Wired Intelligent Edge (Campus Switching and Routing)

How to configure, verify and troubleshoot IGMP and PIM-SM functionality

Aruba Employee
Aruba Employee

What is IGMP?

The Mobility Access Switch supports Internet Group Management Protocol (IGMP) as defined in IETF RFC 1112 (IGMPv1) and RFC 2236 (IGMPv2). IGMP allows hosts and adjacent routers on IP networks to establish multicast group memberships.


What is PIM?

Protocol-Independent Multicast (PIM) is a family of multicast routing protocols for Internet Protocol (IP) networks that provide one-to-many and many-to-many distribution of data over a LAN, WAN or the Internet. It is termed protocol-independent because PIM does not include its own topology discovery mechanism, but instead uses routing information supplied by other traditional routing protocols such as the Border Gateway Protocol (BGP). There are four variants of PIM, of which theMobility Access Switch supports PIM Sparse Mode (PIM-SM).

What is PIM-SM?

PIM Sparse mode (PIM-SM) explicitly builds unidirectional shared trees rooted at a rendezvous point (RP) per group, and optionally creates shortest-path trees per source. PIM-SM generally scales fairly well for wide-area usage. PIM-SM is useful for routing multicast streams between VLANs, subnets, or local area networks (LANs) in applications such as IPTV.


IGMP Config:

To configure an IGMP profile, follow these steps:

    1.     Configure an IGMP profile under an interface profile.
             (host) (config) #interface-profile igmp-profile igmp1
             (host) (Interface IGMP profile "igmp1") #
     2.     Enable IGMP profile (default is enabled).
             (host) (Interface IGMP profile "igmp1") #no disable
     3.     Assign IGMP profile to a VLAN interface.
             (host) (Interface IGMP profile "igmp1") #interface vlan 2
             (host) (vlan "2") #igmp-profile igmp1
      4.     Verify the VLAN interface.
              (host) (vlan "2") #show interface-config vlan 2

vlan "2"

Parameter Value
--------- -----

Interface OSPF profile ospf-a0

Interface PIM profile default

Interface IGMP profile igmp1

Interface shutdown Disabled

mtu 1500

IP Address

IPv6 Address N/A

IPv6 link local Address N/A

DHCP client Disabled

DHCP relay profile N/A

Interface description N/A

To configure PIM-SIM end to end, follow these steps:
    1.     Create a VLAN.
            (host)(config) #vlan 7
            (host)(VLAN "7") #exit
    2.     Create an interface-profile switching-profile profile to associate with a physical interface.
            (host)(config) #interface-profile switching-profile ip-sp-profile
    3.     Add an access-vlan to set the VLAN when interface is in access mode.
            (host)(switching profile "ip-sp-profile") #access-vlan 7
            (host)(switching profile "ip-sp-profile") #exit
    4.     Associate the interface-profile switching-profile with a physical interface profile.
            (host)(config) #interface gigabitethernet 0/0/0
            (host)(gigabitethernet "0/0/0") #switching-profile ip-sp-profile
            (host)(gigabitethernet "0/0/0") #exit
    5.     Create the routed VLAN interface (RVI).
            (host)(config) #interface vlan 7
            (host)(vlan "7") #
    6.     Assign an IP address to the routed VLAN interface (RVI).
            (host)(vlan "7") #ip address netmask
    7.     Associate the "default" PIM profile with the routed VLAN interface (RVI).
            (host)(vlan "7") #pim-profile default
            (host)(vlan "7") #exit
    8.     Use the router pim command to enter Global PIM profile mode and define the RP address and group range.
            (host)(config) #router pim
            (host)(Global PIM profile) #rp-address group-range


To Verify PIM Sparse Mode follow the method suggested below,

Displaying PIM RPF Information


(host) #show ip pim rpf


PIM RPF Information




Address Nexthop RPF Interface


------- ------- ------------- vlan20


 Displaying PIM Neighbor Information


To display PIM neighbor information, use the following command:


(host)# show ip pim neighbor


PIM Neighbor Information




Interface Neighbor IP UpTime Expiry


--------- ----------- ------ ------


vlan11 07:58:51 08:00:20


 Displaying PIM RP Information


To display PIM RP information, use the following command:


(host)# show ip pim rp


PIM RP-Group Mapping




Group/Prefix RP


------------ --


 Displaying PIM Mroute Information


To display PIM Mroute information, use the following command:


(host)# show ip pim mroute


IP Multicast Route Table


Flags: D - Dense, S - Sparse, C - Connected, L - Local,


P - Pruned, R - RP-bit set, T - SPT bit set, F - Register Flag


J - Join SPT, A - Assert Winner


(*, 14:20:11 RP flags:


Incoming Interface: vlan11 RPF nbr:


Outgoing Interface List:


vlan22, 14:20:11


(, 14:17:20 RP flags: T


Incoming Interface: vlan22 RPF nbr:


Outgoing Interface List:


vlan11, 14:17:20

Displaying PIM Statistical Information


To display PIM statistical information, use the following command:


(host)# show ip pim stats


PIM Statistics




Interface Counter Value


--------- ------- -----


vlan11 Rx Hellos 0056


Rx Join/Prune 0000


Rx Join 0000


Rx Prune 0000


Rx Register-Stop 0000


Tx Hellos 0057


Tx Join/Prune 0016


Tx Join 0000


Tx Prunes 0000


Tx Register 0000


Invalid Hellos 0000


Invalid Join/Prune 0000


Invalid Join 0000


Invalid Prune 0000


Invalid Register 0000


Invalid Register-Stop 0000



Version history
Revision #:
1 of 1
Last update:
‎11-04-2014 01:09 PM
Updated by:
Labels (1)

 HI all,


We are going to implemet a CCTV network in a building. No other system will include in this. Network structure will be, one core switch and all other are edge switches. Totally 800 cameras and we are going to split into four r five networks with VLAN. Need to enable the IGMP multicast. Kindly share the configuration details for the same in core switch and edge switch as well. Below find the details. I have already performed the Multicast in Avaya but here I am new for Aruba products. Pl support.


Core switch - Aruba 5412R  zl2 - 1 No's

Edge switch - Aruba 2530-48G - 28 No's

Total VLAN - 6 (1 NW mgmt & 5 - CCTV mgmt)

CCTV control server and storage server will be connected in one dedicated edge switch.

Requirement - Need IGMP multicast configuration and other, if any required for this CCTV network for Core switch and edge switch.


Thanks in advance. 





Search Airheads
Showing results for 
Search instead for 
Did you mean: