Command of the Day

Reply
Guru Elite

COTD: ap-leds (AP12x and 5W only)

Ever wanted to identify that AP that is right above you? The "ap-leds" command in enable mode can make an ap or group of aps blink to let you know. This only works on the AP12x and 5Wx aps. Command usage is below:

(M3.arubanetworks.com) #ap-leds ?
all Control LEDs on all APs
ap-group Control LEDs on APs in this group
ap-name Control LEDs on AP with this name
ip-addr Control LEDs on AP at this IP address
wired-mac Control LEDs on AP at this MAC address

(M3.arubanetworks.com) #ap-leds ap-name conference-room-1 ?
blink Make LEDs blink for identification
normal Restore LEDs to their normal behavior

(M3.arubanetworks.com) #ap-leds ap-name conference-room-1 blink

*Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.*
ArubaOS 8.4 User Guide
InstantOS 8.3 User Guide
Airheads Knowledgebase
Airheads Learning Videos
Aruba Central Documentation
Sign up for Security Alerts
Aruba Technical Webinars
Occasional Contributor I

ap-leds ???? ap-105

I had a customer ask if the leds can be turned off.
Guru Elite

Leds




In the AP system-profile of that AP group, there is an option to either turn the LEDs of the AP125s off, or allow them to operate normally.


*Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.*
ArubaOS 8.4 User Guide
InstantOS 8.3 User Guide
Airheads Knowledgebase
Airheads Learning Videos
Aruba Central Documentation
Sign up for Security Alerts
Aruba Technical Webinars
Occasional Contributor II

Re: COTD: ap-leds (AP12x and 5W only)


Ever wanted to identify that AP that is right above you? The "ap-leds" command in enable mode can make an ap or group of aps blink to let you know. This only works on the AP12x and 5Wx aps. Command usage is below:

(M3.arubanetworks.com) #ap-leds ?
all Control LEDs on all APs
ap-group Control LEDs on APs in this group
ap-name Control LEDs on AP with this name
ip-addr Control LEDs on AP at this IP address
wired-mac Control LEDs on AP at this MAC address

(M3.arubanetworks.com) #ap-leds ap-name conference-room-1 ?
blink Make LEDs blink for identification
normal Restore LEDs to their normal behavior

(M3.arubanetworks.com) #ap-leds ap-name conference-room-1 blink




Is this valid in AOS 3.3? It doesn't seem to be a recognized command.
(Aruba-Resnick-1) #ap-leds ?

(Aruba-Resnick-1) #ap-leds
Guru Elite

Config T

Try config t, first.

*Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.*
ArubaOS 8.4 User Guide
InstantOS 8.3 User Guide
Airheads Knowledgebase
Airheads Learning Videos
Aruba Central Documentation
Sign up for Security Alerts
Aruba Technical Webinars
Occasional Contributor II

Re: COTD: ap-leds (AP12x and 5W only)

no dice.

(Aruba-Resnick-1) (config) #ap-leds ?

(Aruba-Resnick-1) (config) #ap-leds

I've also tried the full command ap-leds ap-name R-Bel14-1402 blink in both enable and conf modes, but no success.
Guru Elite

Version

This is only available in 3.4.x and above... Sorry about that.

*Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.*
ArubaOS 8.4 User Guide
InstantOS 8.3 User Guide
Airheads Knowledgebase
Airheads Learning Videos
Aruba Central Documentation
Sign up for Security Alerts
Aruba Technical Webinars
Occasional Contributor II

Re: COTD: ap-leds (AP12x and 5W only)

Understood. Thanks for the answer.
Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: