AOS 10 supports differing versions of software between gateways and APs, as long as all devices are within an LSR to LSR. Which means that right now AOS 10.4 and 10.7 are supported options.
To see the "recommended version" column on gateways, go to Firmware and show the gateways, or in the case of clusters you'll need to drill into the cluster.
The recommendation, outside of Central's "recommended version" which is based on an algorithm, is to run the same version on AP and gateway when possible.
------------------------------
Carson Hulcher, ACEX#110
------------------------------
Original Message:
Sent: Sep 18, 2024 11:01 AM
From: beconnect
Subject: Newly deployed AP505 show config unsynchronized
Hi.
ok. makes sense
But were can we find the recommended for gateways in Central?
I feel that is more accurate to have GW and AP's in the same version , but i do not see were to find the recommended
Regards
Original Message:
Sent: Sep 18, 2024 10:45 AM
From: chulcher
Subject: Newly deployed AP505 show config unsynchronized
10.6.0.3 is available, that would be preferred over 10.6.0.2 if upgrading. But 10.7 has been released which means that the 10.6 train will be EOL very quickly.
------------------------------
Carson Hulcher, ACEX#110
Original Message:
Sent: Sep 18, 2024 10:39 AM
From: beconnect
Subject: Newly deployed AP505 show config unsynchronized
Hi all
Seems that version 10.6.0.1.89990 on AP 505 puts the radio down
Upgrading to version 10.6.0.2 problem goes away.
yesterday 10.6.0.1 was the recommend version, today is 10.6.0.2
Regards
Original Message:
Sent: Sep 18, 2024 10:14 AM
From: GorazdKikelj
Subject: Newly deployed AP505 show config unsynchronized
Here you can find errors occurred during the deployment of the change. Usually you'll find 3 dots at the event with configuration change that is applied or failed.
Best, Gorazd
------------------------------
Gorazd Kikelj
MVP Guru 2024
Original Message:
Sent: Sep 18, 2024 08:41 AM
From: beconnect
Subject: Newly deployed AP505 show config unsynchronized
Hi
Do you say Configuration audit?
Regards
Original Message:
Sent: Sep 18, 2024 07:21 AM
From: GorazdKikelj
Subject: Newly deployed AP505 show config unsynchronized
Check in audit log for the reason.
Best, Gorazd
------------------------------
Gorazd Kikelj
MVP Guru 2024
Original Message:
Sent: Sep 17, 2024 06:20 PM
From: beconnect
Subject: Newly deployed AP505 show config unsynchronized
Hi Also have similar problem
AP 505 on the same group of the other 505
Config says insyncronized and radios are disable
Original Message:
Sent: Sep 05, 2024 08:02 PM
From: ariyap
Subject: Newly deployed AP505 show config unsynchronized
you can also check the the configuration audit for clues.
------------------------------
If my post was useful accept solution and/or give kudos.
Any opinions expressed here are solely my own and not necessarily that of HPE or Aruba.
Original Message:
Sent: Sep 05, 2024 10:51 AM
From: chulcher
Subject: Newly deployed AP505 show config unsynchronized
Various reasons, usually just requires forcing the sync to fix.
------------------------------
Carson Hulcher, ACEX#110
Original Message:
Sent: Sep 05, 2024 09:33 AM
From: yeowkm
Subject: Newly deployed AP505 show config unsynchronized
recently we deployed a number of new AP505 in Aruba Central.
then we discovered that a few of them is showing config unsynchronized.
what could be the reason. its online n there are clients connecting to them.