Wireless Access

 View Only

  • 1.  AurubaOS 8.6 HA configuration not working

    Posted Apr 23, 2022 06:34 PM
    Hi

    I've added on HA Groups new  group named "HA-group", added both controllers on it and configured HA Member to point "HA-group"

    VRRP is working fine, have MAster and Backup MC's
    both WLC's were installed as Standalone mode initially
    -----------

    From wlc-1
    (x-aruba-wlc-1) *[mynode] #show switches

    All Switches
    ------------
    IP Address IPv6 Address Name Location Type Model Version Status Configuration State Config Sync Time (sec) Config ID
    ---------- ------------ ---- -------- ---- ----- ------- ------ ------------------- ---------------------- ---------
    172.29.105.3 Nonex-aruba-wlc-1 Building1.floor1 standalone Aruba7210 8.6.0.17_83573 up UPDATE SUCCESSFUL 0 176
    172.29.105.4 None x-aruba-wlc-2 Building1.floor1 standby Aruba7210 8.6.0.17_83573 up UPDATE SUCCESSFUL 0 176

    Total Switches:2
    (lahti-aruba-wlc-1) *[mynode] #show ha group-membership

    Controller member of HA group: HA-group

    Virtual Router 1:
    Description vrrp
    Admin State UP, VR State MASTER
    IP Address 172.x.x.2, MAC Address 00:00:5e:00:01:01, vlan 2756
    Priority 120, Advertisement 1 sec, Preemption Enable Delay 10
    Auth type PASSWORD, Auth data: ********
    tracking is not enabled

    --------
    From wlc-2

    (x-aruba-wlc-2) *[mynode] #show switches

    All Switches
    ------------
    IP Address IPv6 Address Name Location Type Model Version Status Configuration State Config Sync Time (sec) Config ID
    ---------- ------------ ---- -------- ---- ----- ------- ------ ------------------- ---------------------- ---------
    172.29.105.4 None x-aruba-wlc-2 Building1.floor1 standby Aruba7210 8.6.0.17_83573 up UPDATE SUCCESSFUL 10 176

    Total Switches:1
    (x-aruba-wlc-2) *[mynode] #show ha group-membership

    Controller member of HA group:


    Virtual Router 1:
    Description vrrp
    Admin State UP, VR State BACKUP
    IP Address 172.x.x.2, MAC Address 00:00:5e:00:01:01, vlan 2756
    Priority 100, Advertisement 1 sec, Preemption Enable Delay 10
    Auth type PASSWORD, Auth data: ********
    tracking is not enabled

    -------


    What might be wrong in my config and what do I have check/make corrections?

    Br
    Juha-Pekka



    ------------------------------
    Juha-Pekka Lepp�nen
    ------------------------------


  • 2.  RE: AurubaOS 8.6 HA configuration not working

    Posted Apr 24, 2022 04:07 AM
    This is what I see from each WLC's CLI
    AP's are all connected and seen on WLC-1 HA table, WLC-2 has any backup tunnels

    (x-aruba-wlc-1) *[mynode] #show ha ap table

    HA AP Table
    -----------
    AP IP-Address MAC-Address AP-flags HA-flags
    -- ---------- ----------- -------- --------
    lk-site1-8-w1 10.36.208.197 f0:5c:19:c6:6b:f6 sLU
    lk-site2-23-w6 10.36.39.250 f0:5c:19:c7:e7:3e sLU
    lk-site3-14-w1 10.36.23.172 f0:5c:19:c6:69:f8 sLU


    (x-aruba-wlc-2) *[mynode] #show ha ap table

    HA AP Table
    -----------
    AP IP-Address MAC-Address AP-flags HA-flags
    -- ---------- ----------- -------- --------

    Total Num APs::0
    Active APs::0
    Standby APs::0

    ------------------------------
    Juha-Pekka Lepp�nen
    ------------------------------

    Original Message


  • 3.  RE: AurubaOS 8.6 HA configuration not working

    Posted Apr 24, 2022 05:17 AM

    And some more information

    (x-aruba-wlc-1) *[mynode] #show ha ap table

    HA AP Table
    -----------
    AP IP-Address MAC-Address AP-flags HA-flags
    -- ---------- ----------- -------- --------
    lk-site1-8-w1 10.36.208.197 f0:5c:19:c6:6b:f6 sLU
    lk-site2-23-w6 10.36.39.250 f0:5c:19:c7:e7:3e sLU
    lk-site3-14-w1 10.36.23.172 f0:5c:19:c6:69:f8 sLU


    (x-aruba-wlc-1) *[mynode] #show ha group-membership
    Controller member of HA group: HA-group

    (x-aruba-wlc-1) *[mynode] #show running-config | include HA
    Building Configuration...
    ike authentication PRE-SHARE ******
    ha group-profile "HA-group"
    ha group-membership "HA-group"

    ---------------------------------------------------------------------------------


    (x-aruba-wlc-2) *[mynode] #show ha ap table

    HA AP Table
    -----------
    AP IP-Address MAC-Address AP-flags HA-flags
    -- ---------- ----------- -------- --------

    Total Num APs::0
    Active APs::0
    Standby APs: 0

    (lx-aruba-wlc-2) *[mynode] #show ha group-membership
    Controller member of HA group:

    (x-aruba-wlc-2) *[mynode] #show running-config | include HA
    Building Configuration...
    ike authentication PRE-SHARE ******


    ------------



    ------------------------------
    Juha-Pekka Lepp�nen
    ------------------------------

    Original Message


Related Content