Airheads Volunteer Corps - Support Request

Reply
Highlighted
Occasional Contributor II

AP 375 poor wifi signal

hi,

we have just replaced 3 AP105 with 1 x 375 AP. since there the users in that area are complaining about weak wifi signal in some places, disconnections. I was just thinking how to test the wifi quality, are there any CLI commands, any measurements to be taken during the troubleshooting session ? on the WEB interface of the MM, I can see around 12-15 users connected to this AP, all with good health, on both 2.4 and 5 Ghz. Maybe creating a different AP-group with different EIRP values and move the AP to this group ?

any  ideas ? thanks

Highlighted
MVP Guru

Re: AP 375 poor wifi signal

There could be quite a few reasons, what is the current power levels configured on the AP? What is the area of coverage if you have reduced this from 3x AP-105 to 1x AP-375? 

 

The AP-105 is an indoor AP so therefore will broadcast on indoor channels/power levels by default vs an AP-375 which will broadcast on outdoor channels/power levels.


Depending on your regulatory domain there may you may find these have reduced the power levels and channels/channel widths available to the AP-375 due to the indoor/outdoor regulations.

 

show ap active
show ap allowed-channels ap-name [AP NAME]
show ap allowed-max-EIRP ap-name [AP NAME]


As you can see below from the example, AP-315 vs AP-365

 

(Aruba7030) *[mynode] #show ap allowed-max-EIRP ap-name AP365

Max EIRP setting for AP-365
---------------------------
Channel  1     2     3     4     5     6     7     8     9     10    11    12    13    14  36  40  44  48  52  56  60  64  100   104   108   112   116   120   124   128   132   136   140   144  149   153   157   161   165   169  173
-------  -     -     -     -     -     -     -     -     -     --    --    --    --    --  --  --  --  --  --  --  --  --  ---   ---   ---   ---   ---   ---   ---   ---   ---   ---   ---   ---  ---   ---   ---   ---   ---   ---  ---
b        18.1  18.1  18.1  18.1  18.1  18.1  17.8  17.8  17.8  17.8  17.8  17.5  17.5  *   *   *   *   *   *   *   *   *   *     *     *     *     *     *     *     *     *     *     *     *    *     *     *     *     *     *    *
g/a      19.8  19.8  19.8  19.8  19.8  19.8  19.8  19.8  19.8  19.8  19.8  19.7  19.7  50  50  50  50  50  50  50  50  50  28.4  28.4  28.4  28.4  28.4  28.4  28.4  28.4  28.4  28.3  28.3  50   13.3  13.3  13.3  13.3  13.4  50   50
HT 20    19.8  19.8  19.8  19.8  19.8  19.8  19.5  19.5  19.5  19.6  19.6  19.6  19.6  50  50  50  50  50  50  50  50  50  29.1  29.1  29.1  29.1  29.1  29.1  29.1  29.1  29.1  28.9  28.9  50   13.5  13.4  13.4  13.4  13.5  50   50
HT 40    19.7  19.7  19.7  19.7  19.7  19.8  19.8  19.8  19.8  19.8  19.7  19.7  19.7  50  50  50  50  50  50  50  50  50  29.6  29.6  29.6  29.6  29.6  29.6  29.6  29.6  29.6  29.6  *     50   13.2  13.2  13.3  13.3  *     50   50
VHT 80   *     *     *     *     *     *     *     *     *     *     *     *     *     *   50  50  50  50  50  50  50  50  29.7  29.7  29.7  29.7  29.8  29.8  29.8  29.8  *     *     *     50   13.3  13.3  13.3  13.3  *     50   50
(Aruba7030) *[mynode] #

(Aruba7030) *[mynode] #show ap allowed-max-EIRP ap-name AP315


Max EIRP setting for AP-315
---------------------------
Channel  1     2     3     4     5     6     7     8     9     10    11    12    13    14  36    40    44    48    52    56    60    64    100   104   108   112   116   120   124   128   132   136   140   144  149   153   157   161   165   169  173
-------  -     -     -     -     -     -     -     -     -     --    --    --    --    --  --    --    --    --    --    --    --    --    ---   ---   ---   ---   ---   ---   ---   ---   ---   ---   ---   ---  ---   ---   ---   ---   ---   ---  ---
b        17.0  17.0  17.0  17.0  17.0  16.5  16.5  16.5  17.0  17.0  17.0  17.0  17.0  *   *     *     *     *     *     *     *     *     *     *     *     *     *     *     *     *     *     *     *     *    *     *     *     *     *     *    *
g/a      19.0  19.0  19.0  19.0  19.0  19.0  19.0  19.0  19.0  19.0  19.0  19.0  19.0  *   21.5  21.5  21.5  21.5  21.5  21.5  21.5  21.5  24.5  24.5  24.5  24.5  25.0  25.0  25.0  25.0  25.0  25.0  25.0  *    13.8  13.8  13.6  13.7  13.7  *    *
HT 20    19.5  19.5  19.5  19.5  19.5  19.0  19.0  19.0  19.5  19.5  19.5  19.5  19.5  *   21.5  21.5  21.5  21.5  21.5  21.5  21.5  21.5  29.0  29.0  29.0  29.0  29.0  29.0  29.0  29.0  29.0  29.0  29.0  *    13.7  13.7  13.7  13.7  13.6  *    *
HT 40    19.5  19.5  19.5  19.5  19.5  19.5  19.5  19.5  19.5  19.5  19.5  19.5  19.5  *   22.5  22.5  22.5  22.5  22.5  22.5  22.5  22.5  29.0  29.0  29.0  29.0  29.5  29.5  29.5  29.5  29.5  29.5  *     *    13.7  13.7  13.4  13.4  *     *    *
VHT 80   *     *     *     *     *     *     *     *     *     *     *     *     *     *   22.5  22.5  22.5  22.5  22.5  22.5  22.5  22.5  29.0  29.0  29.0  29.0  28.5  28.5  28.5  28.5  *     *     *     *    13.6  13.6  13.6  13.6  *     *    *
VHT 160  *     *     *     *     *     *     *     *     *     *     *     *     *     *   22.5  22.5  22.5  22.5  22.5  22.5  22.5  22.5  29.5  29.5  29.5  29.5  29.5  29.5  29.5  29.5  *     *     *     *    *     *     *     *     *     *    *
(Aruba7030) *[mynode] #

 


ACMP, ACSA, ACDX #985
If my post addresses your query, give kudos:)
Highlighted

Re: AP 375 poor wifi signal

You can troubleshoot the wireless related issue via Airwave or Dashboard of MM.

Using Airwave you can troubleshoot the issue in details its like a process.

 

as per your issue, it's related to associated and unassociated clients with the poor wifi signal.

 

You can access Airwave and > Client Details in the Clients options tab.

 

enter user mac address or name verify the and details.

Using that you can run command monitor command in the Monitor tab in the Devices tab.

 

>show ap remote debug mgmt-frames ap-name "AP_XXX"

>show ap association ap-name "AP-name=XXX" and etc.

 

 

And Associated Client Diagnostics you can refer in client detail page.

1. clients diagnostics graphs 

2. Associated clients thresholds 

3.Understing the SNR values for signal and noise ratios 

4.Clients Traffic analysis

5. Radio utilization & wireless Quality 

6. Spectrum Analysis 

 

For troubleshooting AP You can use the AP usage graph.

The Devices à Monitor page for controllers and APs includes a graph for users and bandwidth.

 

Pls, a check is RF-mgmt have default EIRP values are not? it's recommended to don't change the EIRP values.

 

Regards,

Suresh

 

 

 

 

 

 

Highlighted
Occasional Contributor II

Re: AP 375 poor wifi signal

Hi Craig,

 

show ap debug driver-log ap-name AP150 | include Tx
1 20.670322 Radio1: Tx power 127.5dBm, Chainmask 2x2
2 27.870915 Radio0: Tx power 127.5dBm, Chainmask 4x4


