Wireless Access

Reply
Frequent Contributor II

AP 555 in restricted mode.

Hi community I'm testing a new AP 555, I have a virtual controller and a 3810 switch to connect the AP, the problem is that the AP boots and it is provisioned well but the System LED status is in Amber - Solid which means that the AP is in "restricted power mode (limited PoE power available, or IPM restrictions applied), no network restriction" (based on the installation guide).

I have tried to power the AP with a PoE-AT injector but it remains on the same status.

 

There you have the ouput of system-status command:

Power Status
------------
Item                        Value
----                        -----
Power Supply                : POE-AT
LLDP Power                  : 0.0W
Current Operational State   : 1 ETH port disabled; USB power disabled; 5GHz radio: 4x4
Eth0 HW POE status          : POE AT, LLDP power: 0.0W
Eth1 HW POE status          : NONE, LLDP power: 0.0W
POE Mode                    : Shared

Also the output of show ap active:

(VMC-LAB) [mynode] #show ap active

Active AP Table
---------------
Name    Group  IP Address   AP Type  Flags  Uptime  Outer IP  Cluster Role  Radio 0 Band Ch/EIRP/MaxEIRP/Clients  Radio 1 Band Ch/EIRP/MaxEIRP/Clients
----    -----  ----------   -------  -----  ------  --------  ------------  ------------------------------------  ------------------------------------
AP-555  FONT   10.30.0.171  555      pA2a   19m:9s  N/A                     AP:5GHz-HE:36E/18.0/29.0/0            AP:2.4GHz-HE:1/9.0/29.4/0

Flags: 1 = 802.1x authenticated AP; 2 = Using IKE version 2;
       A = Enet1 in active/standby mode;  B = Battery Boost On; C = Cellular;
       D = Disconn. Extra Calls On; E = Wired AP enabled; F = AP failed 802.1x authentication;
       H = Hotspot Enabled; K = 802.11K Enabled; L = Client Balancing Enabled; M = Mesh;
       N = 802.11b protection disabled; P = PPPOE; R = Remote AP;
       S = AP connected as standby; X = Maintenance Mode;
       a = Reduce ARP packets in the air; d = Drop Mcast/Bcast On; u = Custom-Cert RAP;
       i = Provisioned as Indoor; o = Provisioned as Outdoor;
       p = Restriction mode in POE-AF/AT;r = 802.11r Enabled; f = No Spectrum FFT support;
       Q = DFS CAC timer running; T = Flex Radio Mode is 2.4GHz+5GHz;
       U = Flex Radio Mode is 5GHz; V = Flex Radio Mode is 2.4GHz; e = custom EST cert; W = Dual 5GHz Mode Enabled; 4 = Using WiFi Uplink

Channel followed by "*" indicates channel selected due to unsupported configured channel.
"Spectrum" followed by "^" indicates Local Spectrum Override in effect.

Channel flags: +/- = 40 MHz, E = 80 MHz, S = 160 MHz, E+E = 80 + 80 MHz (i.e. 36E+149E)

Cluster Role: U = UAC, A = AAC, SU = Standby UAC , SA = Standby AAC


Num APs:1
 

 Thank you in advance!


Daniel Méndez Vargas
ACMP, ACCP
Highlighted
Occasional Contributor II

Re: AP 555 in restricted mode.

The 555 needs 802.3bt to run without restrictions

 

edit:  When powered by DC, 802.3bt (class 5) POE or 2x 802.3at
(class 4) POE, the AP will operate without restrictions

 

from: https://www.arubanetworks.com/assets/ds/DS_AP550Series.pdf

Aruba Employee

Re: AP 555 in restricted mode.

Couple things:

1. Did you update the DRT table?
https://www.arubanetworks.com/techdocs/DRT/Content/ReleaseNotes/Upgrade/DownloadableRegulatoryTable.htm

2. Enable LLDP on the switch ports

3. Plug two cables into it. Disable the second port on the switch, but leave the PoE on.

That will give it enough power to run without restrictions.
Thanks,

Zach Jennings
Aruba

Re: AP 555 in restricted mode.

As an alternative you could enable IPM, which will operate the AP without restrictions (initially) even when using a single 802.3at POE source. However, IPM may quickly apply restrictions as the AP starts handling traffic, to ensure the AP does not exceed the POE budget.

You could configure the AP to minimize power consumption, or wait for IPM to kick in and apply restrictions (as configured).

/Onno
Frequent Contributor II

Re: AP 555 in restricted mode.

Thanks to you all!

 

It's clear now. I forgot to check the data sheet (my bad)


Daniel Méndez Vargas
ACMP, ACCP
Frequent Contributor I

Re: AP 555 in restricted mode.

Hyjack of this thread but I think this should go together with this; how do I get the 2nd 5ghz radio enabled and/or visible?

 

Running code 8.5.0.2: MM with 7200 series cluster

AP-555 is not in restricted mode; no "p" flag. On 802.3at PoE+

IPM is enabled (order power off usb, eth1, g radio)

both LED are green.

lates DRT file activated

LLDP enabled and power handed out by LLDP

connected 2 ports in aggregation (disabling 1 port didn't work on 2930F with code16.06.006)

 

both show ap active and sho ap bssid only shows 1 a and 1 g radio. Disabling the g radio doesn't make a difference. SSID scanner shows single 5Ghz channel with SSID 

 

Same AP Group has 345 enabled in Dual 5Ghz mod

 

thanks

Erik

ACDX#968, ACMP, ACCP, ACSP
Aruba

Re: AP 555 in restricted mode.

The mode where the AP-555 splits up the 8x8 radio into two independent 4x4 5GHz radios will be supported in 8.6 code only.

In 8.5, it's a fixed 8x8 radio.

/Onno
Frequent Contributor I

Re: AP 555 in restricted mode.

Thanks Onno, I wasn't aware of that. Is there an ETA on 8.6 that may be communicated?

 

rgds, Erik

ACDX#968, ACMP, ACCP, ACSP
Aruba

Re: AP 555 in restricted mode.

Not the right forum for roadmap info, but Q4CY19 is vague enough ;-)

/Onno
Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: