Wired Intelligent Edge (Campus Switching and Routing)

Reply
Highlighted
New Contributor

2930F + AP303 + Controller 7005 / Multi SSID VLAN Setup

Hello,

 

I´m currently setting up a new network for a customer, which would like to have 4 SSIDs, each with a different VLAN and normal WPA2 login.

(I know, there are other ways, but the customer want´s it exactly like that).

 

This is the current setup:

Switch 2 - 2930F (IP Address 192.168.63.22):

Default Gateway: 192.168.55.1 (VLAN 55),

Router with IP 192.168.55.1 on Port 24 (Default VLAN 1)

Switch 3 on port 50

AP 1 on Port 13 (VLAN 63 untagged, Port IP Address 192.168.63.22)

Default VLAN 1 IP Address: 192.168.55.47

 

Switch 3 - 2930F (IP Address 192.168.63.23):

Default Gateway: 192.168.52.22

Switch 2 on Port 50

AP 2 on Port 39 (VLAN 63 untagged, Port IP Address 192.168.63.23)

Controller on Port 40 (VLAN 63 untagged)

 

Controller 7005:

IP: 192.168.63.201

Port 0/0/0 admin state enabled (link to switch 3) all other disabled

Management VLAN 63

 

Router config as it was told to me from out ISP:

Master:
address 192.168.55.2/24
virtual-address 192.168.55.1/24
    vif 48 {
        address 192.168.48.2/24
            virtual-address 192.168.48.1/24
    vif 49 {
        address 192.168.49.2/24
            virtual-address 192.168.49.1/24
 

Long story short:

A workmate started this project, now its my. I started with about 90% of the actuall configuration (changed a port and some little things) and i never worked with aruba components before.

All 4 WLANs with different VLANs must get access to the internet.

I have searched on google (where i found this community) and set the trunk port on the controller.

On the switches, the vlans are tagged, and at this point i don´t know where the mistake is.

I have added some pictures from the config sites (yes I am a gui fan ;) ), had to blur some parts, because of the company name.

 

2930_2.png2930_3.png7005_1.png7005_2.png7005_3.png7005_4.png7005_5.png


Accepted Solutions
Highlighted
New Contributor

Re: 2930F + AP303 + Controller 7005 / Multi SSID VLAN Setup

Hello,

and sry for this late answer.

Our ISP "forgot" to set up the VLANs on the router, so everything ended by the switch -.-

We set it now up with intervlan routing and every vlan has an own ip.

Now it is working.

View solution in original post


All Replies
Highlighted
MVP Guru Elite

Re: 2930F + AP303 + Controller 7005 / Multi SSID VLAN Setup

Do you have a schema ?

 

do you want to use routing feature of 2930F ?



PowerArubaSW: Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP... More info

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...) More info

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)

PowerArubaIAP: Powershell Module to use Aruba Instant AP

PowerArubaMC: Powershell Module to use Mobility Controller / Master


ACMP 6.4 / ACMX #107 / ACCP 6.5 / ACSP
Highlighted
New Contributor

Re: 2930F + AP303 + Controller 7005 / Multi SSID VLAN Setup

Hello,

and sry for this late answer.

Our ISP "forgot" to set up the VLANs on the router, so everything ended by the switch -.-

We set it now up with intervlan routing and every vlan has an own ip.

Now it is working.

View solution in original post

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: