBytes Counter32, wlanAPWiredTxBytes Counter32, wlanAPWiredRxRate Gauge32, wlanAPWiredTxRate Gauge32 } wlanAPWiredRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total packets received from the AP wired side. " ::= { wlsxWlanAPWiredStatsEntry 1 } wlanAPWiredRxDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total dropped packets received from the AP wired side. " ::= { wlsxWlanAPWiredStatsEntry 2 } wlanAPWiredRxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total bytes of correct packets received from the AP wired side. " ::= { wlsxWlanAPWiredStatsEntry 3 } wlanAPWiredTxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total bytes transmitted from the AP wired side. " ::= { wlsxWlanAPWiredStatsEntry 4 } wlanAPWiredRxRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the data rate (kbyte/s) received from AP wired side in sampling interval. " ::= { wlsxWlanAPWiredStatsEntry 5 } wlanAPWiredTxRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the data rate (kbyte/s) transmitted from AP wired side in sampling interval. " ::= { wlsxWlanAPWiredStatsEntry 6 } -- AP ESSID Stats table wlsxWlanAPESSIDStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanAPESSIDStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists the ESSID statistics of all the Access Points connected to the controller. " ::= { wlsxWlanAccessPointStatsGroup 8 } wlsxWlanAPESSIDStatsEntry OBJECT-TYPE SYNTAX WlanAPESSIDStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access Point ESSID Stats entry" INDEX {wlanAPMacAddress, wlanESSID} ::= { wlsxWlanAPESSIDStatsTable 1 } WlanAPESSIDStatsEntry ::= SEQUENCE { wlanAPESSIDWirelessRxBytes Counter32, wlanAPESSIDWirelessTxBytes Counter32, wlanAPESSIDWiredRxBytes Counter32, wlanAPESSIDWiredTxBytes Counter32 } wlanAPESSIDWirelessRxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total bytes of correct packets received from the AP ESSID wireless side. " ::= { wlsxWlanAPESSIDStatsEntry 1 } wlanAPESSIDWirelessTxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total bytes transmitted from the AP ESSID wireless side. " ::= { wlsxWlanAPESSIDStatsEntry 2 } wlanAPESSIDWiredRxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total bytes of correct packets received from the AP ESSID wired side. " ::= { wlsxWlanAPESSIDStatsEntry 3 } wlanAPESSIDWiredTxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total bytes transmitted from the AP ESSID wired side. " ::= { wlsxWlanAPESSIDStatsEntry 4 } -- AP Radio Stats table wlsxWlanAPRadioStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanAPRadioStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists the Radio statistics of all the Access Points connected to the controller. " ::= { wlsxWlanAccessPointStatsGroup 9 } wlsxWlanAPRadioStatsEntry OBJECT-TYPE SYNTAX WlanAPRadioStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access Point Radio Stats entry" INDEX {wlanAPMacAddress, wlanAPRadioNumber} ::= { wlsxWlanAPRadioStatsTable 1 } WlanAPRadioStatsEntry ::= SEQUENCE { wlanAPRadioRxPkts Counter32, wlanAPRadioRxBytes Counter32, wlanAPRadioTxPkts Counter32, wlanAPRadioTxBytes Counter32, wlanAPRadioTxDroppedPkts Counter32, wlanAPRadioTxErrorPkts Counter32, wlanAPRadioRxRate Gauge32, wlanAPRadioTxRate Gauge32, wlanApRadioAssocReqCount Counter32, wlanApRadioAssocReqSuccCount Counter32, wlanApRadioReAssocReqCount Counter32, wlanApRadioReAssocReqSuccCount Counter32, wlanAPRadioStationDuration Integer32, wlanAPRadioAssocSuccPercent Gauge32, wlanAPRadioTxDataBytes Counter32 } wlanAPRadioRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total packets transmitted from the AP radio wireless side. " ::= { wlsxWlanAPRadioStatsEntry 1 } wlanAPRadioRxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total correct bytes received from the AP radio wireless side. " ::= { wlsxWlanAPRadioStatsEntry 2 } wlanAPRadioTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total packets transmitted from the AP radio wireless side. " ::= { wlsxWlanAPRadioStatsEntry 3 } wlanAPRadioTxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total bytes transmitted from the AP radio wireless side. " ::= { wlsxWlanAPRadioStatsEntry 4 } wlanAPRadioTxDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the dropped packets transmitted from the AP radio wireless side. " ::= { wlsxWlanAPRadioStatsEntry 5 } wlanAPRadioTxErrorPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the error packets transmitted from the AP radio wireless side. " ::= { wlsxWlanAPRadioStatsEntry 6 } wlanAPRadioRxRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the data rate (kbyte/s) received from AP radio wireless side in sampling interval. " ::= { wlsxWlanAPRadioStatsEntry 7 } wlanAPRadioTxRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the data rate (kbyte/s) transmitted from AP radio wireless side in sampling interval. " ::= { wlsxWlanAPRadioStatsEntry 8 } wlanApRadioAssocReqCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates the times of associate request on this radio." ::= { wlsxWlanAPRadioStatsEntry 9 } wlanApRadioAssocReqSuccCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates the times of successful associate request on this radio." ::= { wlsxWlanAPRadioStatsEntry 10 } wlanApRadioReAssocReqCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates the times of re-associate request on this radio." ::= { wlsxWlanAPRadioStatsEntry 11 } wlanApRadioReAssocReqSuccCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates the times of successful re-associate request on this radio. " ::= { wlsxWlanAPRadioStatsEntry 12 } wlanAPRadioStationDuration OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total occupied duration, which is the total duration of user connecting. " ::= { wlsxWlanAPRadioStatsEntry 13 } wlanAPRadioAssocSuccPercent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION " The Association Success Percent. " ::= { wlsxWlanAPRadioStatsEntry 14 } wlanAPRadioTxDataBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total data bytes transmitted from the AP radio wireless side. " ::= { wlsxWlanAPRadioStatsEntry 15 } -- wlsxWlanStationStatsGroup contains all the statistics observed by different -- Air Monitors attached to this controller. -- Station Statistics are observed by the Air Monitor for that -- specific Station. -- Station Statistics are grouped into Generic, -- Rate, Destination Address and Frame Type Stats. -- Station Statistics Group contains all the statistics related to -- a Station. -- wlsxWlanStationStatsTable will contain all the aggregate statistics collected -- for a Station wlsxWlanStationStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanStationStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists statistics of all the wireless stations associated with an AP connected to this controller. " ::= { wlsxWlanStationStatsGroup 1} wlsxWlanStationStatsEntry OBJECT-TYPE SYNTAX WlanStationStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Station Stats Entry" INDEX {wlanStaPhyAddress} ::= { wlsxWlanStationStatsTable 1 } WlanStationStatsEntry ::= SEQUENCE { wlanStaChannelNum Unsigned32, wlanStaTxPkts Counter32, wlanStaTxBytes Counter32, wlanStaRxPkts Counter32, wlanStaRxBytes Counter32, wlanStaTxBCastPkts Counter32, wlanStaRxBCastBytes Counter32, wlanStaTxMCastPkts Counter32, wlanStaRxMCastBytes Counter32, wlanStaDataPkts Counter32, wlanStaCtrlPkts Counter32, wlanStaNumAssocRequests Counter32, wlanStaNumAuthRequests Counter32, wlanStaTxDeauthentications Counter32, wlanStaRxDeauthentications Counter32, wlanStaFrameRetryRate Integer32, wlanStaFrameLowSpeedRate Integer32, wlanStaFrameNonUnicastRate Integer32, wlanStaFrameFragmentationRate Integer32, wlanStaFrameBandwidthRate Integer32, wlanStaFrameRetryErrorRate Integer32, wlanStaFrameReceiveErrorRate Integer32, wlanStaTxBCastBytes Counter32, wlanStaTxMCastBytes Counter32, wlanStaTxBytes64 Counter64, wlanStaRxBytes64 Counter64 } wlanStaChannelNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " The channel the station is currently using. " ::= { wlsxWlanStationStatsEntry 1 } wlanStaTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of packets transmitted by this station. " ::= { wlsxWlanStationStatsEntry 2 } wlanStaTxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of bytes transmitted by this station. " ::= { wlsxWlanStationStatsEntry 3 } wlanStaRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of packets received by this station. " ::= { wlsxWlanStationStatsEntry 4 } wlanStaRxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of bytes received by this station. " ::= { wlsxWlanStationStatsEntry 5 } wlanStaTxBCastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of broadcast packets transmitted by this station. " ::= { wlsxWlanStationStatsEntry 6 } wlanStaRxBCastBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION " The number of broadcast bytes transmitted by this station. " ::= { wlsxWlanStationStatsEntry 7 } wlanStaTxMCastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of multicast packets transmitted by this station. " ::= { wlsxWlanStationStatsEntry 8 } wlanStaRxMCastBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION " The number of multicast bytes transmitted by this station. " ::= { wlsxWlanStationStatsEntry 9 } wlanStaDataPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of Data packets transmitted by this station. " ::= { wlsxWlanStationStatsEntry 10 } wlanStaCtrlPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of Control packets transmitted by this station. " ::= { wlsxWlanStationStatsEntry 11 } wlanStaNumAssocRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of Association requests transmitted by this station. " ::= { wlsxWlanStationStatsEntry 12 } wlanStaNumAuthRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of Authentication requests transmitted by this station. " ::= { wlsxWlanStationStatsEntry 13 } wlanStaTxDeauthentications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of Deauthentication frames transmitted by this station. " ::= { wlsxWlanStationStatsEntry 14 } wlanStaRxDeauthentications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of Deauthentication frames received by this station. " ::= { wlsxWlanStationStatsEntry 15 } wlanStaFrameRetryRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of retry packets as a percentage of the total packets transmitted and received by this station. " ::= { wlsxWlanStationStatsEntry 16 } wlanStaFrameLowSpeedRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of low data rate (<= 18Mbps for A/G bands and <=2Mbps for B band) packets as a percentage of the total packets transmitted and received by this station. " ::= { wlsxWlanStationStatsEntry 17 } wlanStaFrameNonUnicastRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of broadcast and multicast packets as a percentage of the total packets transmitted by this station. " ::= { wlsxWlanStationStatsEntry 18 } wlanStaFrameFragmentationRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of fragments as a percentage of the total packets transmitted by this station. " ::= { wlsxWlanStationStatsEntry 19 } wlanStaFrameBandwidthRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The bandwidth of this station in Kbps. " ::= { wlsxWlanStationStatsEntry 20 } wlanStaFrameRetryErrorRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION " The number of error packets as a percentage of the total packets received by this station. " ::= { wlsxWlanStationStatsEntry 21 } wlanStaFrameReceiveErrorRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of error packets as a percentage of the total packets received by this station. " ::= { wlsxWlanStationStatsEntry 22 } wlanStaTxBCastBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of broadcast bytes transmitted by this station. " ::= { wlsxWlanStationStatsEntry 23 } wlanStaTxMCastBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of multicast bytes transmitted by this station. " ::= { wlsxWlanStationStatsEntry 24 } wlanStaTxBytes64 OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of bytes transmitted by this station, 64-bit value " ::= { wlsxWlanStationStatsEntry 25 } wlanStaRxBytes64 OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of bytes received by this station, 64-bit value " ::= { wlsxWlanStationStatsEntry 26 } -- This table breaks down the Station statistics into different -- rate categories. wlsxWlanStaRateStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlsxWlanStaRateStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table contains all the Packet and Byte Counts for a station represented in terms of rate categories. " ::= { wlsxWlanStationStatsGroup 2} wlsxWlanStaRateStatsEntry OBJECT-TYPE SYNTAX WlsxWlanStaRateStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Data rate based packet and byte count entry for a station" INDEX {wlanStaPhyAddress} ::= { wlsxWlanStaRateStatsTable 1 } WlsxWlanStaRateStatsEntry ::= SEQUENCE { wlanStaTxPktsAt1Mbps Counter32, wlanStaTxBytesAt1Mbps Counter32, wlanStaTxPktsAt2Mbps Counter32, wlanStaTxBytesAt2Mbps Counter32, wlanStaTxPktsAt5Mbps Counter32, wlanStaTxBytesAt5Mbps Counter32, wlanStaTxPktsAt11Mbps Counter32, wlanStaTxBytesAt11Mbps Counter32, wlanStaTxPktsAt6Mbps Counter32, wlanStaTxBytesAt6Mbps Counter32, wlanStaTxPktsAt12Mbps Counter32, wlanStaTxBytesAt12Mbps Counter32, wlanStaTxPktsAt18Mbps Counter32, wlanStaTxBytesAt18Mbps Counter32, wlanStaTxPktsAt24Mbps Counter32, wlanStaTxBytesAt24Mbps Counter32, wlanStaTxPktsAt36Mbps Counter32, wlanStaTxBytesAt36Mbps Counter32, wlanStaTxPktsAt48Mbps Counter32, wlanStaTxBytesAt48Mbps Counter32, wlanStaTxPktsAt54Mbps