Direct question ... I am not aware of these devices ...
I have found at home an Aruba Ap 224 ... and I want it to work,
-It is already prescribed by Telnet
-I have done everything I have found on the web
and there is no way that I can see a wifi or that it works as an AP ... the device is with the green flashing light and the Ehrt0 is working, I see it on the network as (192.168.2.110), but it does not open web neither with 4343 nor with anything ... I managed to connect to it by telnet ... (I reset it following steps on youtube) and continue like this
Summary .. Intermittent power light and Lan0 light working, I see a network but I do not see the web interface to enter .... no wifi or anything ... just Telnet saying this in booting :
APBoot 1.4.0.6 (build 38177)
Built: 2013-04-25 at 22:52:20
Model: AP-22x
CPU0: P1020E, Version: 1.1, (0x80ec0011)
Core: E500, Version: 5.1, (0x80212051)
Clock:
CPU0: 800 MHz
CPU1: 800 MHz
CCB: 400 MHz
DDR: 333.333 MHz (666.667 MT/s data rate) (Asynchronous)
LBC: 25 MHz
L1: D-cache 32KB enabled
I-cache 32KB enabled
I2C: ready
DRAM: Configuring DDR for 666.667 MT/s data rate
DDR: 512 MB (DDR3, 32-bit, CL=5, ECC off)
POST1: memory passed
Flash: 32 MB
L2: 256 KB enabled
Power: DC
PCIe1: RC, link up, x1
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 14e4 43a2 00002 03 80000004 00000000 80200004 00000000
PCIe2: RC, link up, x1
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 14e4 43a1 00002 03 a0000004 00000000 a0200004 00000000
Net: eth0, eth1
Radio: bcm43460#0, bcm43460#1
Hit <Enter> to stop autoboot: 0
Checking image @ 0xee000000
Invalid image format version: 0xffffffff
Checking image @ 0xeee00000
Copying image from 0xeee00000
Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
Aruba Networks
ArubaOS Version 6.3.1.0 (build 39345 / label #39345)
Built by p4build@tortuga on 2013-08-08 at 16:30:24 PDT (gcc version 4.5.1)
Memory: 510348k/524288k available (8348k kernel code, 13940k reserved, 540k data, 352k bss, 5008k init)
Processor 1 found.
Brought up 2 CPUs
PCI: Probing PCI hardware
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0001:02:00.0: PCI bridge to [bus 03-ff]
pci 0000:00:00.0: enabling device (0106 -> 0107)
pci 0001:02:00.0: enabling device (0106 -> 0107)
ee000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
/proc/gfar_eth0_stats created
/proc/gfar_eth1_stats created
Enabling watchdog on CPU 1
Enabling watchdog on CPU 0
Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
Starting Kernel DES KAT ...Completed Kernel DES KAT
Starting Kernel AES KAT ...Completed Kernel AES KAT
Domain Name: arubanetworks.com
No panic info available
Ethernet port 1 mode: active-standby
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): bond0: link is not ready
bonding: bond0: enslaving eth0 as a backup interface with a down link.
ADDRCONF(NETDEV_UP): eth1: link is not ready
bonding: bond0: enslaving eth1 as a backup interface with a down link.
AP xml model 66, num_radios 2 (jiffies 3267)
init_asap_mod: installation:0
radio 0: band 1 ant 0 max_ssid 16
radio 1: band 0 ant 0 max_ssid 16
ethernet_device_event: dev eth0 is up
ASAP Slowpath initialized
Starting watchdog process...
Getting an IP address...
PHY: eth0 (mdio@ffe24000:00) - Link is Up - 1000/Full
bonding: bond0: link status definitely up for interface eth0.
bonding: bond0: making interface eth0 the new active one.
bonding: bond0: first active interface up!
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
192.168.2.110 255.255.255.0 192.168.2.1
Running ADP...
------------------------------
Hector Hernandez
------------------------------