#show ap active ap-name AP150

Active AP Table
---------------
Name Group IP Address AP Type Flags Uptime Outer IP Cluster Role Radio 0 Band Ch/EIRP/MaxEIRP/Clients Radio 1 Band Ch/EIRP/MaxEIRP/Clients
---- ----- ---------- ------- ----- ------ -------- ------------ ------------------------------------ ------------------------------------
AP150 CH-apgrp 172.22.10.150 375 A2a 92d:22h:55m:22s N/A A/U/SU AP:5GHz-VHT:112E/17.0/30.0/5 AP:2.4GHz-HT:6/15.0/19.7/6

Flags: 1 = 802.1x authenticated AP; 2 = Using IKE version 2;
A = Enet1 in active/standby mode; B = Battery Boost On; C = Cellular;
D = Disconn. Extra Calls On; E = Wired AP enabled; F = AP failed 802.1x authentication;
H = Hotspot Enabled; K = 802.11K Enabled; L = Client Balancing Enabled; M = Mesh;
N = 802.11b protection disabled; P = PPPOE; R = Remote AP;
S = AP connected as standby; X = Maintenance Mode;
a = Reduce ARP packets in the air; d = Drop Mcast/Bcast On; u = Custom-Cert RAP;
i = Provisioned as Indoor; o = Provisioned as Outdoor;
p = Restriction mode in POE-AF/AT;r = 802.11r Enabled; f = No Spectrum FFT support;
Q = DFS CAC timer running; T = Flex Radio Mode is 2.4GHz+5GHz;
U = Flex Radio Mode is 5GHz; V = Flex Radio Mode is 2.4GHz; e = custom EST cert; W = Dual 5GHz Mode Enabled; 4 = Using WiFi Uplink

Channel followed by "*" indicates channel selected due to unsupported configured channel.
"Spectrum" followed by "^" indicates Local Spectrum Override in effect.

Channel flags: +/- = 40 MHz, E = 80 MHz, S = 160 MHz, E+E = 80 + 80 MHz (i.e. 36E+149E)

Cluster Role: U = UAC, A = AAC, SU = Standby UAC , SA = Standby AAC


Num APs:1

80211a ESSID WLAN Stats
----------------------------
Parameter Value
--------- -----
Channel 112
Channel Frame Retry Rate(%) 0
Channel Frame Low Speed Rate(%) 0
Channel Frame Non Unicast Rate(%) 0
Channel Frame Fragmentation Rate(%) 0
Channel Frame Error Rate(%) 0
Channel Bandwidth Rate(kbps) 13
Channel Noise 92
BSSID 48:4a:e9:d8:ad:f0
BSS Frame Retry Rate(%) 0
BSS Frame Low Speed Rate(%) 0
BSS Frame Non Unicast Rate(%) 0
BSS Frame Fragmentation Rate(%) 0
BSS Frame Receive Error Rate(%) 0
BSS Bandwidth Rate(kbps) 5
BSS Tx Packets 203858965
BSS Rx Packets 115172531
BSS Tx Bytes 3074575981
BSS Rx Bytes 2820551933
BSS SNR 25
BSS Tx Rate -
BSS Rx Rate -

 

80211g ESSID WLAN Stats
----------------------------
Parameter Value
--------- -----
Channel 6
Channel Frame Retry Rate(%) 0
Channel Frame Low Speed Rate(%) 0
Channel Frame Non Unicast Rate(%) 0
Channel Frame Fragmentation Rate(%) 0
Channel Frame Error Rate(%) 0
Channel Bandwidth Rate(kbps) 0
Channel Noise 96
BSSID 48:4a:e9:d8:ad:e0
BSS Frame Retry Rate(%) 0
BSS Frame Low Speed Rate(%) 0
BSS Frame Non Unicast Rate(%) 0
BSS Frame Fragmentation Rate(%) 0
BSS Frame Receive Error Rate(%) 0
BSS Bandwidth Rate(kbps) 0
BSS Tx Packets 619590946
BSS Rx Packets 495324954
BSS Tx Bytes 619443874
BSS Rx Bytes 4092363375
BSS SNR 25
BSS Tx Rate N/A
BSS Rx Rate N/A


#show ap allowed-channels ap-name AP150

Allowed Channels for AP "AP150"
----------------------------------------------------------------------------
PHY Type Allowed Channels
-------- ----------------
802.11g (indoor) 1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (indoor) 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
802.11g (outdoor) 1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (outdoor) 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
802.11g 40MHz (indoor) 1-5 2-6 3-7 4-8 5-9 6-10 7-11 8-12 9-13
802.11a 40MHz (indoor) 36-40 44-48 52-56 60-64 100-104 108-112 116-120 124-128 132-136 149-153 157-161
802.11g 40MHz (outdoor) 1-5 2-6 3-7 4-8 5-9 6-10 7-11 8-12 9-13
802.11a 40MHz (outdoor) 100-104 108-112 116-120 124-128 132-136 149-153 157-161
802.11a 80MHz (indoor) 36-48 52-64 100-112 116-128 149-161
802.11a 80MHz (outdoor) 100-112 116-128 149-161
802.11a 160MHz (indoor) 36-64 100-128
802.11a 160MHz (outdoor) 100-128
802.11a (DFS) 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140

 

#show ap allowed-max-EIRP ap-name AP150

Warning: This command has been deprecated.

Max EIRP setting for AP-375
---------------------------
Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 144 149 153 157 161 165 169 173
------- - - - - - - - - - -- -- -- -- -- -- -- -- -- -- -- -- -- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
b 17.6 17.6 17.6 17.6 17.6 17.6 17.3 17.3 17.3 17.3 17.3 17.3 17.3 * * * * * * * * * * * * * * * * * * * * * * * * * * * *
g/a 19.4 19.4 19.4 19.4 19.4 19.4 19.4 19.7 19.7 19.7 19.7 19.7 19.7 * * * * * * * * * 27.9 27.9 27.9 27.9 27.9 27.9 27.9 27.9 27.9 27.7 27.7 * 13.3 13.3 13.5 13.5 13.8 * *
HT 20 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.5 19.5 * * * * * * * * * 28.8 28.8 28.8 28.8 28.8 28.8 28.8 28.8 28.8 28.2 28.2 * 13.6 13.4 13.4 13.4 13.6 * *
HT 40 19.5 19.5 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.6 19.6 * * * * * * * * * 29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 * * 13.5 13.5 13.8 13.8 * * *
VHT 80 * * * * * * * * * * * * * * * * * * * * * * 29.5 29.5 29.5 29.5 29.5 29.5 29.5 29.5 * * * * 13.6 13.6 13.6 13.6 * * *
VHT 160 * * * * * * * * * * * * * * * * * * * * * * 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 * * * * * * * * * * *

 

Highlighted
Occasional Contributor II

Re: AP 375 poor wifi signal

thank you Craig,

 

show ap debug driver-log ap-name AP150 | include Tx
1 20.670322 Radio1: Tx power 127.5dBm, Chainmask 2x2
2 27.870915 Radio0: Tx power 127.5dBm, Chainmask 4x4


#show ap active ap-name AP150

Active AP Table
---------------
Name Group IP Address AP Type Flags Uptime Outer IP Cluster Role Radio 0 Band Ch/EIRP/MaxEIRP/Clients Radio 1 Band Ch/EIRP/MaxEIRP/Clients
---- ----- ---------- ------- ----- ------ -------- ------------ ------------------------------------ ------------------------------------
AP150 CH-apgrp 172.22.10.150 375 A2a 92d:22h:55m:22s N/A A/U/SU AP:5GHz-VHT:112E/17.0/30.0/5 AP:2.4GHz-HT:6/15.0/19.7/6

Flags: 1 = 802.1x authenticated AP; 2 = Using IKE version 2;
A = Enet1 in active/standby mode; B = Battery Boost On; C = Cellular;
D = Disconn. Extra Calls On; E = Wired AP enabled; F = AP failed 802.1x authentication;
H = Hotspot Enabled; K = 802.11K Enabled; L = Client Balancing Enabled; M = Mesh;
N = 802.11b protection disabled; P = PPPOE; R = Remote AP;
S = AP connected as standby; X = Maintenance Mode;
a = Reduce ARP packets in the air; d = Drop Mcast/Bcast On; u = Custom-Cert RAP;
i = Provisioned as Indoor; o = Provisioned as Outdoor;
p = Restriction mode in POE-AF/AT;r = 802.11r Enabled; f = No Spectrum FFT support;
Q = DFS CAC timer running; T = Flex Radio Mode is 2.4GHz+5GHz;
U = Flex Radio Mode is 5GHz; V = Flex Radio Mode is 2.4GHz; e = custom EST cert; W = Dual 5GHz Mode Enabled; 4 = Using WiFi Uplink

Channel followed by "*" indicates channel selected due to unsupported configured channel.
"Spectrum" followed by "^" indicates Local Spectrum Override in effect.

Channel flags: +/- = 40 MHz, E = 80 MHz, S = 160 MHz, E+E = 80 + 80 MHz (i.e. 36E+149E)

Cluster Role: U = UAC, A = AAC, SU = Standby UAC , SA = Standby AAC


Num APs:1

80211a ESSID WLAN Stats
----------------------------
Parameter Value
--------- -----
Channel 112
Channel Frame Retry Rate(%) 0
Channel Frame Low Speed Rate(%) 0
Channel Frame Non Unicast Rate(%) 0
Channel Frame Fragmentation Rate(%) 0
Channel Frame Error Rate(%) 0
Channel Bandwidth Rate(kbps) 13
Channel Noise 92
BSSID 48:4a:e9:d8:ad:f0
BSS Frame Retry Rate(%) 0
BSS Frame Low Speed Rate(%) 0
BSS Frame Non Unicast Rate(%) 0
BSS Frame Fragmentation Rate(%) 0
BSS Frame Receive Error Rate(%) 0
BSS Bandwidth Rate(kbps) 5
BSS Tx Packets 203858965
BSS Rx Packets 115172531
BSS Tx Bytes 3074575981
BSS Rx Bytes 2820551933
BSS SNR 25
BSS Tx Rate -
BSS Rx Rate -

 

80211g ESSID WLAN Stats
----------------------------
Parameter Value
--------- -----
Channel 6
Channel Frame Retry Rate(%) 0
Channel Frame Low Speed Rate(%) 0
Channel Frame Non Unicast Rate(%) 0
Channel Frame Fragmentation Rate(%) 0
Channel Frame Error Rate(%) 0
Channel Bandwidth Rate(kbps) 0
Channel Noise 96
BSSID 48:4a:e9:d8:ad:e0
BSS Frame Retry Rate(%) 0
BSS Frame Low Speed Rate(%) 0
BSS Frame Non Unicast Rate(%) 0
BSS Frame Fragmentation Rate(%) 0
BSS Frame Receive Error Rate(%) 0
BSS Bandwidth Rate(kbps) 0
BSS Tx Packets 619590946
BSS Rx Packets 495324954
BSS Tx Bytes 619443874
BSS Rx Bytes 4092363375
BSS SNR 25
BSS Tx Rate N/A
BSS Rx Rate N/A


#show ap allowed-channels ap-name AP150

Allowed Channels for AP "AP150"
----------------------------------------------------------------------------
PHY Type Allowed Channels
-------- ----------------
802.11g (indoor) 1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (indoor) 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
802.11g (outdoor) 1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (outdoor) 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
802.11g 40MHz (indoor) 1-5 2-6 3-7 4-8 5-9 6-10 7-11 8-12 9-13
802.11a 40MHz (indoor) 36-40 44-48 52-56 60-64 100-104 108-112 116-120 124-128 132-136 149-153 157-161
802.11g 40MHz (outdoor) 1-5 2-6 3-7 4-8 5-9 6-10 7-11 8-12 9-13
802.11a 40MHz (outdoor) 100-104 108-112 116-120 124-128 132-136 149-153 157-161
802.11a 80MHz (indoor) 36-48 52-64 100-112 116-128 149-161
802.11a 80MHz (outdoor) 100-112 116-128 149-161
802.11a 160MHz (indoor) 36-64 100-128
802.11a 160MHz (outdoor) 100-128
802.11a (DFS) 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140

 

#show ap allowed-max-EIRP ap-name AP150

Warning: This command has been deprecated.

Max EIRP setting for AP-375
---------------------------
Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 144 149 153 157 161 165 169 173
------- - - - - - - - - - -- -- -- -- -- -- -- -- -- -- -- -- -- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
b 17.6 17.6 17.6 17.6 17.6 17.6 17.3 17.3 17.3 17.3 17.3 17.3 17.3 * * * * * * * * * * * * * * * * * * * * * * * * * * * *
g/a 19.4 19.4 19.4 19.4 19.4 19.4 19.4 19.7 19.7 19.7 19.7 19.7 19.7 * * * * * * * * * 27.9 27.9 27.9 27.9 27.9 27.9 27.9 27.9 27.9 27.7 27.7 * 13.3 13.3 13.5 13.5 13.8 * *
HT 20 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.5 19.5 * * * * * * * * * 28.8 28.8 28.8 28.8 28.8 28.8 28.8 28.8 28.8 28.2 28.2 * 13.6 13.4 13.4 13.4 13.6 * *
HT 40 19.5 19.5 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.6 19.6 * * * * * * * * * 29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 * * 13.5 13.5 13.8 13.8 * * *
VHT 80 * * * * * * * * * * * * * * * * * * * * * * 29.5 29.5 29.5 29.5 29.5 29.5 29.5 29.5 * * * * 13.6 13.6 13.6 13.6 * * *
VHT 160 * * * * * * * * * * * * * * * * * * * * * * 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 * * * * * * * * * * *

 

Highlighted
Occasional Contributor II

Re: AP 375 poor wifi signal

show ap debug driver-log ap-name AP150 | include Tx
1 20.670322 Radio1: Tx power 127.5dBm, Chainmask 2x2
2 27.870915 Radio0: Tx power 127.5dBm, Chainmask 4x4


#show ap active ap-name AP150

Active AP Table
---------------
Name Group IP Address AP Type Flags Uptime Outer IP Cluster Role Radio 0 Band Ch/EIRP/MaxEIRP/Clients Radio 1 Band Ch/EIRP/MaxEIRP/Clients
---- ----- ---------- ------- ----- ------ -------- ------------ ------------------------------------ ------------------------------------
AP150 CH-apgrp 172.22.10.150 375 A2a 92d:22h:55m:22s N/A A/U/SU AP:5GHz-VHT:112E/17.0/30.0/5 AP:2.4GHz-HT:6/15.0/19.7/6

Flags: 1 = 802.1x authenticated AP; 2 = Using IKE version 2;
A = Enet1 in active/standby mode; B = Battery Boost On; C = Cellular;
D = Disconn. Extra Calls On; E = Wired AP enabled; F = AP failed 802.1x authentication;
H = Hotspot Enabled; K = 802.11K Enabled; L = Client Balancing Enabled; M = Mesh;
N = 802.11b protection disabled; P = PPPOE; R = Remote AP;
S = AP connected as standby; X = Maintenance Mode;
a = Reduce ARP packets in the air; d = Drop Mcast/Bcast On; u = Custom-Cert RAP;
i = Provisioned as Indoor; o = Provisioned as Outdoor;
p = Restriction mode in POE-AF/AT;r = 802.11r Enabled; f = No Spectrum FFT support;
Q = DFS CAC timer running; T = Flex Radio Mode is 2.4GHz+5GHz;
U = Flex Radio Mode is 5GHz; V = Flex Radio Mode is 2.4GHz; e = custom EST cert; W = Dual 5GHz Mode Enabled; 4 = Using WiFi Uplink

Channel followed by "*" indicates channel selected due to unsupported configured channel.
"Spectrum" followed by "^" indicates Local Spectrum Override in effect.

Channel flags: +/- = 40 MHz, E = 80 MHz, S = 160 MHz, E+E = 80 + 80 MHz (i.e. 36E+149E)

Cluster Role: U = UAC, A = AAC, SU = Standby UAC , SA = Standby AAC


Num APs:1

80211a ESSID WLAN Stats
----------------------------
Parameter Value
--------- -----
Channel 112
Channel Frame Retry Rate(%) 0
Channel Frame Low Speed Rate(%) 0
Channel Frame Non Unicast Rate(%) 0
Channel Frame Fragmentation Rate(%) 0
Channel Frame Error Rate(%) 0
Channel Bandwidth Rate(kbps) 13
Channel Noise 92
BSSID 48:4a:e9:d8:ad:f0
BSS Frame Retry Rate(%) 0
BSS Frame Low Speed Rate(%) 0
BSS Frame Non Unicast Rate(%) 0
BSS Frame Fragmentation Rate(%) 0
BSS Frame Receive Error Rate(%) 0
BSS Bandwidth Rate(kbps) 5
BSS Tx Packets 203858965
BSS Rx Packets 115172531
BSS Tx Bytes 3074575981
BSS Rx Bytes 2820551933
BSS SNR 25
BSS Tx Rate -
BSS Rx Rate -