Counter32, wlanStaTxBytesAt54Mbps Counter32, wlanStaRxPktsAt1Mbps Counter32, wlanStaRxBytesAt1Mbps Counter32, wlanStaRxPktsAt2Mbps Counter32, wlanStaRxBytesAt2Mbps Counter32, wlanStaRxPktsAt5Mbps Counter32, wlanStaRxBytesAt5Mbps Counter32, wlanStaRxPktsAt11Mbps Counter32, wlanStaRxBytesAt11Mbps Counter32, wlanStaRxPktsAt6Mbps Counter32, wlanStaRxBytesAt6Mbps Counter32, wlanStaRxPktsAt12Mbps Counter32, wlanStaRxBytesAt12Mbps Counter32, wlanStaRxPktsAt18Mbps Counter32, wlanStaRxBytesAt18Mbps Counter32, wlanStaRxPktsAt24Mbps Counter32, wlanStaRxBytesAt24Mbps Counter32, wlanStaRxPktsAt36Mbps Counter32, wlanStaRxBytesAt36Mbps Counter32, wlanStaRxPktsAt48Mbps Counter32, wlanStaRxBytesAt48Mbps Counter32, wlanStaRxPktsAt54Mbps Counter32, wlanStaRxBytesAt54Mbps Counter32, wlanStaTxPktsAt9Mbps Counter32, wlanStaTxBytesAt9Mbps Counter32, wlanStaRxPktsAt9Mbps Counter32, wlanStaRxBytesAt9Mbps Counter32 } wlanStaTxPktsAt1Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 1Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 1 } wlanStaTxBytesAt1Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 1Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 2 } wlanStaTxPktsAt2Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 2Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 3 } wlanStaTxBytesAt2Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 2Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 4 } wlanStaTxPktsAt5Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 5Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 5 } wlanStaTxBytesAt5Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 5Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 6 } wlanStaTxPktsAt11Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 11Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 7 } wlanStaTxBytesAt11Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 11Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 8 } wlanStaTxPktsAt6Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 6Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 9 } wlanStaTxBytesAt6Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 6Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 10 } wlanStaTxPktsAt12Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 12Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 11 } wlanStaTxBytesAt12Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 12Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 12 } wlanStaTxPktsAt18Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 18Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 13 } wlanStaTxBytesAt18Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 18Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 14 } wlanStaTxPktsAt24Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 24Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 15 } wlanStaTxBytesAt24Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 24Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 16 } wlanStaTxPktsAt36Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 36Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 17 } wlanStaTxBytesAt36Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 36Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 18 } wlanStaTxPktsAt48Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 48Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 19 } wlanStaTxBytesAt48Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 48Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 20 } wlanStaTxPktsAt54Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 54Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 21 } wlanStaTxBytesAt54Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 54Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 22 } wlanStaRxPktsAt1Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 1Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 23 } wlanStaRxBytesAt1Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 1Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 24 } wlanStaRxPktsAt2Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 2Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 25 } wlanStaRxBytesAt2Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 2Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 26 } wlanStaRxPktsAt5Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 5Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 27 } wlanStaRxBytesAt5Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 5Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 28 } wlanStaRxPktsAt11Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 11Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 29 } wlanStaRxBytesAt11Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 11Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 30 } wlanStaRxPktsAt6Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 6Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 31 } wlanStaRxBytesAt6Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 6Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 32 } wlanStaRxPktsAt12Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 12Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 33 } wlanStaRxBytesAt12Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 12Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 34 } wlanStaRxPktsAt18Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 18Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 35 } wlanStaRxBytesAt18Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 18Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 36 } wlanStaRxPktsAt24Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 24Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 37 } wlanStaRxBytesAt24Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 24Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 38 } wlanStaRxPktsAt36Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 36Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 39 } wlanStaRxBytesAt36Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 36Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 40 } wlanStaRxPktsAt48Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 48Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 41 } wlanStaRxBytesAt48Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 48Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 42 } wlanStaRxPktsAt54Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 54Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 43 } wlanStaRxBytesAt54Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 54Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 44 } wlanStaTxPktsAt9Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Transmitted by the station at 9Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 45 } wlanStaTxBytesAt9Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Transmitted by the station at 9Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 46 } wlanStaRxPktsAt9Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Packets Received by the station at 9Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 47 } wlanStaRxBytesAt9Mbps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Octets Received by the station at 9Mbps rate. " ::= { wlsxWlanStaRateStatsEntry 48 } -- This table breaks down the Station statistics based on the -- Destination Address Types. wlsxWlanStaDATypeStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlsxWlanStaDATypeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table contains all the Packet and Byte Counts for a station but but broken down in terms of Destination Address Type. " ::= { wlsxWlanStationStatsGroup 3} wlsxWlanStaDATypeStatsEntry OBJECT-TYPE SYNTAX WlsxWlanStaDATypeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Destination Address based packet and byte count entry for a station " INDEX {wlanStaPhyAddress} ::= { wlsxWlanStaDATypeStatsTable 1 } WlsxWlanStaDATypeStatsEntry ::= SEQUENCE { wlanStaTxDABroadcastPkts Counter32 , wlanStaTxDABroadcastBytes Counter32 , wlanStaTxDAMulticastPkts Counter32 , wlanStaTxDAMulticastBytes Counter32 , wlanStaTxDAUnicastPkts Counter32 , wlanStaTxDAUnicastBytes Counter32 } wlanStaTxDABroadcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Broadcast packets transmitted by this Station. " ::= { wlsxWlanStaDATypeStatsEntry 1 } wlanStaTxDABroadcastBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Broadcast Bytes transmitted by this Station. " ::= { wlsxWlanStaDATypeStatsEntry 2 } wlanStaTxDAMulticastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Multicast packets transmitted by this station. " ::= { wlsxWlanStaDATypeStatsEntry 3 } wlanStaTxDAMulticastBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of Multicast Bytes transmitted by this station. " ::= { wlsxWlanStaDATypeStatsEntry 4 } wlanStaTxDAUnicastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total of Unicast packets transmitted by this station. " ::= { wlsxWlanStaDATypeStatsEntry 5 } wlanStaTxDAUnicastBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the total of Unicast Bytes transmitted by this station. " ::= { wlsxWlanStaDATypeStatsEntry 6 } -- This table breaks down the Station statistics based on the -- the Type of the Packet. wlsxWlanStaFrameTypeStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlsxWlanStaFrameTypeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table contains all the Packet and Byte Counts for stations but broken down into different Frame Types. " ::= { wlsxWlanStationStatsGroup 4} wlsxWlanStaFrameTypeStatsEntry OBJECT-TYPE SYNTAX WlsxWlanStaFrameTypeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Frame Type based packet and byte count entry for a station" INDEX {wlanStaPhyAddress} ::= { wlsxWlanStaFrameTypeStatsTable 1 } WlsxWlanStaFrameTypeStatsEntry ::= SEQUENCE { wlanStaTxMgmtPkts Counter32 , wlanStaTxMgmtBytes Counter32 , wlanStaTxCtrlPkts Counter32 , wlanStaTxCtrlBytes Counter32 , wlanStaTxDataPkts Counter32 , wlanStaTxDataBytes Counter32 , wlanStaRxMgmtPkts Counter32 , wlanStaRxMgmtBytes Counter32 , wlanStaRxCtrlPkts Counter32 , wlanStaRxCtrlBytes Counter32 , wlanStaRxDataPkts Counter32 , wlanStaRxDataBytes Counter32 } wlanStaTxMgmtPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the Transmitted Management packets from a station. " ::= { wlsxWlanStaFrameTypeStatsEntry 1 } wlanStaTxMgmtBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the Transmitted Management Bytes from a station " ::= { wlsxWlanStaFrameTypeStatsEntry 2 } wlanStaTxCtrlPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the Transmitted Control packets from a station " ::= { wlsxWlanStaFrameTypeStatsEntry 3 } wlanStaTxCtrlBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the Transmitted Control Bytes from a station " ::= { wlsxWlanStaFrameTypeStatsEntry 4 } wlanStaTxDataPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the Transmitted Data packets from a station " ::= { wlsxWlanStaFrameTypeStatsEntry 5 } wlanStaTxDataBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the Transmitted Data Bytes observed on this channel. " ::= { wlsxWlanStaFrameTypeStatsEntry 6 } wlanStaRxMgmtPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of received Management packets at a station. " ::= { wlsxWlanStaFrameTypeStatsEntry 7 } wlanStaRxMgmtBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of received Management Bytes at a station. " ::= { wlsxWlanStaFrameTypeStatsEntry 8 } wlanStaRxCtrlPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of received Control packets at a station. " ::= { wlsxWlanStaFrameTypeStatsEntry 9 } wlanStaRxCtrlBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of received Control Bytes at a station. " ::= { wlsxWlanStaFrameTypeStatsEntry 10 } wlanStaRxDataPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of received Data packets at a station. " ::= { wlsxWlanStaFrameTypeStatsEntry 11 } wlanStaRxDataBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of received Data Bytes at a station. " ::= { wlsxWlanStaFrameTypeStatsEntry 12 } -- This table breaks down the Station statistics received or transmitted by a -- station into packet size buckets. wlsxWlanStaPktSizeStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlsxWlanStaPktSizeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table contains all the Packet and Byte Counts for stations but broken down into different Packet Sizes. " ::= { wlsxWlanStationStatsGroup 5} wlsxWlanStaPktSizeStatsEntry OBJECT-TYPE SYNTAX WlsxWlanStaPktSizeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Packet Size based packet count entry for a station" INDEX {wlanStaPhyAddress} ::= { wlsxWlanStaPktSizeStatsTable 1 } WlsxWlanStaPktSizeStatsEntry ::= SEQUENCE { wlanStaTxPkts63Bytes Counter32 , wlanStaTxPkts64To127 Counter32 , wlanStaTxPkts128To255 Counter32 , wlanStaTxPkts256To511 Counter32 , wlanStaTxPkts512To1023 Counter32 , wlanStaTxPkts1024To1518 Counter32 , wlanStaRxPkts63Bytes Counter32 , wlanStaRxPkts64To127 Counter32 , wlanStaRxPkts128To255 Counter32 , wlanStaRxPkts256To511 Counter32 , wlanStaRxPkts512To1023 Counter32 , wlanStaRxPkts1024To1518 Counter32 } wlanStaTxPkts63Bytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets transmitted by the station that were less than 64 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 1 } wlanStaTxPkts64To127 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets transmitted by the station that were between 64 and 127 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 2 } wlanStaTxPkts128To255 