Controllerless Networks

Reply
Highlighted
Aruba Employee

Re: iap-325 in mesh doesn't respect power settings

I experience the same issue in all 8.x versions

 

Wired:

lebele_0-1586189228327.png

 


IAP275# show aps

2 Access Points
---------------
Name IP Address Mode Spectrum Clients Type IPv6 Address Mesh Role Zone Serial # radio0 Channel radio0 Power (dBm) radio0 Utilization (%) radio0 Noise Floor (dBm) radio1 Channel radio1 Power (dBm) radio1 Utilization (%) radio1 Noise Floor (dBm) radio2 Channel radio2 Power (dBm) radio2 Utilization (%) radio2 Noise Floor (dBm) Need Antenna Config From Port Config Id Config Csum Ext SSID Active Age Link Local IP Address Uplink Port
---- ---------- ---- -------- ------- ---- ------------ --------- ---- -------- -------------- ------------------ ---------------------- ------------------------ -------------- ------------------ ---------------------- ------------------------ -------------- ------------------ ---------------------- ------------------------ ------------------- --------- --------- ----------- --------------- --- --------------------- -----------
IAP275 192.168.30.109* access disable 1 275(outdoor) -- Portal - CL0016483 64 12 1(good) -96(good) 11 9 32(good) -96(good) - - - - No none 4 41017 disable 16h:43m:9s -- eth0
IAP515 192.168.7.35 access disable 0 515(indoor) -- N/A - CNHQKD5D12 40 12 9(good) -93(good) 6 9 37(good) -89(good) - - - - No none 4 41017 enable 4m:35s fe80::f62e:7fff:fec9:7040 eth0

 

 

Meshed:

lebele_1-1586189280170.png

 

 

IAP275# show aps

2 Access Points
---------------
Name IP Address Mode Spectrum Clients Type IPv6 Address Mesh Role Zone Serial # radio0 Channel radio0 Power (dBm) radio0 Utilization (%) radio0 Noise Floor (dBm) radio1 Channel radio1 Power (dBm) radio1 Utilization (%) radio1 Noise Floor (dBm) radio2 Channel radio2 Power (dBm) radio2 Utilization (%) radio2 Noise Floor (dBm) Need Antenna Config From Port Config Id Config Csum Ext SSID Active Age Link Local IP Address Uplink Port
---- ---------- ---- -------- ------- ---- ------------ --------- ---- -------- -------------- ------------------ ---------------------- ------------------------ -------------- ------------------ ---------------------- ------------------------ -------------- ------------------ ---------------------- ------------------------ ------------------- --------- --------- ----------- --------------- --- --------------------- -----------
IAP275 192.168.30.109* access disable 1 275(outdoor) -- Portal - CL0016483 64 12 1(good) -96(good) 11 9 21(good) -96(good) - - - - No none 4 41017 disable 16h:47m:47s -- eth0
IAP515 192.168.30.79 access disable 0 515(indoor) -- Point - CNHQKD5D12 64 30 1(good) -92(good) 6 9 32(good) -91(good) - - - - No none 4 41017 disable 35s -- Wifi-mesh
IAP275#

Highlighted
Occasional Contributor II

iap-325 in mesh doesn't respect power settings

Hi!

 

I have mesh built from iap-345 (wired) and iap-325 (wireless).

power limits are 12-18 for 2.4g and 18-24 for 5g.

despite limits iap-325 shows 30db for 5g and 26db for 2.4g, causing clients to stick to it, as signal is stronger even when standing next to iap-345.

 

both AP running 8.6.0.3

 

thanks!

Highlighted

Re: iap-325 in mesh doesn't respect power settings

Where/how are you determining the output power?


Charlie Clemmer
Aruba Customer Engineering
Highlighted
Occasional Contributor II

Re: iap-325 in mesh doesn't respect power settings

Hi!

 

thanks for response.

 

IAP-325# show ap bss-table

Aruba AP BSS Table
------------------
bss ess port ip phy type ch/EIRP/max-EIRP cur-cl ap name in-t(s) tot-t flags
--- --- ---- -- --- ---- ---------------- ------ ------- ------- ----- -----
b4:5d:50:d8:b7:12 home-net ?/? 192.168.0.6 a-VHT ap 149E/32.9/32.9 1 IAP-325 0 13h:50m:26s K
b4:5d:50:d8:b7:02 home-net ?/? 192.168.0.6 g-HT ap 7+/15.0/26.7 1 IAP-325 0 13h:50m:25s K

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: