Hi,
we do initial config on controller 7010,after the first configuration finished the controller get reload,and then when the controller is up,the controller back to controller setup :
here the log from the controller CLI :
Current choices are:
System name: Test
Switch Role: standalone
VLAN 1 interface IP address: 172.16.0.254
VLAN 1 interface subnet mask: 255.255.255.0
Option to configure VLAN 1 interface IPV6 address: no
Country code: us
Time Zone: pst-8:0
Ports shutdown: no
If you accept the changes the switch will restart!
Type <ctrl-P> to go back and change answer for any question
Do you wish to accept the changes (yes|no)yes
Creating configuration... Done.
System will now restart!
Shutdown processing started
Syncing data....done.
Time sync [Done]
Please stand by while rebooting the system.
Stage 1 Loader 1.0.5.0 (build 56553)
Built: 2016-09-22 at 05:02:10
Secure Boot Enabled on the Processor
Bank: Primary
CPLD: rev: 3.0 (30:0060|32:0002|33:0000|34:0000|35:0000)
PRID: 000C1203
POWER ON RESET CFG:30CC0FF2
Initialized I2C0 Controller.
Initialized I2C1 Controller.
SPD Rev:0x11 DIMM:0 Type:2 Speed:666MHz #Rank:1
DDR3: Node 0 Channel 0 Mem size = 4096 MB UDIMM
set freq:666666
DDR3: Node 0 DRAM frequency 666 MHz
DDR3: Node 0 CPU frequency 800 MHz
mtb_ps:125 clock:1500 trc:33 trcd:9 trp:9
AP3:A0CFFF0 ODTP1:10000
Board DDR VDD set to 1.5V.
N:0 CH:0 additional rdlvl rdly:1
N:0 Ch:0 m:32 s:32 R OK.
Rank:0 HW WLVL Passed Mask:1FF
AP3:A0CFFF0 ODTP1:10000
n:0 ch:0 RTT WR:0200
===N:0 Ch:0 m:32 s:32 RW OK.
Node:0 Ch:0 TGE Set Memory:4096 MB value:FF FF -- PASS
Node:0 Ch:0 TGE Set Memory:4096 MB value:FF 00 -- PASS
Node:0 Ch:0 TGE Set Memory:4096 MB value:AA 55 -- PASS
Node:0 Ch:0 TGE Set Memory:4096 MB value:00 00 -- PASS
DDR3 Initialization Passed.
NBU0 DRAM BAR0 base: 00000000 limit: 0013f000 xlate: 00000001 node: 00000000 ( 0 MB -> 320 MB, size: 320 MB)
NBU0 DRAM BAR1 base: 001d0000 limit: 00bff000 xlate: 00090001 node: 00000000 ( 464 MB -> 3072 MB, size: 2608 MB)
NBU0 DRAM BAR2 base: 00e00000 limit: 0128f000 xlate: 00290001 node: 00000000 ( 3584 MB -> 4752 MB, size: 1168 MB)
Hit Ctrl + X keys to stop autoboot: 0
CPBoot image is signed
Verifying CPBoot checksum...
CPBoot check passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
## Starting application at 0x8C100000 ...
CPBoot 1.0.7.0 (build 56553)
Built: 2016-09-22 at 04:52:12
DRAM: 4 GB
Detected [XLP208 Rev B1 (Secure Boot) ] (6a|6a)
CPLD: rev: 3.0 (30:0060|32:0002|33:0000|34:0000|35:0000)
Flash: 16 MB
PCIE (B0:D01:F0) : Link up (Gen(1))
Bank: Primary
Board: A7010
CPU: XLP208 Rev B1 (Secure Boot)
Clock: Core 800 MHz / SoC 800 MHz (30cc0ff2)
Net: ge-0, ge-2, ge-3, ge-4, ge-1
Inventory Verification: PASS
Hit Ctrl + X key to stop autoboot: 0
USB0: setting speed to USB_SPEED_HIGH
2 USB Device(s) found
#1 Storage Device(s) found
##Loading image 0:0######################################
Image is signed; verifying checksum...
passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
0:xlp_napi_vc_mask 0xf
0:sae frequency is 500
0:nlm_hal_set_sae_engine_sel: xlp2xx return
0:-- SAE Frequency set to 500
0:cde frequency is 333
0:CDE Frequency set to 333MHz
0:MSGRING_NAPI: Initializing NLM NAPI subsystem
Aruba Networks
ArubaOS Version 6.4.3.4 (build 51619 / label #51619)
Built by p4build@formentera.arubanetworks.com on 2015-09-10 at 20:14:07 PDT (gcc version 4.4.5)
Copyright (c) 2002-2015, Aruba Networks, Inc.
<<<<< Welcome to Aruba Networks - Aruba A7010 >>>>>
Probing for EEPROM devices [ OK ]
Probing for real-time clock [ OK ]
Initializing LCD module [ OK ]
Uncompressing core image files [ OK ]
Extracting corefs [ OK ]
Enabling watchdog [ OK ]
Starting device manager [ OK ]
Performing eUSB Flash fast test... [ DONE ]
[ OK ]
Mounting flash [ OK ]
PoE firmware [ OK ]
Checking system inventory [ OK ]
Installing ancillary FS [ OK ]
Performing integrity check on ancillary partition 0 [ OK ]
Reboot Cause: User reboot (Intent:cause:register 78:86:50:60)
Starting syslog service [ OK ]
Restoring the database [ OK ]
Generating SSH keys [ OK ]
Initializing TPM and certificates [ OK ]
Checking for configuration upgrade [ OK: Intra-Version Upgrade ]
Starting OS services [ OK ]
Starting auto provisioning
Using port gigabitethernet 0/0/15 for auto provisioning
Initiated DHCP, awaiting DHCP response
Auto-provisioning is in progress. Choose one of the following options to override or debug...
'enable-debug' : Enable auto-provisioning debug logs
'disable-debug' : Disable auto-provisioning debug logs
'mini-setup' : Stop auto-provisioning and start mini setup dialog for branch role
'full-setup' : Stop auto-provisioning and start full setup dialog for any role
Enter Option (partial string is acceptable): full-setup
please help us to resolve this issue..
Thank You All.