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets transmitted by the station that were between 128 and 255 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 3 } wlanStaTxPkts256To511 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets transmitted by the station that were between 256 and 511 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 4 } wlanStaTxPkts512To1023 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets transmitted by the station that were between 512 and 1023 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 5 } wlanStaTxPkts1024To1518 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets transmitted by the station that were between 1024 and 1518 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 6 } wlanStaRxPkts63Bytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets Received by the station that were less than 64 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 7 } wlanStaRxPkts64To127 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets Received by the station that were between 64 and 127 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 8 } wlanStaRxPkts128To255 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets Received by the station that were between 128 and 255 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 9 } wlanStaRxPkts256To511 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets Received by the station that were between 256 and 511 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 10 } wlanStaRxPkts512To1023 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets Received by the station that were between 512 and 1023 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 11 } wlanStaRxPkts1024To1518 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the number of packets Received by the station that were between 1024 and 1518 bytes long. " ::= { wlsxWlanStaPktSizeStatsEntry 12 } -- wlsxWlanSwitchStatsGroup contains all statistics related to -- the whole network controlled by the controller. -- wlsxWlanESSIDStatsTable contains all statistics collected -- for an ESSID on the switch wlsxWlanESSIDStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanESSIDStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists statistics of the ESSID controlled by this controller. " ::= { wlsxWlanSwitchStatsGroup 1} wlsxWlanESSIDStatsEntry OBJECT-TYPE SYNTAX WlanESSIDStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "ESSID Stats Entry" INDEX {wlanESSID} ::= { wlsxWlanESSIDStatsTable 1 } WlanESSIDStatsEntry ::= SEQUENCE { wlanESSIDRxPkts Counter32, wlanESSIDRxDroppedPkts Counter32, wlanESSIDRxRetryPkts Counter32, wlanESSIDTxPkts Counter32, wlanESSIDTxDroppedPkts Counter32, wlanESSIDTxRetryPkts Counter32, wlanESSIDTxErrorPkts Counter32, wlanESSIDRxRate Gauge32, wlanESSIDTxRate Gauge32, wlanESSIDWiredRxPkts Counter32, wlanESSIDWiredRxBytes Counter32, wlanESSIDWiredTxBytes Counter32 } wlanESSIDRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of packets on the ESSID uplink channel of wireless side. " ::= { wlsxWlanESSIDStatsEntry 1 } wlanESSIDRxDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of dropped packets on the ESSID uplink channel of wireless side. " ::= { wlsxWlanESSIDStatsEntry 2 } wlanESSIDRxRetryPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of re-transmission packets on the ESSID uplink channel of wireless side. " ::= { wlsxWlanESSIDStatsEntry 3 } wlanESSIDTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of packets on the ESSID downlink channel of wireless side. " ::= { wlsxWlanESSIDStatsEntry 4 } wlanESSIDTxDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of dropped packets on the ESSID downlink channel of wireless side. " ::= { wlsxWlanESSIDStatsEntry 5 } wlanESSIDTxRetryPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of re-transmission packets on the ESSID downlink channel of wireless side. " ::= { wlsxWlanESSIDStatsEntry 6 } wlanESSIDTxErrorPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of error packets on the ESSID downlink channel of wireless side. " ::= { wlsxWlanESSIDStatsEntry 7 } wlanESSIDRxRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION " The data rate received from the ESSID in sampling interval, unit is kbyte/s. " ::= { wlsxWlanESSIDStatsEntry 8 } wlanESSIDTxRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION " The data rate transmitted from the ESSID in sampling interval, unit is kbyte/s. " ::= { wlsxWlanESSIDStatsEntry 9 } wlanESSIDWiredRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of packets on the