 

80211g ESSID WLAN Stats
----------------------------
Parameter Value
--------- -----
Channel 6
Channel Frame Retry Rate(%) 0
Channel Frame Low Speed Rate(%) 0
Channel Frame Non Unicast Rate(%) 0
Channel Frame Fragmentation Rate(%) 0
Channel Frame Error Rate(%) 0
Channel Bandwidth Rate(kbps) 0
Channel Noise 96
BSSID 48:4a:e9:d8:ad:e0
BSS Frame Retry Rate(%) 0
BSS Frame Low Speed Rate(%) 0
BSS Frame Non Unicast Rate(%) 0
BSS Frame Fragmentation Rate(%) 0
BSS Frame Receive Error Rate(%) 0
BSS Bandwidth Rate(kbps) 0
BSS Tx Packets 619590946
BSS Rx Packets 495324954
BSS Tx Bytes 619443874
BSS Rx Bytes 4092363375
BSS SNR 25
BSS Tx Rate N/A
BSS Rx Rate N/A


#show ap allowed-channels ap-name AP150

Allowed Channels for AP "AP150"
----------------------------------------------------------------------------
PHY Type Allowed Channels
-------- ----------------
802.11g (indoor) 1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (indoor) 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
802.11g (outdoor) 1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (outdoor) 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
802.11g 40MHz (indoor) 1-5 2-6 3-7 4-8 5-9 6-10 7-11 8-12 9-13
802.11a 40MHz (indoor) 36-40 44-48 52-56 60-64 100-104 108-112 116-120 124-128 132-136 149-153 157-161
802.11g 40MHz (outdoor) 1-5 2-6 3-7 4-8 5-9 6-10 7-11 8-12 9-13
802.11a 40MHz (outdoor) 100-104 108-112 116-120 124-128 132-136 149-153 157-161
802.11a 80MHz (indoor) 36-48 52-64 100-112 116-128 149-161
802.11a 80MHz (outdoor) 100-112 116-128 149-161
802.11a 160MHz (indoor) 36-64 100-128
802.11a 160MHz (outdoor) 100-128
802.11a (DFS) 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140

 

#show ap allowed-max-EIRP ap-name AP150

Warning: This command has been deprecated.

Max EIRP setting for AP-375
---------------------------
Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 144 149 153 157 161 165 169 173
------- - - - - - - - - - -- -- -- -- -- -- -- -- -- -- -- -- -- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
b 17.6 17.6 17.6 17.6 17.6 17.6 17.3 17.3 17.3 17.3 17.3 17.3 17.3 * * * * * * * * * * * * * * * * * * * * * * * * * * * *
g/a 19.4 19.4 19.4 19.4 19.4 19.4 19.4 19.7 19.7 19.7 19.7 19.7 19.7 * * * * * * * * * 27.9 27.9 27.9 27.9 27.9 27.9 27.9 27.9 27.9 27.7 27.7 * 13.3 13.3 13.5 13.5 13.8 * *
HT 20 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.7 19.5 19.5 * * * * * * * * * 28.8 28.8 28.8 28.8 28.8 28.8 28.8 28.8 28.8 28.2 28.2 * 13.6 13.4 13.4 13.4 13.6 * *
HT 40 19.5 19.5 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.6 19.6 * * * * * * * * * 29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 * * 13.5 13.5 13.8 13.8 * * *
VHT 80 * * * * * * * * * * * * * * * * * * * * * * 29.5 29.5 29.5 29.5 29.5 29.5 29.5 29.5 * * * * 13.6 13.6 13.6 13.6 * * *
VHT 160 * * * * * * * * * * * * * * * * * * * * * * 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 * * * * * * * * * * *

 

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: