Wired Intelligent Edge (Campus Switching and Routing)

Upcoming community maintenance Oct. 27th through Oct. 29th
For more info click here
Reply
Highlighted
Occasional Contributor I

Re: How to configure GUI access on aruba 2930F swicth?

XXXX-SW1# sh flash
Image Size (bytes) Date Version
----------------- ------------ -------- --------------
Primary Image : 29335147 11/19/18 WC.16.07.0003
Secondary Image : 29335147 11/19/18 WC.16.07.0003

Boot ROM Version
----------------
Primary Boot ROM Version : WC.16.01.0005
Secondary Boot ROM Version : WC.16.01.0005

Default Boot Image : Primary
Default Boot ROM : Primary

Highlighted
MVP Guru Elite

Re: How to configure GUI access on aruba 2930F swicth?

What the web-management configuration ?



PowerArubaSW: Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP... More info

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...) More info

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)

PowerArubaIAP: Powershell Module to use Aruba Instant AP

PowerArubaMC: Powershell Module to use Mobility Controller / Master


ACMP 6.4 / ACMX #107 / ACCP 6.5 / ACSP
Highlighted
Occasional Contributor I

Re: How to configure GUI access on aruba 2930F swicth?

Hi 

No SSL only http

password operator user-name "operator" plaintext "password"
password manager user-name "admin" plaintext "password"

 

IP address is configured in VLAN 

Getting the following error

error.png

Highlighted
MVP Guru Elite

Re: How to configure GUI access on aruba 2930F swicth?

do you have try to make erase config ? (and upgrade to last firmware ?)



PowerArubaSW: Powershell Module to use Aruba Switch API for Vlan, VlanPorts, LACP, LLDP... More info

PowerArubaCP: Powershell Module to use ClearPass API (create NAD, Guest...) More info

PowerArubaCX: Powershell Module to use ArubaCX API (get interface/vlan/ports info)

PowerArubaIAP: Powershell Module to use Aruba Instant AP

PowerArubaMC: Powershell Module to use Mobility Controller / Master


ACMP 6.4 / ACMX #107 / ACCP 6.5 / ACSP
Highlighted
Occasional Contributor I

Re: How to configure GUI access on aruba 2930F swicth?

Hi

Thank you for your quick response .Will check and let you know

Highlighted
New Contributor

Re: How to configure GUI access on aruba 2930F swicth?

How can I access the switch ip address if its in another subnet than what I am on? I have a network that is only used as mgmt of devices. Firewall rules on my end permit m,e to access but the Aruba switch will only let me access management if I am in the same network. For example, I am on 10.10./16 network, Mgmt network is 172.16.30.x/24. I can fully access anything on 172 networks based on my rules on the third-party firewall, but the Aruba switch will not allow me to manage the switch from 172.16 networks unless I am on that network. Any suggestions? I've setup Ip authorizations, they seem to not be of any help. What in the Aruba is preventing this?

Highlighted
Occasional Contributor II

Re: How to configure GUI access on aruba 2930F swicth?

You need a routing to access IPs outside of your subnet.

 

try "ip default-gateway X.X.X.X" on the switch.

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: