Wired Intelligent Edge

 View Only

  • 1.  NO IP ROUTE CONFIGURED

    Posted Apr 25, 2023 05:29 PM

    Hey there
    I have a route configured on a stand alone Aruba 6300M 
    0.0.0.0/0 172.27.1.2
    But when I do a show ip route I get

    No ipv4 routes configured

    I have other switches with the same config and they are working. Any thoughts?



  • 2.  RE: NO IP ROUTE CONFIGURED

    Posted Apr 25, 2023 09:55 PM

    is the interface for 172.27.1.0, up  in the default VRF?
    if the default gateways is not reachable through an interface then it will not show in the routing table.



    ------------------------------
    If my post was useful accept solution and/or give kudos.
    Any opinions expressed here are solely my own and not necessarily that of HPE or Aruba.
    ------------------------------

    Original Message


  • 3.  RE: NO IP ROUTE CONFIGURED

    Posted Apr 25, 2023 11:59 PM
    Tech said it was a known bug on the firmware.
    Upgraded and problem was resolved. Frustrating



    Original Message


  • 4.  RE: NO IP ROUTE CONFIGURED

    Posted Apr 26, 2023 01:33 AM

    what firmware version were you running?



    ------------------------------
    If my post was useful accept solution and/or give kudos.
    Any opinions expressed here are solely my own and not necessarily that of HPE or Aruba.
    ------------------------------

    Original Message


  • 5.  RE: NO IP ROUTE CONFIGURED

    Posted Apr 26, 2023 11:42 AM

    Still having the same behavior once I connected to the network. Anyideas?
    I am using a lag back to our Aruba 8325s

    6300M side
    lag 38
     ports 1/1/49
    ports 1/1/50

    8325 side (Arubacore 1 and Arubacore2)
    lag 38
    ports 1/1/38

     6300M side
    interface lag 38
        no shutdown
        no routing
        vlan trunk native 2701
        vlan trunk allowed all
        lacp mode active
        spanning-tree root-guard
        exit

    8325 cores sides
    ARUBACOREKC1# show ru int lag 38
    interface lag 38
        no shutdown
        description TO SSWC210
        no routing
        vlan trunk native 2701
        vlan trunk allowed all
        lacp mode active
        spanning-tree root-guard
        exit

    I am able to see both Aruba8325 cores

     
    LOCAL-PORT  CHASSIS-ID         PORT-ID                      PORT-DESC                    TTL      SYS-NAME
    -----------------------------------------------------------------------------------------------------------
    1/1/49      b8:d4:e7:41:c3:00  1/1/38                       TO SSWC2210                  120      ARUBACOREKC1
    1/1/50      b8:d4:e7:41:13:00  1/1/38                       TO SSWC2210                  120      ARUBACOREKC2


    default route is 172.27.1.2

    yet when I do a show ip route it says

    SSWC2210# show ip route
     
    No ipv4 routes configured






    Original Message


  • 6.  RE: NO IP ROUTE CONFIGURED

    Posted Apr 26, 2023 11:43 AM

     FL.10.11.1010


    Original Message


  • 7.  RE: NO IP ROUTE CONFIGURED

    Posted Apr 26, 2023 07:22 PM

    please share the output of "show ip int brief" and "show ip route" on the 8325s and the 6300 switches



    ------------------------------
    If my post was useful accept solution and/or give kudos.
    Any opinions expressed here are solely my own and not necessarily that of HPE or Aruba.
    ------------------------------

    Original Message


  • 8.  RE: NO IP ROUTE CONFIGURED

    Posted Apr 27, 2023 01:57 AM

    Do you have two 8325 in a VSX setup?  (Arubacore 1 and Arubacore2)

    Perhaps you should have interface lag 38 multi-chassis?

    running show lacp interfaces to verify the lags are up is also something you may try.



    ------------------------------
    Arne Opdal
    ------------------------------

    Original Message


Related Content