ESSID uplink channel of wired side. " ::= { wlsxWlanESSIDStatsEntry 10 } wlanESSIDWiredRxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of bytes on the ESSID uplink channel of wireless side. " ::= { wlsxWlanESSIDStatsEntry 11 } wlanESSIDWiredTxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The total number of bytes on the ESSID downlink channel of wireless side. " ::= { wlsxWlanESSIDStatsEntry 12 } -- wlsxWlanEthStatsTable will contain all the statistics collected -- for all ethernet ports wlsxWlanEthStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanEthStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists statistics of all ethernet ports of this controller. " ::= { wlsxWlanSwitchStatsGroup 2} wlsxWlanEthStatsEntry OBJECT-TYPE SYNTAX WlanEthStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ethernet Port Stats Entry" INDEX {ifIndex} ::= { wlsxWlanEthStatsTable 1 } WlanEthStatsEntry ::= SEQUENCE { wlanEthRxRate Gauge32, wlanEthTxRate Gauge32 } wlanEthRxRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION " The data rate received from the ethernet port in sampling interval, unit is kbyte/s. " ::= { wlsxWlanEthStatsEntry 1 } wlanEthTxRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION " The data rate transmitted from the ethernet port in sampling interval, unit is kbyte/s. " ::= { wlsxWlanEthStatsEntry 2 } -- wlsxSSIDConfigGroup contains all configuration related to -- the SSID controlled by the controller. -- wlsxSSIDConfigTable contains the global configuration of the SSID wlsxSSIDConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanSSIDConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists the configuration of the SSID. Note: Currently, this table doesn't return any data. " ::= { wlsxSSIDConfigGroup 1} wlsxSSIDConfigEntry OBJECT-TYPE SYNTAX WlanSSIDConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "AP Configuration Entry" INDEX {wlanAPMacAddress, wlanAPRadioNumber, wlanESSID, wlanESSIDIndex} ::= { wlsxSSIDConfigTable 1 } WlanSSIDConfigEntry ::= SEQUENCE { wlanESSIDIndex Integer32, wlanSSIDConfigHideSSID TruthValue, wlanSSIDConfigNumStaAllowed Unsigned32, wlanSSIDConfigWmmBeDscp Unsigned32, wlanSSIDConfigWmmBkDscp Unsigned32, wlanSSIDConfigWmmViDscp Unsigned32, wlanSSIDConfigWmmVoDscp Unsigned32 } wlanESSIDIndex OBJECT-TYPE SYNTAX Integer32(1..16) MAX-ACCESS not-accessible STATUS current DESCRIPTION " This attribute indicates the index of ESSID. We support up to 16 ESSIDs. " ::= { wlsxSSIDConfigEntry 1 } wlanSSIDConfigHideSSID OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates if SSID is hidden or not. " ::= { wlsxSSIDConfigEntry 2 } wlanSSIDConfigNumStaAllowed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the maximum number of stations that are allowed to access into the network. " ::= { wlsxSSIDConfigEntry 3 } wlanSSIDConfigWmmBeDscp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the QoS priority of best-effort service. " ::= { wlsxSSIDConfigEntry 4 } wlanSSIDConfigWmmBkDscp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the QoS priority of background service. " ::= { wlsxSSIDConfigEntry 5 } wlanSSIDConfigWmmViDscp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the QoS priority of video service. " ::= { wlsxSSIDConfigEntry 6 } wlanSSIDConfigWmmVoDscp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " This attribute indicates the QoS priority of voice service. " ::= { wlsxSSIDConfigEntry 7 } -- wlsxAPConfigGroup contains all configuration related to -- the APs controlled by the controller. -- wlsxAPConfigTable contains the global configuration of the AP wlsxAPConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF WlanAPConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This Table lists the configuration of the Access Point. " ::= { wlsxAPConfigGroup 1} wlsxAPConfigEntry OBJECT-TYPE SYNTAX WlanAPConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "AP Configuration Entry" INDEX {wlanAPMacAddress} ::= { wlsxAPConfigTable 1 } WlanAPConfigEntry ::= SEQUENCE { wlanAPConfigNetmask IpAddress, wlanAPConfigGateway IpAddress } wlanAPConfigNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " The netmask of AP IP Address. " ::= { wlsxAPConfigEntry 1 } wlanAPConfigGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " The gateway of the AP. " ::= { wlsxAPConfigEntry 2 } --Trap Definition wlsxRAPActiveUplink NOTIFICATION-TYPE OBJECTS {wlanAPActiveUplink, wlanAPMacAddress} STATUS current DESCRIPTION "A trap which indicates the RAP Active Uplink" ::= { wlsxRAPTraps 1 } END