Controllerless Networks

Hi ALL

 

i need to install in main site to MM-VA controllers that act as

mm-master and mm-backup and in local branches (10 sites)

need to install HW controller 7010 model that will synch from and to

the MM-VA for licence and configuration ...

1- this scenario valid?

2-if no what is my option?

3-if yes .. can you please explain how ? (vrrp ?LMS)

because i very confused when i turn on the controler what mode i need to choose if i want the controler to be MD ?

 

it will very help me if you can post a exmpale .

BR Avi

If I understand you correct, you would first install the the 2 MM-VAs at a central site with a VRRP between them to manage the configuration and licensing of all of your 7010s.  Later when you configure the 7010s, they should be MDs (controllers that serve access points and clients) and point them to the VRRP ip address between the 2 MM-VAs.  You would add the licenses to the MM-VAs.

 

Have you seen the ArubaOS 8 fundamentals guide here?  https://community.arubanetworks.com/t5/Controller-Based-WLANs/ArubaOS-8-Fundamentals-Guide/ta-p/428914

 

Also please look at the ArubaOS 8.2 videos below.

Hi 

i read the guides and still i am very confused... 

when i turn on  from the box the controller in wich mode should i pick for 

MD ?

can somone print the cli command for enter or config MD to manage in the MM ?

i get how to config and i config in the past two contrroller in mobility mastery/mobility backup ,ode with VRRP and its working graet BUT 

the MM and MD i not understand yet...

 

Br Avi 

Following these instructions :

How to deploy Mobility Master
https://ase.arubanetworks.com/solutions/id/139

How to deploy MM and Backup MM
https://ase.arubanetworks.com/solutions/id/146

Licensing
https://ase.arubanetworks.com/solutions/id/154

How to add Mobility Controllers in the MM
https://ase.arubanetworks.com/solutions/id/153





Thank you

Victor Fabian

Pardon typos sent from Mobile

Thanks its working

now how i add IAP to MD ?

i enter the instant and converting and then i config the ip of the MD controller and its not working ..

 

what i doing wrong.. ?

Thanks

 

Configure the Configuration > “default” AP group > LMS to point to the controller mgmt IP Address



Thank you

Victor Fabian

Pardon typos sent from Mobile

Hi Victor

 

i config in the MD the lms ip and connect the ap directly to the controller

and then enter to the iap and direct to the MD ip and still not working ..

 

i miss somthing ?

Thanks

Are you able to see the controller?
Did you apply the licenses ?
Can you ping the controller from the AP network ?
Do you see any alerts (error messages) at the top ?



Thank you

Victor Fabian

Pardon typos sent from Mobile

Hi Victor 

First Thank you.

i set the net in my lab first and only for the tests the MM-VA and the MD

are on the same Lan , in the MM i see the controller and its ok i installed global license .

can you please tell me what is the procedure when you what to connect iap to this setup?(MM and MD)

Thanks

Hi

now its working because when i connected directly to wired port

int the MD controller i need to authenticate and thats the reason why

the AP fail to connect the controller .

 

BUT how can i fix this issue i dont want wired client authenticated at all .

i want that the MD controller switch port will be open .

 

how can i fix this ?

THANKS .

In the MD on that interface it should be "trusted"

 

 

Thanks All for your Help !!

its working great forum .

i read the guides and still i am very confused...

 

___________________________________________

Redtube Beeg Spankbang 

Hi Blanca12

 

look at this links :

.https://ase.arubanetworks.com/solutions/id/141

https://www.arubanetworks.com/techdocs/ArubaOS_64x_WebHelp/Content/ArubaFrameStyles/1CommandList/aaa_authentication_wired.htm

 

hope it will help you.