Controllerless Networks

Hi

 

I can´t conver an IAP 105 to AP 105

 

I log in to instant and put the ip address of my controller 10.9.4.99 and gett a message saying status not available.

 

What is the problem ? IAP need to ping the controller ? IAP does not have an IP, so how is the conversion done ? Does the IAP contacts the Aruba Controller?

 

I am not able to do the conversion

 

My controller is 3200xm ( 6.2.0.3)  and IAP is :

 

9c:1c:12:c9:08:2c# show version
Aruba Operating System Software.
ArubaOS (MODEL: 105), Version 6.2.1.0-3.3.0.3

 

Can you help ?

Yes.....IAP needs to be able to talk to the controller and needs an IP address to do so.

Please make sure that you IAP can communicate (PING) to the controller and regulatory domain of both IAP and controller are same.

IAP not getting dhcp ip address..

 

I am going to try to put a static one and see if it works

OK

 

Done.

 

it seems that we have one switch bad.. Dhcp is on Datacenter and we pass bettween 3 floor switches.

 

When i Changed to another switch everything is ok !

 

Thanks for the help

IAP is converted to AP 105, but only shows 11A/N led.

 

The 11 B/G/N is off. Do you know why? It only appens on one of the ap´s

 

tks

Have you provisioned the AP?

What does your SSID profile look like?  Do you you have it set to only advertise on the 5GHz radio or both?

Both..

I test it with another ap and both leds are green
Bruno Costa

CONNECTing . . .
Projectos e Consultoria Lda.
Rua Diogo de Silves, 33C
Restelo
1400-107 Lisboa
PORTUGAL
Tlf:    +351-213031100
Fax:  +351-213031117
Tlm:   +351-916158228
EMail: baraujo@connecting.pt

What version of SW is running on your controller? May need to update.

What is the regulatory domain of your IAP?  You can see that on the white part# sticker on the back of the AP. Ex: IAP-105-US.

What is the regulatory domain of your controller?

What Country Code are you setting for your APs?

Is the other, working, AP and IAP-105 or a regular AP-105?

Hi marcos

Running 6.3 on Controller

Both are IAP ?s running PT country code


I?ve checked on Controller and all seem fine on the radios

I?ve never seen but could be a led error?

Because I see both radios UP in ap config on controller


Bruno Costa
IT User Support Specialist
Information Technology
Building Efficiency
Tel: +351 210 940 066
Mob: +351 916 158 228
Fax: +351 219 598 084
E-mail: Bruno.Costa-EXT@jci.com
Internet: www.johnsoncontrols.com

Johnson Controls
Building Efficiency
Av. do Forte, 12
Carnaxide
2790-072
Portugal


Johnson Controls Portugal BE Lda, a company registered in Portugal. Avenida do Forte, Edificio Tetrapak, Parish of Carnaxide, Oeiras, Portugal. Registered number: 505206790. For further details please click here.

This email transmission may be confidential and is intended solely for the person or organisation to which it is addressed. If you are not the intended recipient, you must not copy, distribute or disseminate the information, or act in reliance upon it. Any views expressed in this message are those of the individual sender, except where the sender specifically states them to be the views of any organisation or employer. If you have received this message in error, do not open any attachment but please notify the sender and delete this message from your system. This email may be covered by legal, professional or other privilege. Please rely on your own virus check as no responsibility is taken by the sender for any damage arising as a result of any virus or similar infection contained herein.

It could be a regulatory domain mis-match.  If the AP is a -US model it will not come up on a -ROW controller.  It may be worth checking but you need to look at the back of the AP.

 

I have not seen LEDs fail; however, if the radio is working and clients can connect it may be.  If this is the case you should open a case with TAC.

If it is a LED failure you shoudl still be able to see both radio for that AP when you do a show ap bss-table.