Wireless Access

Hi All,

 

I'm running an ArubaOS 8 testsetup consisting of

1 Mobility Master 8.0.1.0

1 VMC 8.0.1.0

1 AP-105

 

I've got connectivity but I'm unable to make the ap use channel-bonding. I've done all the config at the /md node. I've attacted the config. AP is provisioned in ap-group Diekgait:

 

(DL-ArubaMM-02) [md] #show ap database

AP Database
-----------
Name Group AP Type IP Address Status Flags Switch IP Standby IP
---- ----- ------- ---------- ------ ----- --------- ----------
AP01 Diekgait 105 192.168.1.8 Up 4h:15m:25s 2 192.168.1.201 0.0.0.0

 

But it does not select a bonded channel:

 

(DL-ArubaVMC-01) #show ap bss-table

fm (forward mode): T-Tunnel, S-Split, D-Decrypt Tunnel, B-Bridge (s-standard, p-persistent, b-backup, a-always), n-anyspot

cluster (cluster role): U-UAC, A-AAC, sU-Standby UAC, sA-Standby AAC

Aruba AP BSS Table
------------------
bss ess port ip phy type ch/EIRP/max-EIRP cur-cl ap name in-t(s) tot-t mtu acl-state acl fm cluster datazone
--- --- ---- -- --- ---- ---------------- ------ ------- ------- ----- --- --------- --- -- ------- --------
24:de:c6:af:33:a0 Diekgait.nl N/A 192.168.1.8 g-HT ap 1/19/19 0 AP01 0 4h:16m:39s 1500 - 68 T no
24:de:c6:af:33:a8 Diekgait.nl N/A 192.168.1.8 a-HT ap 116/24/24 4 AP01 0 4h:16m:39s 1500 - 68 T no

 

Any idea?

The AP-105 doesn’t 80MHz channels , it is an 802.11n AP

You need an 802.11ac AP 2xx or 3xx

The AP-105 doesn’t support 80MHz channels , it is an 802.11n AP

You need an 802.11ac AP 2xx or 3xx

I'm not asking for 80 mhz, but for 40 mhz. Right now it will only do 20 mhz.

Here you go:
http://www.arubanetworks.com/pdf/technology/whitepapers/requirementsfor80211ac.pdf

Here you go:
http://www.arubanetworks.com/pdf/technology/whitepapers/requirementsfor80211ac.pdf

Sorry misread your original request

Can you validate that the 802.11a radio profile has wide-channels enabled

Also under the SSID > HT SSID profile the 40 MHz and HT is enabled

Get Outlook for iOS

See here:

 

rf dot11a-radio-profile dot11a-dl
csa
dot11h
arm-profile arm-dot11a-dl
max-channel-bandwidth 40MHz
eirp-max 127
!
wlan ht-ssid-profile ht-ssid-dl-test
!
wlan ssid-profile ssid-dl-test
essid Diekgait.nl
opmode wpa2-psk-aes
dtim-period 5
a-basic-rates 12 24
a-tx-rates 12 18 24 36 48 54
g-basic-rates 18 24
g-tx-rates 12 18 24 36 48 54
max-retries 4
max-clients 128
wmm
wmm-vo-dscp 46
wmm-vi-dscp 26
wmm-be-dscp 0
wmm-bk-dscp 8
local-probe-req-thresh 10
wpa-passphrase *****
max-tx-fail 25
ht-ssid-profile ht-ssid-dl-test
g-beacon-rate 18
a-beacon-rate 12
qbss-load-enable
!

 

 

If you want so see more I have attaced the config in the first post.

Sorry misread your original request

Can you validate that the 802.11a radio profile has wide-channels enabled

Also under the SSID > HT SSID profile the 40 MHz and HT is enabled

Get Outlook for iOS