We have a pair of 2930M switches with 2930M 4SFP+ (JL083A) modules that we are installing in the back. For some reason neither one will power up. We do have the stacking modules active next to the uplink slots and they work fine. I have reseated the modules several times but never even see a status light blink on them when the switch powers up. Do I need to activate the port they plug into or something?
what SFP + Gbic or DA cable you have installed?The module itself is still nothing
I have twinaxial cables going to a couple of servers. The servers do recognize their 10G ports. I also have a 10G transceiver in one of the slots but it isn't connected to anything yet. Even with all the slots empty I do not see any lights when the switch boots up.
Are u using Aruba/HPE SFP's ? or 3rd party vendor , if 3rd party vendor,Please read here:
I'm using HPE Aruba cables and transceiver modules. PN: J9283D and J9150D respectively. It's all new equipment as well.
Might be switch firmware? what version installed on your 2930M?
I'll upgrade the firmware and see if that helps. I'm currently on WC.16.07.0002 which is older. Thanks for working with me on this. I'll be back on-site in a few days and will run the upgrade. I'll post the results.
should work when installed, no config needed.
do you see the interfaces under show interface brief? they are numbered with an 1/A1 for stack member 1, or interface A1 if no stacking is enabled.
They do not show up under the interfaces. Reading the manual it looks like they should have amber lights during boot and for any unplugged ports but I get nothing at all ever. It's as if nothing is plugged into the module slot at all. They are seating properly and I have re-seated them a few times just to be sure. One thought I had was power. Each swich only has one of power supply in it but there is an empty slot for a redundant power supply as well. Even though these are not POE switches I do have the stacking modules installed and working which may necessitate that I use a second PSU??? Thoughts?
Maybe stupid: But last time i installed them, i really need to push them quit hard to get the last bit in, did you use enough force to completely click them in?
I thought the same thing and pressed them in as far as they would go then really cranked down on the captive screws. Nothing. I'll keep trying. I'm hoping the firmware update might yeild some results. I'm also considering doing a full reset on the switches to see if it can then see the modules when it boots back up.
This may be a silly question, but are you plugged into the Flex port? It is located to the right of the Stacking port blank (when viewed from the rear)? There is also a slot for an extra power supply as well.
They are in the correct slots. All three slots are actually different from each other. We're using the stacking slot already and one if the two power supply slots.
The uplink module and the transceivers are listed as supported on the HPE QuickSpecs site. The only module I have had issues with was the Smart Rate cards, they did require OS version WC 16.04.XX.
That was the first OS version to support the JL083A uplink module
You have indicated you are already at WC 16.07, so that should not be the issue. I have not found any Technical notices that indicate failures. There is another community article JL083A module not found in hp Aruba 2930M switch . The Solution was solved by a switch OS update.
Software is available at the Aruba Support Portal and at the HPE Support site.
I'll try the update and post back.
Fabian called it. They were not installed fully. I even had the screws tightened down but pushing really hard moved them another millimeter or so which immediately lit up the ports. Hopefully my idiocy will server to help others in the future. Thanks everyone for your responses. It's working perfectly now.
At Aruba, we believe that the most dynamic customer experiences happen at the Edge. Our mission is to deliver innovative solutions that harness data at the Edge to drive powerful business outcomes.
© Copyright 2021 Hewlett Packard Enterprise Development LPAll Rights Reserved.