Forum Français

Good afternoon,
There is a problem with port-security settings on HP2530 and HP6000 switches
The essence of the problem is that when configuring, the port is in UP, but the mac address disappears and there is no way to interact with the device, even ping does not pass to the device. A device with a single mac address. When port-security is disabled, the device appears. The setup is only to limit the number of mac addresses. Also, there are no errors in the logs for port-security.

I read somewhere on the forms that for port-security to work, the device must somehow show traffic on the port, after which it is registered and port-security checks are carried out, if the device is silent, then the port will not work. This is not accurate or verified information!

Standard setup on HP6000 port:
interface 1/1/13
    no shutdown
    vlan access 99
    spanning-tree bpdu-guard
    spanning-tree port-type admin-edge
    port-access port-security
        enable
        sticky-learn enable
Standard setup on HP2530 port:
port-security 13 address-limit 1 learn-mode limited-continuous action send-alarm

I read about the keepalive function on ports, but I didn't find it on HP. Maybe someone has encountered this and will tell you?!

Hi Max,

It is the french forum :) 

What firmware on Aruba 6000 ?

Good afternoon,
There is a problem with port-security settings on HP2530 and HP6000 switches
The essence of the problem is that when configuring, the port is in UP, but the mac address disappears and there is no way to interact with the device, even ping does not pass to the device. A device with a single mac address. When port-security is disabled, the device appears. The setup is only to limit the number of mac addresses. Also, there are no errors in the logs for port-security.

I read somewhere on the forms that for port-security to work, the device must somehow show traffic on the port, after which it is registered and port-security checks are carried out, if the device is silent, then the port will not work. This is not accurate or verified information!

Standard setup on HP6000 port:
interface 1/1/13
    no shutdown
    vlan access 99
    spanning-tree bpdu-guard
    spanning-tree port-type admin-edge
    port-access port-security
        enable
        sticky-learn enable
Standard setup on HP2530 port:
port-security 13 address-limit 1 learn-mode limited-continuous action send-alarm

I read about the keepalive function on ports, but I didn't find it on HP. Maybe someone has encountered this and will tell you?!

Perhaps, of course, I asked the wrong question there. But still, this is a technical forum, the technology in every region of the planet is the same.

I want to find the answer here)))

According to the firmware of the switches. HP6000 10.12.1010. HP YA\YB 16.11.0014

Hardware problem on a variety of hardware

Hi Max,

It is the french forum :) 

What firmware on Aruba 6000 ?

Good afternoon,
There is a problem with port-security settings on HP2530 and HP6000 switches
The essence of the problem is that when configuring, the port is in UP, but the mac address disappears and there is no way to interact with the device, even ping does not pass to the device. A device with a single mac address. When port-security is disabled, the device appears. The setup is only to limit the number of mac addresses. Also, there are no errors in the logs for port-security.

I read somewhere on the forms that for port-security to work, the device must somehow show traffic on the port, after which it is registered and port-security checks are carried out, if the device is silent, then the port will not work. This is not accurate or verified information!

Standard setup on HP6000 port:
interface 1/1/13
    no shutdown
    vlan access 99
    spanning-tree bpdu-guard
    spanning-tree port-type admin-edge
    port-access port-security
        enable
        sticky-learn enable
Standard setup on HP2530 port:
port-security 13 address-limit 1 learn-mode limited-continuous action send-alarm

I read about the keepalive function on ports, but I didn't find it on HP. Maybe someone has encountered this and will tell you?!

Hi Max

I think you get more response on wired forum section ;-)

you have the issue with all device ? only some specific device ? 

Perhaps, of course, I asked the wrong question there. But still, this is a technical forum, the technology in every region of the planet is the same.

I want to find the answer here)))

According to the firmware of the switches. HP6000 10.12.1010. HP YA\YB 16.11.0014

Hardware problem on a variety of hardware

Hi Max,

It is the french forum :) 

What firmware on Aruba 6000 ?

Good afternoon,
There is a problem with port-security settings on HP2530 and HP6000 switches
The essence of the problem is that when configuring, the port is in UP, but the mac address disappears and there is no way to interact with the device, even ping does not pass to the device. A device with a single mac address. When port-security is disabled, the device appears. The setup is only to limit the number of mac addresses. Also, there are no errors in the logs for port-security.

I read somewhere on the forms that for port-security to work, the device must somehow show traffic on the port, after which it is registered and port-security checks are carried out, if the device is silent, then the port will not work. This is not accurate or verified information!

Standard setup on HP6000 port:
interface 1/1/13
    no shutdown
    vlan access 99
    spanning-tree bpdu-guard
    spanning-tree port-type admin-edge
    port-access port-security
        enable
        sticky-learn enable
Standard setup on HP2530 port:
port-security 13 address-limit 1 learn-mode limited-continuous action send-alarm

I read about the keepalive function on ports, but I didn't find it on HP. Maybe someone has encountered this and will tell you?!

Hi.

Yes, with all where audi boards, access control systems and security devices are connected, all from different vendors.

Hi Max

I think you get more response on wired forum section ;-)

you have the issue with all device ? only some specific device ? 

Perhaps, of course, I asked the wrong question there. But still, this is a technical forum, the technology in every region of the planet is the same.

I want to find the answer here)))

According to the firmware of the switches. HP6000 10.12.1010. HP YA\YB 16.11.0014

Hardware problem on a variety of hardware

Hi Max,

It is the french forum :) 

What firmware on Aruba 6000 ?

Good afternoon,
There is a problem with port-security settings on HP2530 and HP6000 switches
The essence of the problem is that when configuring, the port is in UP, but the mac address disappears and there is no way to interact with the device, even ping does not pass to the device. A device with a single mac address. When port-security is disabled, the device appears. The setup is only to limit the number of mac addresses. Also, there are no errors in the logs for port-security.

I read somewhere on the forms that for port-security to work, the device must somehow show traffic on the port, after which it is registered and port-security checks are carried out, if the device is silent, then the port will not work. This is not accurate or verified information!

Standard setup on HP6000 port:
interface 1/1/13
    no shutdown
    vlan access 99
    spanning-tree bpdu-guard
    spanning-tree port-type admin-edge
    port-access port-security
        enable
        sticky-learn enable
Standard setup on HP2530 port:
port-security 13 address-limit 1 learn-mode limited-continuous action send-alarm

I read about the keepalive function on ports, but I didn't find it on HP. Maybe someone has encountered this and will tell you?!

Did you check this post?

Here is the document where you can find how to manage silent clients.

Best, Gorazd

Hi.

Yes, with all where audi boards, access control systems and security devices are connected, all from different vendors.

Hi Max

I think you get more response on wired forum section ;-)

you have the issue with all device ? only some specific device ? 

Perhaps, of course, I asked the wrong question there. But still, this is a technical forum, the technology in every region of the planet is the same.

I want to find the answer here)))

According to the firmware of the switches. HP6000 10.12.1010. HP YA\YB 16.11.0014

Hardware problem on a variety of hardware

Hi Max,

It is the french forum :) 

What firmware on Aruba 6000 ?

Good afternoon,
There is a problem with port-security settings on HP2530 and HP6000 switches
The essence of the problem is that when configuring, the port is in UP, but the mac address disappears and there is no way to interact with the device, even ping does not pass to the device. A device with a single mac address. When port-security is disabled, the device appears. The setup is only to limit the number of mac addresses. Also, there are no errors in the logs for port-security.

I read somewhere on the forms that for port-security to work, the device must somehow show traffic on the port, after which it is registered and port-security checks are carried out, if the device is silent, then the port will not work. This is not accurate or verified information!

Standard setup on HP6000 port:
interface 1/1/13
    no shutdown
    vlan access 99
    spanning-tree bpdu-guard
    spanning-tree port-type admin-edge
    port-access port-security
        enable
        sticky-learn enable
Standard setup on HP2530 port:
port-security 13 address-limit 1 learn-mode limited-continuous action send-alarm

I read about the keepalive function on ports, but I didn't find it on HP. Maybe someone has encountered this and will tell you?!