Network Management

Reply
New Contributor

Airwave 8.2.10.0

Hi, I just updated Airwave from 8.2.9.1 to 8.2.10.0. After the virtual machine has restarted I cannot log in with "ampadmin -password". Does anyone know if they have been changing credentials?

 

 

Paolo D'antona

Contributor II

Re: Airwave 8.2.10.0

i just upgraded my lab VM and the ampadmin account was that same as before the upgrade(ie username ampadmin).  So I dont think its changed.

Occasional Contributor II

Re: Airwave 8.2.10.0

As alow has already said, the username did not change. I using "admin" and it still works in 8.2.10.0.

New Contributor

Re: Airwave 8.2.10.0

It's not *supposed* to affect upgrades, but this might be relevant:

amp-pw.jpg

Sauce: https://support.hpe.com/hpsc/doc/public/display?docId=a00090980en_us

MVP Expert

Re: Airwave 8.2.10.0

It should still work. I upgraded yesterday and didnt find any issue with it. Hope you didnt run out of disk space on the server. ampadmin login wouldnt work sometimes when we run out of disk space/DB is down.

 

Regards,
Vishnu
If my post helped you, don't forget to give kudos ;)
Contributor I

Re: Airwave 8.2.10.0

Hi,

 

i haven't the same issue, but an issue with the login after updating to 8.2.10.0.

I use "LDAP Authentication and Authorization".
After the update, no one can login to airwave (WebGUI) via LDAP.

I thought it was maybe the mentioned above password policy, so i changed the password to hit the airwave-password-policy, but it didn't work.

Has somebody an idea?

Aruba Employee

Re: Airwave 8.2.10.0

One thing to try - Remove the LDAP settings in AMP and Readd the details to see if LDAP auth works.

Contributor I

Re: Airwave 8.2.10.0


@Gowri Amujuri wrote:

One thing to try - Remove the LDAP settings in AMP and Readd the details to see if LDAP auth works.


No. Still doesn't work.

Is there a log-file, where i can see ldap-authentication-attempts?
I created a diagnostic-file und looked (grep) thru all the logfiles, but the only thing i could find (in /var/log/amp_events) was ""Failed login attempt".
Or is there anywhere a setting, where i can increase the loglevel for ldap logs?

 

P.S.
I've manually tested it (ldapsearch on my pc) with the same settings and it worked. So the LDAP-Service /-Server works fine.

MVP Guru

Re: Airwave 8.2.10.0

No,we dont have specific log to check for LDAP related login issues, we need to take packetcapture  from CLI during login failed attempts to see whether proper role or any request been sent to Airwave or LDAP.

 

Make sure to enter complete base DN name where users are located and also check for Bind password details are correct. If everything is fine but still see auth failures, I would recommand to open TAC ticket.

Regards,
Pavan
If my post address your queries, give kudos and accept as solution!
NOTE: Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba or Hewlett Packard Enterprise.
Highlighted
Moderator

Re: Airwave 8.2.10.0

For the LDAP case; does the LDAP server use older ciphers?  If so, toggle the 'Support Deprecated Ciphers' option under AMP Setup -> Authentication -> LDAP Config

 

For the CLI account access failing after upgrade -> nothing from the CLI changed.  You can always go through the AMP recovery route to reset the ampadmin password - this is detailed in the AMPCLI appendix of the User Guide.


Rob Gin
Senior QA Engineer - Network Services
Aruba Networks, a Hewlett Packard Enterprise Company
Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: